How To Change Rocker Arms And Lifters On A Pentaster 3.6 2014 Dodge Journey AWD

How To Change Rocker Arms And Lifters On A Pentaster 3.6 2014 Dodge Journey AWD - Part 2 Of 2

Рет қаралды 4,566

Жыл бұрын

#dodge #journey #tick
In this video I attempt my biggest job yet. I set out on a journey with the Dodge Journey. If you have an annoying ticking sound that is coming from your engine, and you have the right amount of oil, then it is more than likely a rocker arm. In this video, I show you the long and tedious process of how to change out the rocker arms and lifters on a 2014 3.6 L engine, all-wheel-drive SXT Dodge Journey.
Here is a list of parts I used:
1. Rocket Arms (12 per Cylinder Head - 24 Total)
www.partsgeek.com/mmparts/roc...
2. Lifters (12 Per Cylinder Head - 24 Total)
www.oemmopar.parts/oem-parts/...
3. Special Timing Chain Tensioner Tools:
DPTOOL 6PCS Camshaft Phaser Timing Chain Tools for VW Jeep Chrysler Dodge 3.6L Pentastar 10200A+10202 10369 Cam Locking Tool
a.co/d/99HwBrN
4. RTV Automotive Sealent:
Permatex 82180 Ultra Black Maximum Oil Resistance RTV Silicone Gasket Maker, Sensor Safe And Non-Corrosive, For High Flex And Oil Resistant Applications 3 oz
a.co/d/aTRmll3
5. Valve Cover Gasket Set:
Valve Cover Gasket Set - Compatible with 3.6L V6 Dodge Journey, Durango, Avenger, Jeep Cherokee, Wrangler, Ram 1500, ProMaster, Chrysler 200, 300 - Replace VS50805R, 5184596AE
a.co/d/0X0RKoj
Special Tools That I Used:
1. 1 inch 36mm Socket
ARES 71156-36mm Low Profile Fuel Filter Socket - Low Profile Design for Easy Access - Chrome Vanadium Steel with Manganese Phosphate Coating to Resist Rust and Corrosion a.co/d/0HOADRc
2. Breaker Bar
Neiko 00339A 3/8-Inch-Drive Premium Breaker Bar, 12 Inches Long, Nut Breaker Bar, 180-Degree Flex Cr-Mo Head with Cr-V Steel Construction a.co/d/iweQnDn
3. Torque Wrench 🔧
LEXIVON Inch Pound Torque Wrench 1/4-Inch Dr. | 72-Tooth Gear Dual-Direction Click Type | Micro-Adjustment 10~150 in-lb (1.1~16.9 Nm) | Zippered Protective Case (LX-180) a.co/d/brV4Mld
4. Plastic Scraper
Limited-time deal: Double Edged Plastic Razor Blade Scrapers Knife with Contoured Grip for Scraping Labels and Decals Sticker From Glass, Windshields and Auto Window Tint Vinyl Tool Application(Scraper with 10 Blades) a.co/d/3Z40sGV
5. Replacement Mopar Wire And Hose Fasteners
95 PCS Car Moulding Wire Harness Loom Routing Clips Fender Flare Panel Blind Rivets Rocker Clips Assortment Black Nylon for Jeep Wrangler JK 2007-2015 68039280-AA Ford GMC Chevrolet
a.co/d/1VaOlgS
I hope this video helps you save money and do this job yourself. Remember to take breaks when when you get frustrated and to believe in yourself. 👍🫶

Пікірлер: 54

@Vaniusp 6 ай бұрын

The best video on the subject.

@Mr_Goody 6 ай бұрын

Thank You for the kind words. 👍

@MikeLJ-ku7ov 2 ай бұрын

The shallow socket I couldn’t find anywhere thank you for the link very helpful subscribe

@Mr_Goody 2 ай бұрын

You’re welcome. 👍

@crazybillsgarage Жыл бұрын

Very nice, great job.👍

@oiygfdxssfgg 5 ай бұрын

Good video, thanks for posting this

@Mr_Goody 5 ай бұрын

Your Welcome 👍

@looneyboy2828 Ай бұрын

Question as I’m doing this to mine this weekend. Would I be ok just using the cam phaser lock on the left side as my issue is on the right side or would I need to use all the locking tools on the left side as well thanks

@Mr_Goody Ай бұрын

I’m not for sure if I understand your question correctly, but you just use it on the side that you’re working on at the time.

@kenten1472 6 ай бұрын

It's difficult hearing a "camshaft" called a "crankshaft" multiple times. I get it and appreciate the video regardless.

@Mr_Goody 6 ай бұрын

I noticed that after I made the video. 🤷🏻‍♂️

@papabits5721 9 ай бұрын

You could also cleaned off the reluctor rings on the cams too.

@Mr_Goody 9 ай бұрын

You’re right, I did do that, just not on camera.

@thephnxtrading Жыл бұрын

Hello, so i replaced the rockers and lifters on rear bank and replaced right intake cam. While the valve cover was still off, I rotated the crank 360° to make sure everything rolled good, i proceeded until the horizontal line on phasers lined up and when i did I noticed the timing chain markings i made were no longer lined up. Is that supposed to happened?

@Mr_Goody Жыл бұрын

Are you talking about the right cylinder? Head closest to the back of the engine? The paint marks should line up. Remember on the front of the engine on the front head the arrows will point toward each other, and on the back they will point away from each other. I hope that makes sense to you, but to answer your question the paint marks should line up.

@thephnxtrading Жыл бұрын

@@Mr_Goody Yes the 1 closest to rear engine

@brianvinzant1893 Жыл бұрын

Would this be the same for a 2010 3.5L journey? I cant find a video on my car specifically

@Mr_Goody Жыл бұрын

This is only for the 3.2 and 3.6 Pentastar engine.

@thephnxtrading Жыл бұрын

When I go to the junkyard to find camshafts do they need to be from a 3.6L Journey or can I use one's from Jeep & Town Country 3.6L engines?

@Mr_Goody Жыл бұрын

Any vehicle that has the Pentastar 3.6 L should work just fine to replace your camshaft.

@thephnxtrading Жыл бұрын

@@Mr_Goody Does it have to be a 3.6L VVT or is a 3.6L okay for use?

@Mr_Goody Жыл бұрын

@@thephnxtrading VVT

@Chris-ir5ft Жыл бұрын

I have a question about the rocker arm and Hydraulic tappet I changed both and sometimes he still makes the same noises befor i changed it at the same position When it is cold, it makes no noise and runs very quietly and well and when it is warm, the noise sometimes comes for 10 seconds and then disappears again I did both sides of the engine can you help me? 😅😁

@Chris-ir5ft Жыл бұрын

I left the hydraulic tappets in the oil for 3-4 hours so that the air goes out and he can fill himself with oil

@Mr_Goody Жыл бұрын

At the top of the page on my channel banner, click on my Instagram and you can chat with me that way or in the about section you can email me and I will try my best to help you

@tomferguson9287 Ай бұрын

My rocker arm bolt broke. Where do I find a replacement?

@Mr_Goody Ай бұрын

At your local Chrysler dealer or Amazon or eBay. They sale wholesale Mopar parts.

@timothysexton7621 8 ай бұрын

Did you have issues with the cam locking block tool?

@Mr_Goody 8 ай бұрын

There is a lot of 3-D print made of these and honestly it just depends from different sellers. I’ve had no problem with them fitting right on and then with others. I had a little bit of problem and had to wiggle them on a little bit. I hope that answers your question. And I think for this particular vehicle I might have had to cut the back one, so it would clear the frame. Just check in the video.

@louieunomusix3864 2 күн бұрын

how much can i expect to pay for this mechanical job?

@Mr_Goody Күн бұрын

I would say in parts you’re looking at about $400 and the rest would just be your own labor if you do it yourself. But if you take it to Garage, it’s gonna be a lot more and it just varies and white Garage I’ve seen it cost from 1.5 K to well over $2000..

@MikeLJ-ku7ov Ай бұрын

Any idea why the timing chain tool is so difficult to engage the tensioner on the left side or nearest the fire wall ?

@Mr_Goody Ай бұрын

Well, it been sidemounted in some of the vehicles like the Dodge Journey makes it more difficult to get to. I myself had to modify the tool that fits in between the phaser sensors and cut it in half so that it could fit in and wedge in where it supposed to. Also you wanna make sure that you have released attention with the tool that they supply you with the timing chain. Sometimes you will need to move the links and lined them up to the wedge to just barely into accomplish this you can slightly move the crankshaft if you need to, but in the end, make sure that the arrows are lined up like they’re supposed to doing those two things should give you a little wiggle room to fit the wedge in better. Also it is sometimes hard to find an exact low profile socket to fit on the side mounted engines too, but I believe I left a link to where you can buy them and they’re not too expensive. so hopefully a few of those ideas will help you my friend. It is not impossible to do. It’s just a pain in the butt. Sometimes they manufacture the cars and sometimes you have to modify the tools or do simple little tricks to get the tools to fit for that particular car.

@Mr_Goody Ай бұрын

The tensioner can get stuck sometimes and you just have to keep working with it.

@MikeLJ-ku7ov Ай бұрын

@@Mr_Goody the bolt is in the tool grove I’m not exactly sure where the tool should be making contact the bracket on the tensioner to release it. Was told I didn’t need the hook wire tool on the fire wall side so I’m just poking around like I had never done this before thanks for any suggestions and thank you for posting

@MikeLJ-ku7ov Ай бұрын

Does the tool simply hold the chain but not loosen it ? If so I might be good thanks for the help I can’t make a stupid mistake

@Mr_Goody Ай бұрын

@MikeLJ-ku7ov it should loosen it also. It provides some slack in the chain when it releases it, and then it allows the wedge to fit in between the camp phasers easier, and then if you need to adjust the campers, you can slightly move the crankshaft to line up with the wedge.

@thephnxtrading Жыл бұрын

How to remove the Phaser sensor that has 3x hex screws, its so close to the AC line

@Mr_Goody Жыл бұрын

If you could look up at the top of my page, there is a banner that has my Instagram account. If you could message me on Instagram and send me a picture of what you’re talking about. I will try to help you the best I can. 👍

@thephnxtrading Жыл бұрын

Sorry I don't have Instagram just Twitter. Hello, I figured it out and got valve cover off back bank. My next question is the front bank(Leftside) is fine no damaged camshaft or rocker arms, just the back bank(Rightside)Has damaged cam/rockers, to get those cams off do I have to do anything to the front bank besides having arrows lined up and rotating camshaft 30° to get lobes of arms?

@Mr_Goody Жыл бұрын

@@thephnxtrading As long as you take the bearing caps off that should be all you have to do. But make sure you rotate the camshaft before you take the bearing caps off and not after.

@adamnpigeon7185 Жыл бұрын

Only 24 new rocker arms are needed right? I saw the count in the info said a total of 48. TYA! :)

@Mr_Goody Жыл бұрын

Yes on this engine 24 total rocker arms and 24 lifters.

@adamnpigeon7185 Жыл бұрын

@@Mr_Goody Thank you! Awesome instructional video.

@Mr_Goody Жыл бұрын

You are welcome my friend. 👍

@papabits5721 9 ай бұрын

You should have used some assembly lube or at least some oil on the caps.

@Mr_Goody 9 ай бұрын

I did this too.

@don-cw1yz 8 ай бұрын

The question to me is why Stelantis can't make this engine more reliable? They put this engine in a lot of their vehicles so why can't they engineer the engine better. Consumers do want to buy unreliable vehicles.

@Mr_Goody 8 ай бұрын

I agree with you 100%. I believe during the last three years that they made these vehicles they were pretty reliable. They changed and revised the parts as they went along and had a pretty good dependable car near the end but what they should’ve done is the go back and fix the cars that they knew was going to have problems instead of Letting the people pay for repairs and being guinea pigs. It’s very unfortunate.

@don-cw1yz 8 ай бұрын

@@Mr_Goody What years did the 3.6 Pentastar get revisions that made it a more reliable engine?

@chitownchapito701 Ай бұрын

Mine is making a. Lifte noise not as bad but ya :(😢