Dodge Journey Rocker arm assembly replacement

Рет қаралды 1,786

6 ай бұрын

In this video I show you how to replace the rocker arm assembly on a 2010 dodge journey. the job is a little long but not hard to do. its usually the rear exhaust rocker for cylinder 3. this will give you a misfire and the infamous dodge tick (ticking) noise. If you enjoyed the video please leave a like, comment, share and subscribe. Thanks!
Tools and parts:
Tools used in most videos:
socket set: amzn.to/2ycTz7U
plier set: amzn.to/2Zs7na3
ratchet wrenches: amzn.to/3bXLYrz
electric ratchet: amzn.to/2ZDjOzQ
flash light: amzn.to/3egL5vS
pliers set: amzn.to/2AZqrC5
screwdriver set: amzn.to/2TESsFv
gloves: amzn.to/2TESsFv
pick set: amzn.to/2ZAfwsL
Disclaimer:
Due to factors beyond the control of JunkyardJunkie, I cannot guarantee against improper use or unauthorized modifications of this information. JunkyardJunkie assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. JunkyardJunkie recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of JunkyardJunkie, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not JunkyardJunkie.
0:01 - intro

Пікірлер: 20

@DependableAutoTruck 2 ай бұрын

great video have one coming in shop next week to do have done the 3.6 but not the 3.5 thanks for sharing you didn't say torque on intake bolts

@JunkyardJunkie 2 ай бұрын

Thanks! Glad I could help. The intake manifold should be 105 in-lbs. hope this helps. Thanks for watching!

@neilbenz-hz3gc 2 ай бұрын

Hello just finished watching your video. Great video by the way. I was wondering what you did before you put the assemblies on as far as the lash adjusters go. I have new ones that are spongy. And the old ones are solid. I’m changing the rockers because of the wear on the arms, thanks

@JunkyardJunkie 2 ай бұрын

These have auto lash adjusters so you won’t need to set lash or anything. Hope this helps. Thanks for watching!

@izzynutz2000 Ай бұрын

Are these rocker arms interchangeable with the 4.0 same procedure?

@JunkyardJunkie Ай бұрын

Yes they are. Hope this helps. Thanks for watching!

@sergiosanchez4967 4 ай бұрын

Great video!!!! I have a 2009 dodge charger 3.5L that has a very bad ticking noise at start up one it's running for a couple of minutes noise kinda goes away. So I was thinking it might be my rocker arms. Any suggestions? Where did you purchase your rocker arm assembly? Thanks for the video one again.

@JunkyardJunkie 4 ай бұрын

Probably going to be the exact same thing. The chargers had this problem too. First thing I would do is pull your valve cover and look at them and look to see if they have any problems. Then take it from there. Hope this helps. Thanks for watching!

@sergiosanchez4967 4 ай бұрын

Yes sir thank you for your feedback.

@sergiosanchez4967 4 ай бұрын

Did you have to soak them in oil or lubricant, or did you just put them straight on as they came?

@sergiosanchez4967 4 ай бұрын

Also how can I turn my camshaft to where my intake lobe is sticking up how you mentioned in the video. I'm no mechanic I just like to worry on my vehicles to learn more about them and save some bucks lol.

@dynamic_4064 3 ай бұрын

Where did you get your new rocker arm assembly’s from. I got the same issue with my journey but I am on a budget.

@JunkyardJunkie 3 ай бұрын

If your on a budget your probably better off getting them off eBay. Usually when it’s more major parts like this I try to make sure to get OEM parts. Hope this helps. Thanks for watching!

@dynamic_4064 3 ай бұрын

@@JunkyardJunkie 1 More question, were the rocker arms side specific or are they interchangeable?