(DIY) Fix/repair faulty Mouse click | How to replace mouse button or clicker or switches
Рет қаралды 13,987
5 жыл бұрынThis video will fix those unwanted double clicks, and no clicks at all, caused by defective mouse button or clickers of your gaming/non-gaming mouse.
This procedure will work to any kinds of gaming or non-gaming mouse. It will just vary on how to disassemble it.
FOr the mouse clicker, I bought it at Shopee PH for 28Php each. You can use either Omron or Huano brand. It's better if you will buy the one that is rated at 10 to 20 million clicks. I've used Huano rated at 20 million clicks to my CM Storm Havoc for this video.
Please subscribe for more videos.
Follow me at facebook: za.gl/FTOs5jy
"Music: Positivity Is The Energy by Redafs.com, Licensed under Creative Commons: By Attribution 3.0 License"
@jhonerrolborlagdan2489 4 жыл бұрын
Thanks, better than buying a new one
@nhatphongjsc5107 4 жыл бұрын
AWESOME!
@orlypalomar 3 жыл бұрын
I recently replaced the microswitches on two of my mice and they're now like brand new. The only thing I'd do differently in the video is to give the mouse a thorough cleaning. It looked filthy, inside and out. Not passing any judgment because my mice also do get dirty after some rigorous use. But since you're already servicing the mouse, it shouldn't take any more time to whip out a paint brush to clean the inside and some mild cleaner on a cloth to clean the outside.
@marcelanno8580 4 жыл бұрын
did same on my Steelseries Kinzu v1 :D
@cajamanual6713 4 жыл бұрын
5 años con este mouse y no me ha dado ningún problema.
@royregis1129 4 жыл бұрын
Do I need to buy a helping hand/third hand tool to hold the pcb board? And can I just do this with no gloves on any floor/surface? Thanks
@user-ve1cc6qn6t 3 жыл бұрын
You don't need helping hands but it is way easier with them, try soldering on a table or on the floor and make sure if the solder doesn't drop onto anything else.
@earthpotato5143 2 жыл бұрын
You can try to cover the surface below with paper or something and tape down the pcb board to prevent it from moving.
@mckevindauntless698 3 жыл бұрын
Boss matanong ko lang po? Ano po gamit niyo na soldering iron? At ano po tawag yung tape na 3M? Maraming salamat po
@TheSmileysCrew 3 жыл бұрын
How do I find out my mouse’s nominal actuation count rating. I dont know what switch to buy
@p1nky02 3 жыл бұрын
All switches fit every mouse
@TheSmileysCrew 3 жыл бұрын
@@p1nky02 ok 👌
@lynx873 3 жыл бұрын
I want to change mouse into really soft click bcoz I have muscular dystrophy
💀Skeleton Ninja🥷【にんげんっていいなチャンネル】
Рет қаралды 8 МЛН
Jervin Kabigting
Рет қаралды 18 М.
Beardedbob
Рет қаралды 159 М.
TorqueCars
Рет қаралды 8 М.
Photographer Army
Рет қаралды 9 МЛН
ГЛАЗУРЬ СТЕКЛО для iPhone и аксессуары OTU
Рет қаралды 6 МЛН
MaxxPC
Рет қаралды 1,3 МЛН