This video shows how to remove a dry sleeve cylinder liner with simple tools. The engine in the video is a Perkins Diesel 4.236.
Пікірлер: 31
@cubleycat5 жыл бұрын
Oh wow, the more I watch the better it gets, people always freak out when I tell them I hammer liners out so its great to see some else do it. Many years ago when I was in my 20s I figured if I put the old piston in upsidedown the rings would catch hold of the liners lip and I used a piece of hard wood and a sledge hammer and thrashed the liners out, worked a treat. to put the new ones in I used another block of hardwood and the big hammer, it worked perfectly! # think outside the box!
@cubleycat5 жыл бұрын
OMG pure genius, I love a mind like yours which thinks "what can I use that does more than one job". I live by the code myself after all why spend a fortune on a single dedicated tool when you have a whole set of other uses in that kit. Thank you so much for posting this video :-)
@CajunWolffe5 жыл бұрын
Damn, bolt a strong back across the bottom of the crankcase, put a small bottle jack or hydraulic ram between it and your "puck," and get after it. The wood is absorbing all of your force, and that's why you have to hit it with a hammer, you shouldn't have to. I do dry sleeves all the time and could have had all four out before you could get that device rigged up. By the way, a machine shop can make that puck out of a piece of scrap metal for at or less than the cost of that wheel bearing removal set from harbor freight, but then again, I have that set as well as the whole ball joint toolset, and they are handy for all kinds of things around a shop. Great for those upper control arm bushings attached to 4x4 Jeep front axels.
@AlphaBobFloridaOverlord2 жыл бұрын
Could you pack the cylinder with dry ice (with a rag stuffed on top for insulation) and do all the pulling from the top? Regardless, Great Video and very appreciative that you took the time to make this series!
@georgenetherway60715 жыл бұрын
Know my way around these engines.Really,if your doing it for a customer you should get them non finished and get them bored out to original spec.Otherwise the new liner tends to follow the bore if slightly tapered or oval.But great job .
@timericksom11058 жыл бұрын
running a weding bead inside the liner will shrink it enough to slide it out
@AbdulKurad5 жыл бұрын
Good job sir
@Z71Ranger9 жыл бұрын
Great Video... Thank you for posting it...
@Erichhh9 жыл бұрын
Outstanding ingenuity! Thanks for this. Is that a water-cooled air conditioning system visible at 8:40 atop the Janitrol furnace? The shutoff valve on the extra PVC pipe looks like it may be a water feed. Have been thinking about using well water as a low-cost A/C system assist and this reminded me of it.
@ProjectsbyTMD9 жыл бұрын
Erichhh Thanks for the complement! On another project, I completely overhauled the Goodman/Janitrol AC system. I installed thermostatically controlled pressure expansion valves on the indoor and outdoor units to get more energy out of the AC/heat pumps. On the indoor units, I just completely replaced the evaporator & put on PVC valves to turn off the air bleed for water condensation. I only turn them off during the winter - since one need to have the valve open when the AC is on during the summer.
@steze489 жыл бұрын
I have a Massey 255 that needs a sleeve and piston....Sleeve is cracked at the top about 1/2" long downward and piston has been indented from a dirt dobber nest going through no. 4...My bad for not pulling the intake first...DOOH! This will help me...
@ProjectsbyTMD9 жыл бұрын
steze48 - Glad to hear that it can help!
@leschampsmarins13926 жыл бұрын
Hi! my name is Roberto, have a small question! while removing the sleeve by turning the puller,would it have help to fill the old sleeve with ice and salt mixture or dry ice,(salted ice doesn't go has much down has dry ice but get down lower than regular ice) and if not would it be overdone to put dry ice in the sleeve has you remove it?
@engineaissa82117 жыл бұрын
good job
@aircommuter3 жыл бұрын
is there room to get the puck in place with the crank installed for in frame job?
@ProjectsbyTMD3 жыл бұрын
I think so ... but it would be much easier to do on an engine stand
@wimklop16103 жыл бұрын
Hey I just seen your video on pulling dry sleeves. I am wondering how long it roughly took to pull 1 out?
@ProjectsbyTMD3 жыл бұрын
30-60 minutes?
@donnaberger75927 жыл бұрын
Thanks for this. I just pulled liners on a MF 275. Perkins a4.248 50 years old. I welded 8 vertical beads and pulled with a large washer and assorted back ups. Came out really easy. Love your bearing puller. Did you mic any of the bores before / after? What size all thread ? Looks like 1/2". I used that but because i welded. I saw a guy use 3/4" thrd bar and no tapping. Brute force but it worked. I took out all four liners. Thanks!
@ProjectsbyTMD7 жыл бұрын
Donna - didn't mic the bores before/after. The threaded rod was 3/4" with a fine thread.
@jeffbryant66896 ай бұрын
You can weld a bead from top to bottom in a couple of places and have it out in five minutes
@wasimmsheiel92104 жыл бұрын
U can brak this sleeve from side dont need to pull out Just brake it man
@NesarChowdhury6 жыл бұрын
I 'll buy "HTF Type Tensioner (For Main bearing Open) and Cylinder Liner Removal tools advise me manufacturer details.
@robidk27045 жыл бұрын
well now I know I cant rebuild by backhoe with engine in it :(
@yopage7 жыл бұрын
How many horses is this engine?
@timericksom11058 жыл бұрын
welding bead
@randalllyons84676 жыл бұрын
All the comments that say weld a bead on the liner, why does that not make it expand instead of contract?
@fatman123925 жыл бұрын
When the weld shrinks from cooling it pulls the liner with it.
@donkmeister5 жыл бұрын
Not a welder, but I would assume that the liner doesn't expand much when it's welded (as it has a big thermal mass and is heatsinked by the block) but the weld bead goes on very very hot indeed, hence shrinks a little as it cools, thus pulling in the diameter of the liner.
@aliahmadbilal6665 жыл бұрын
Man, that is too much work . All you need is a workshop hydraulic press