OS FS-120 Disassembly

Рет қаралды 12,913

6 жыл бұрын

I disassemble one of the 2 OS FS-120 engines given to me. This engine's crankcase is damaged and the pump is missing. It will become just spare parts.
To contact me via email please watch:
• How to Contact Me
Please check out my Blog pages
www.rcgroups.com/forums/member...
www.dmrcflyr2.com/#!blog/k40vr

Пікірлер: 16

@PetrincicBrosRC 6 жыл бұрын

Hey Davide my brother. Just came by to say hello from the other side of the world. Nice babies you have there. A lot of spare parts. Stay well and greetings from Slovenia, Robert

@dmrcflyr2 6 жыл бұрын

I appreciate that you stopped by Capt. Robert. Stay well!

@workonesabs Жыл бұрын

I have loads of 120's and generally 20 os 120 pumpers, a supercharged one and the normal OS120e. One of the E models had a broken lug, given to me, the lug was reworked and welded one one and put into a plane, loads of flights later its still going in a Flair Stampe.

@andrublaueair6752 5 жыл бұрын

Hi ,HI ,HI !!!!!! David , U do best staff ,,, I like it ..10+++++ , and thanks for this video about OS 120 ,,, I have 2two and not working , now time to fix ....YYYYYY!!!!!!!

@johngreen5837 4 жыл бұрын

Do you know where can I find a c-12 carb for my fs 120 surpass

@dmrcflyr2 4 жыл бұрын

Search eBay, but no I have no idea. If Tower Hobbies doesn't have them, then the used market is the place to look.

@druefetters6571 4 жыл бұрын

Seeking some input from the master! Having c-12 carb issues reaching out for a hand if that's ok?

@dmrcflyr2 4 жыл бұрын

kzfaq.info/get/bejne/ibNkoNWgyJfXnIk.html

@metalwizard23 4 жыл бұрын

Danny do you have a video of rebuilding one of these pumps and carbs??

@dmrcflyr2 4 жыл бұрын

Who's Danny? No the pumps are not user serviceable from what I understand.

@metalwizard23 4 жыл бұрын

@@dmrcflyr2 well I think I got lucky. My 120 surpass pumper runs pretty decent!

@stevejones9044 5 жыл бұрын

Really enjoying your videos. Extremely informative. But I have a question. You often mention heating the engine to loosen parts. What is the proper way to do it? I'm fine if you want to point me to a video you've done. Do you use a propane burner that's used for sweating copper pipes together? Propane or map gas? I'm just concerned about over heating and damaging something.

@dmrcflyr2 5 жыл бұрын

Heat gun.

@stevejones9044 5 жыл бұрын

@@dmrcflyr2 Seriously! Ok was thinking much hotter. I have a heat gun for monokote but that may not be hot enough. Map or propane might be too hot so I'll go get a heat gun. Even a cheap Wagner heat gun has a range of 750 to 1100 degF.

@dmrcflyr2 5 жыл бұрын

I would never recommend using a flame to heat an engine as the heat is too localized. A heat gun diffuses the heat a bit better and works just as well.

@tedsmith6137 3 жыл бұрын

I put mine in the oven at about 150 C. for about 30 minutes.