DIY Bath and Shower mixer valve repair - Moen 1222 posi-temp cartridge replacement

DIY Bath and Shower mixer valve repair - Moen 1222 posi-temp cartridge replacement - it's easy!

Рет қаралды 212,657

robdude1969

4 жыл бұрын

Moen 1222 One-Handle PosiTemp Faucet Cartridge Replacement - cartucho de ducha - cartouche de douche
Restore usability to One-Handle faucets that are leaking or not operating properly with the Moen One-Handle PosiTemp Faucet Cartridge Replacement. This replacement cartridge is designed specifically for use with Moen One-Handle PosiTemp tub and shower faucets. It features brass and plastic construction and is designed for easy installation.
Fix your Moen shower valve mixer cartridge. When the shower handle stops letting the water come out, it's time to open it up. It's super simple. There are many handle variations, but if it's Moen, the innards should work the same. Pop off the handle cap, unscrew a couple screws, pull out the clip and use vice grips or cartridge extractor to get the cartridge out. Lube up the new one and put it back in. You can do this! Fix your shower valve, you probably don't have to replace the whole fixture.
The Moen 1222 as the same as the Moen 1222b. The "b" stands for bulk.
The Moen 1222HD is the commercial strength Heavy Duty version. These cartridges are the standard replacement for Moen bath and shower fixtures.
The Moen 1200, 1225, and 1248 cartridges are similar and will come out in a similar manner.
Please hit the thumbs up button to like, Subscribe for more videos, and share it where you think it would help someone out. Thanks again and good luck on your shower valve repair!
Moen 1222 Posi-Temp cartridge replacement
DIY shower valve repair
Bath and shower mixer valve maintenance
Moen 1222 cartridge removal
Shower valve troubleshooting
Moen Posi-Temp repair guide
DIY faucet cartridge replacement
How to replace Moen 1222 cartridge
Shower valve cartridge installation
Step-by-step Moen 1222 repair
Moen Posi-Temp valve disassembly
Bath and shower mixer valve repair tips
Tools needed for cartridge replacement
Common shower valve problems
Moen cartridge repair video tutorial
Moen 1222 Posi-Temp valve maintenance
Shower faucet troubleshooting
DIY plumbing repair for shower
Moen cartridge replacement cost
Easy shower valve repair at home
These keywords should help you find relevant information and guides for the DIY repair of a Moen 1222 Posi-Temp cartridge in a bath and shower mixer valve. Always follow proper safety precautions and refer to the manufacturer's instructions for the best results.
Buy the stuff you need for this shower repair here from these affiliate links:
Moen 1222 One-Handle Posi-Temp Faucet Cartridge Replacement for Moen Tub Shower and Shower Only Configurations, Brass and Plastic - amzn.to/2xq89Z1
Moen 1222HD Commercial Heavy-Duty Brass Shell PosiTemp One-Handle Tub Shower or Shower-Only Faucet Cartridge Replacement - amzn.to/2TPZiY9
Moen 104421 Cartridge Puller for 1200, 1222 and 1225 Single Handle Cartridges - amzn.to/2xmDxrf
Danco 86712 Moen Cartridge Puller, Pack of 1, Silver - amzn.to/428SJCA
Locking Pliers Set - amzn.to/2VViAhr
Screwdriver, 6-in-1 Multi-Tool - amzn.to/2vJnlA9
For something more interesting, try listening to audio books. I love having a good book read to me while I work or drive. They sure beat top 40 radio these days!! Here's a link to a free month of Audible. Enjoy!!! Prime members get an even better deal! - amzn.to/36mNLFJ
You ever have groceries delivered? Try Amazon Fresh and let the groceries come to you. - amzn.to/3bNfzUI

Пікірлер: 109

@mikem9852 Жыл бұрын

My Moen tub/shower valve was originally installed in 2008 when I remodeled the gust bathroom. Recently, I used the shower to make sure everything worked okay since we had company coming. When on the hot water setting, the pressure dropped off to a trickle. Watched a few videos and found out that the cartridge (1222) needed to be replaced. Picked up a new cartridge at Home Depot for $54. The old cartridge would not come out like shown in this video, even using the plastic notched piece that came with the cartridge. Tried pulling it out using vice grips. Watched a few more videos and found out I needed a cartridge remover tool. I went to Lowes (closer) to pick up a Moen Cartridge Remover Tool. Found the Moen 1222 cartridge a lot cheaper for $38. Damn. The cartridge finally came out with the remover tool. Sanded out the inside of the valve with #320 sandpaper, cleaned it out and installed the new cartridge with no problem.

@petersawicki4403 Жыл бұрын

Thanks for the help I am going through the same problem right now!

@RobertTozzi 8 ай бұрын

@@petersawicki4403 Same here!

@omarrohoman3726 2 жыл бұрын

Based on your video I was able to replace my leaking valve ,Thank you

@cmarkjenkins Жыл бұрын

The water bottle tip was great-our shower is in the basement and still drained out a lot of water-the bottle saved a big mess behind the wall-thanks!

@jong2k4 3 жыл бұрын

One of the best plumbing videos of all time- relaxed and to the point with accurate info!

@robdude1969 3 жыл бұрын

Just doing my part to pass it forward! thanks!

@haroldrull4943 3 жыл бұрын

Right on.... nice and very calm but perfect video.

@robdude1969 3 жыл бұрын

Thanks. Good luck with your repair!

@hardyholladay8288 2 жыл бұрын

Thank you, your video is exactly what I needed.

@robdude1969 2 жыл бұрын

So glad it helped!

@foilcap 3 жыл бұрын

Don't even think about starting this job without a puller. If the cartridge is stuck due to deposits - you'll have a hell of a time trying to pull it out.

@joseluiscaceres1458 3 жыл бұрын

I bought the puller in case I need it. Thx

@BSRFD 2 жыл бұрын

Oh my god are you ever right. First time ever replacing one of these and I cannot get that damn cartridge out no matter how much force I use. I know I am going to be sore tomorrow. Just ordered that cartridge puller tool online and will have to suffer a dripping faucet for a few more days until it arrives from Amazon lol.

@sergiomiranda5648 2 жыл бұрын

I went through living hell pulling the cartridge without the puller. Huge mistake. Learned my lesson.

@christlopherbrandimarte4520 11 ай бұрын

WD-40 works wonders...should replace every couple of years to avoid cartridge getting wedged inside shower body due to water deposits .

@frankgonz31 11 ай бұрын

I actually didn't use it, cartridge came with a plastic cap that helps twist and then just pull off with a plier, now inserting back is taking me awhile as I text 😅

@doctorhino8736 2 жыл бұрын

Thanks, this helped me realize I could fix it myself before calling a plumber. I did have to buy the Moen extraction tool for the cart. It was 20 years old and practically soldered in there

@robdude1969 2 жыл бұрын

Congrats!!!

@valenciabbk 2 жыл бұрын

Thank you so much

@harrietwilson7144 2 жыл бұрын

Very good 👍

@marjanhafezi5027 Жыл бұрын

Very helpful🙏

@mellymelle76 2 жыл бұрын

Thank you! 😊

@g.fortin3228 2 жыл бұрын

Looks good... and ..Thank you.

@emanuelsolis5120 2 жыл бұрын

Thank you

@bashj7379 3 жыл бұрын

Hey It was very helpful video Thanks again.

@joelcintron 11 ай бұрын

Thank you for the video it helped tremendously looking forward to seeing more

@robdude1969 11 ай бұрын

Cheers to a lovely refreshing shower.

@bashj7379 3 жыл бұрын

Thanks for this super tutorial

@robdude1969 3 жыл бұрын

I hope it helps!

@billjones5165 3 жыл бұрын

@@robdude1969 how

@SteveLaceyProfessional Жыл бұрын

Feels like Bob Ross, Plumber.

@robdude1969 Жыл бұрын

I feel happy on my shower. The soap makes happy little clouds.

@arunkumarkbv994 3 жыл бұрын

very helpful, thanks much.

@melystubbie9960 Жыл бұрын

Nice thank u

@theoldyellr 2 жыл бұрын

I notice you first had the cartridge with the notched flat on top, then the correct way with the notched flat on the bottom, the correct way. This is important.

@johnmack4470 Жыл бұрын

Unless the water lines for hot and cold were installed opposite- I had a plumber do that!

@dannygren1790 7 ай бұрын

This video showed me there was no inner handle adapter required on Moen Posi-Temp trim kits that use a handle attached to the center with a phillips head screw. Newer Posi-Temp handles use a allen head (hex head) screw at a 90 degree angle to hold the handle on and therefore require an adapter. Thank you!

@mitchelfisher9422 2 ай бұрын

I have a shower that won't mix properly. The valve is clear and functional. There is a thump as you turn from hot to cold and back, and then it just gets hot or cold

@robdude1969 2 ай бұрын

Yikes! That doesn’t sound right.

@johnmack4470 Жыл бұрын

Two big points not in this video. First on older cartridges they won’t come out unlesd you loosen them first, use a puller, and pray a lot! Second, the clips don’t go in the bottom holes of the cartridges easily. Sometimes you have to push the new cartridges in about 1/32 of an inch more and slightly bend the bottom of the clip towards the slot. Old copper clips almost never work with new cartridges so buy a new clip just in case.

@robdude1969 Жыл бұрын

Thanks for the added suggestions.

@jhuynh0912 3 жыл бұрын

At any point do you need to turn the water back on to check for any leaks? i put the new cartridge and pin in. Should i turn the water on after that step to check for leaks or do all the steps and wait to turn back on at the end?

@TM_Stone 10 ай бұрын

Easy if it goes accordingly. I'm in the process of doing this now. Second replacement on the same shower. The first time was easy. However, this time a whole other story. The handle stem was welded onto the cartridge stem by corrosion. It took a cutoff wheel to remove the whole handle. Massive pain to remove. This is the reason why Moen changed the design. No more metal on metal contact.

@robdude1969 8 ай бұрын

bummer. I hope you got it! I had a similar problem with a bike seat post - aluminum fusing to steel. Total mess.

@billrhea 4 жыл бұрын

You need to put lots of that oil Inside too. There are lots of o rings inside too

@frankycheechoo1126 Жыл бұрын

Would you be able to check if works with out having to assemble it all together again ?

@notbanksy8294 3 жыл бұрын

Do you know if NOT having a temp limit stop would make it not operate correctly? Seems like it wouldn't hold the valve body in place?

@JONSEREDdotWS Жыл бұрын

Ok I did that but now I have blend on right off at top and cold on left. Do I need to switch the tab with H C to the bottom?

@jeanciaccio5170 3 жыл бұрын

my cartridge stem has alip on it that prevents the pull tool from sitting all the way in against the cartridge. what do i do ??

@MrBojem3a Жыл бұрын

This little kzfaq.infoUgkxVoi3B4CB6Oygq1-vo4OTL1M_M5JkrXif tub works perfect in our 6 x 6 shower and is easy to get in and out. Also easy to drain.

@robdude1969 Жыл бұрын

Awesome! hope it helps!

@melgomez7268 4 жыл бұрын

My problem was the opposite!! Your video helped me a lot but now is leaking a little bit maybe my replacement is defective!!!

@robdude1969 4 жыл бұрын

Check those seals. Are they well lubricated? Any tears or abnormalities in the surface? Any dirt or other particles stuck to the cartridge or in the opening? Good luck!!

@melystubbie9960 Жыл бұрын

I hace a diff handle but I will try it

@robdude1969 Жыл бұрын

How did it go?

@sh2697 2 ай бұрын

i didnt use that much lubricant. now im wondering if i should take it back out

@franknguyen9655 2 жыл бұрын

Hi, I replaced the cartridge.,I get hot and warm water. I do not get just cold water. I have tried another cartridge with the same problem. Do you know how to fix this issue? Thanks

@rohitbhatnagar7599 Жыл бұрын

I am getting low water temp from shower, so I will put new 1222B. To measure the temp of water coming in, do you know how can measure without the 1222B. What is the name of the plumbing assembly that the 1222b goes into, so I can ask home depot also

@lindasampson7363 Жыл бұрын

Good thing that lube didn't come in a 55gal. drum!

@joelr9955 11 ай бұрын

Hi, do anyone know if cartrigdges have style printed on it? Because my looks like Moen but doesnt have brand name i wll apreciate any help thx

@nmflyerrobbin5413 2 жыл бұрын

you turned off main water Do you need to turn off water heater also?

@aorforever2334 3 жыл бұрын

Here is a simple trick to get the valve out. Take off the shower head and replace with a standard end cap (1/2" black iron cap - less than $2). Take the pin off the cartridge and turn on the main water supply. Wait until the valve is pushed out by water pressure or you can help it out with pliers. (Have someone ready to turn off water supply) Done!

@robdude1969 3 жыл бұрын

That doesn’t sound suspect at all. Lol.

@aorforever2334 3 жыл бұрын

@@robdude1969 You didn't think of it, so you ridicule and minimize its effectiveness - shame on you.

@robdude1969 3 жыл бұрын

I don’t doubt it’s effectiveness. It’s just funny to think of the valve shooting across the tub before your buddy gets the water off. Thanks for watching! 🥂🥳

@aorforever2334 3 жыл бұрын

@@robdude1969 I doubt your method I have no evidence like you, but I still doubt it. Imagine all you want, but you are just guessing and it's bad guessing. You could hold the cartridge from moving with your hand, it's not going to shoot out like a bullet - if so the clip that holds it in place under normal operation would break and shoot out like shrapnel. Shop trying to be in charge - it's embarrassing!

@christlopherbrandimarte4520 11 ай бұрын

For those who don't know this trick, the water pressure pushes the cartridge out. Very simple 2 person job. One person at the water main shutoff, one person at the shower body.

@mikepitt8924 2 жыл бұрын

My moen leaked behind the shower wall, it’s not the pipes that are leaking because the leak stopped when I shut it off, will changing the center part what you just showed stop the leak? Or do I need a plumber to come out? Can you let me know. Thank you in advance!

@robdude1969 2 жыл бұрын

Once you pull the cover off, you can have a better look. Sorry I can’t really help more.

@ppark61 3 жыл бұрын

Great video! I get only extremely hot water. Do you think it is failure of the cartridge?

@g.fortin3228 2 жыл бұрын

maybe need to turn down your water heater a bit.

@Danny-fx1zq 3 жыл бұрын

I'm having an issue getting the pin back in to hold the new cartridge. It's not going in a smooth as yours LOL. Please help

@robdude1969 3 жыл бұрын

On my way. Lol. Wish I could help.

@OuttaHere7 2 жыл бұрын

Easier than the Roman style tub!!! The 1248 cartridge. No index and ver fine threads to deal with.

@jayjy1583 11 ай бұрын

Dang brother you supposed to turn that faucet on and clear that water out of them pipes before you pull that LOL

@Lachos17 2 жыл бұрын

Mine is leaking in to the inside wall . this could be the problem ? I already se that leaks when I open the valve

@robdude1969 2 жыл бұрын

Yes. It can rot the walls, floor, cause mold and much damage if not sealed properly. Good luck!

@paulgettinger5983 Жыл бұрын

I tie a price of string with a slip knot before removing the clip so I Do not loose it.

@robdude1969 Жыл бұрын

Good tip!

@Nick-xs3bg 5 ай бұрын

So if the old one has the c/h markings facing the bottom i would imagine i install the new one the way the old one came out?

@robdude1969 5 ай бұрын

how did that work out for you?

@Nick-xs3bg 5 ай бұрын

Well I've got plenty hot water now

@PaakJo 4 жыл бұрын

My house was built in 2003, first time thinking of changing the cartridge bcos is leaking. What model of moen replacement cartridge do I buy. thank you

@kumarbhatia6566 3 жыл бұрын

You should contact Moen but most likely it is like mine (about 20 years old house with original Moen cartridge) p/n 1222B. You MUST consider the cartridge pull-out tool before starting this job. The Moen original is about $33 (CAD) but Canadian Tire offers a compatible tool @ $12 (CAD). The cartridge is the posi-temp series but best to ask Moen for a confirmation.

@kobesyn24 11 ай бұрын

I can't get the retainer clip on!

@mikes6301 2 ай бұрын

I was told that if you put the”H/C” on the bottom, you can do that if you want the hot water to come out first. Could that be true?

@robdude1969 2 ай бұрын

Tell us how that goes. 🫣

@brendamiller4200 2 жыл бұрын

My faucet was leaking I removed the cartridges 1222 replaced with a new moen 1222 still leaking what do I need to do

@robdude1969 2 жыл бұрын

Was it leaking from the mixer? Was there corrosion or any build up of mineral deposits that may prevent a good seal?

@amigo203 10 ай бұрын

What kind of lubricant are you using?

@robdude1969 8 ай бұрын

It was included with the valve but it felt like silicone.

@pacmancalgary 4 жыл бұрын

Thanks for the demo. What kind of Rolex are you wearing?

@chancecayenne3200 3 жыл бұрын

THE KIND IF U HAVE TO ASK U CANT AFFORD IT! BROKE ASS!!

@Outplayedqt 3 жыл бұрын

@@chancecayenne3200 wtf bro

@amomandotherstuff 3 жыл бұрын

Moen replaces parts for free- DO NOT BUY ONE OF THESE CARTRIDGES! Call Moen. Also, when I replaced mine, it was to try and stop a squealing/howling shower. Well, that’s fixed but, according to Moen, the tub faucet leaks now because I used the oil my new cartridge came with to oil it...as the instructions instructed (and every KZfaq video). Moen says they come pre-lubricated. They’re sending me a new one AND emailed me their instructions. Good luck!

@robdude1969 3 жыл бұрын

Thanks for sharing. That’s great to know. I would love a lifetime warranty on everything I fix!!

@billducas 2 жыл бұрын

I bought 2 of these and one came with the packet of oil, and the other came with a packet of silicone grease. From previous experience, I'd used the silicone grease. Didn't feel right about using the oil, and you just confirmed it. Thank you.