I am happy you are enjoying the videos!

Thank you! Do you have the B2 or A1 version?

@@BrokeLifeEU I have the PKHAP 20-Li A1 version. It says Kompernass on the label, Mfg 2019-08. I doesn't have the antivibration in the handle that yours does. I have used it with a 4AH Battery.

The anti-vibration handle I think does not do a lot unfortunately. @@typhoontim125

I have a video coming up with this C3 and a 20V brushed version in which the test is mostly in stone. I think that will be interesting for you. In this video the concrete on the left was rather weak, however the piece on the right was tough to do. If I did not pull out the drill bit to decompress they would get suck quite easily even with the 5mm in most cases.

If the movements are very slight it is fine, but if there is a huge amount of movement I would just ask for another one. I hope I have managed to help you just a little.

Thank you! Unfortunately I have never tried the B2. I have only tried the C3 from Kompernaß and Grizzly.

@@BrokeLifeEU better version grizzly or kompernass?

@valeriocoelho8138 In general I would say Kompernaß are always the better Parkside tools.

@@BrokeLifeEU concerning the new impact wrench B4(grizzly), it's quite better quality than the A2(kompernass), more powerful at speed 1 and the esthetic is miles ahead. So it depends

@jkd2038 It is good to hear that! I can only hope they will deliver better and better tools at great prices!

Hvala vam! Nažalost, nemam B2 s kojim bih ga usporedio. Ali ne mislim da će biti toliko drugačiji.

Da točno. Ali ako ga trebate u kući, lijepo ga je imati.

@@BrokeLifeEU za tu cijenu svakako. Čak je vrlo praktičan za upotrebu kad si na ljestvama ili u nekom nezgodnom polozaju. Po mojoj procjeni,s obziirom da sam radio sa Makitom,nema vise od 2 J udarac,što je vrlo dobro za ciglu. Ne napravi vecu.

4ah is enough, the 8ah will mostly just result in a longer run time for home needs. I have another video in which I use it with the 4Ah against a 12V with the 4ah. That will give you an idea of what it‘s like with the 4ah.

Yes, indeed I am seeing reports of that. My hands are itching to try it and see what happens 😂. It is also interesting to see if it will be a battery issue or a tool issue in the end.

@@BrokeLifeEU If you can find a replacement tool in a local lidl store, than try it. But this is what will happen. the update bar will show that all is going well, keeping steady pace and when it is around 100%, there will be a message that connection has been lost. than you will see the bluetooth blue led bliniking on the tool. and as per instructions, you will have to reconnect the battery to the app and try again. the battery will need 5 to -6 attempts to connect with the app and when it does, you will see that the app will read, that there ia no tool connectd to the smart battery. after doing the procedure 2 or 3 more times, you will see that the app does not recognise the tool. it will aknowledge that there is a tool connected but no model will be recognised. you will try again , and one more time, to the end , it will report that connection has been lost. by that time the tool led bluetooth will keep blinking eradically. do it if you can find a replacement and you don't want to wait a replacement from the service center.

​@@BrokeLifeEUhow to update the tool ? Through parkside app ?

I also have some Ferrex tool videos if you are interested 😅

@@BrokeLifeEU No thank you. I was only stupid enough to waste money on parkshit.

@zefautino Einhell? I am looking in to that.

@@BrokeLifeEU So far, so good with Einhell. Can't complain. The day I can, I'll make sure everyone knows.