DSG 7 Speed Mechatronic Installation (DQ200)

Рет қаралды 109,086

Күн бұрын

Installation of the DQ200 DSG 7 speed mechatronic after our rebuild has been carried out, this will not need Basic Settings as all original adaptations are retained.
Common Failure Symptoms Before Rebuild:
No gear engagement
No drive or reverse
EPC light illuminated
Main 30 amp fuse constantly blowing
www.ecutesting.com/common-fau...

Пікірлер: 56

@TheGeeksofNature 3 жыл бұрын

Excellent job

@mariocars7720 2 жыл бұрын

Good evening mechatronic removal / refitting how many hours? adaptation / calibration ... suitcase there for how much in total?

@raymondbisset Жыл бұрын

Has the top 2 selectors got 3 positions, I can only move the top left selector in 2 positions. I pulled the mechatronics unit off because the car would not move and I got a P 0841 code & a small discharge of oil out of the breather. Im not sure if I have also a G box issue?

@rmsyster 2 жыл бұрын

Can you tell me what a 0 clutch is? Mine is broken and it costs like €9000 euro's according the mechanich. Please advise.

@matroksu Жыл бұрын

So what about passat b8 with that transmission? change that oil and mechatronic oil? or not? and how much milage? thx.

@bvipul1 3 ай бұрын

What is a memory child part in mechatronics?

@amatpenting3060 Жыл бұрын

Thanks for watching bro

@a.h7761 2 жыл бұрын

Hi there How do you pressurise the accumulator please

@jean-remyjrledone1284 2 жыл бұрын

very serious company ,I set again the repeared and reset mechatronic DSG7 without any pb ,pay attention to the little join when set it on the gearbox.

@ritcherklooster324 3 ай бұрын

is it normal when theres fluid in the tcm electric board on the mechatronic unit?

@yatyatim9321 2 жыл бұрын

Thanks you for your explanation ..i'm technician Volkswagen from Malaysia can you explain the true adaption for me

@benaustin7850 2 жыл бұрын

We are doing one and have lined everything up, we get a clunking noise and the engine almost does a back flip

@hifihighend 2 жыл бұрын

Perfect🥂

@ProfitableSalvage 2 жыл бұрын

When refitting and you say change forks to neutral does the car gearstick inside car need to be in neutral or park?

@Ecutestinglimited 2 жыл бұрын

Hi. Yes, the car gearstick and gearbox selector forks should all be in neutral when re-fitting. Cheers

@linasvaiciulis6298 2 жыл бұрын

I have 2010 vw golf mk6 1.6tdi dsg 7 speed gearbox code MLE. Would my car work with the same gearbox removed from golf mk6 1.6tdi dsg 7speed but different gearbox code? Or I need exactly same gearbox code MLE?

@jaystheone1 9 ай бұрын

What was the awsner to this?

@Leon_Brown 2 жыл бұрын

So you dont have to put the breather seal back after filling?

@290Noname 2 жыл бұрын

@shane.bacchus 2 жыл бұрын

Do you have to do any programming of the mechatronic ?

@Ecutestinglimited 2 жыл бұрын

Hi Shane. When we retain the original programming when re-building the unit so no additional programming will be needed when re-fitting it back to the vehicle. All you will need to do is follow the re-fitting procedure, replace the oil and you will be good to go! Cheers.

@reubenmatthew6759 4 ай бұрын

Hi, My Passat 2013 with DSG 7 speed engages when engine gearbox is cold (especially mornings) but doesn't engage when the engine/gearbox is hot. After turning off/On, gear selection happens but Car doesn't move. What could possibly be the issue? Need your support please.

@Ecutestinglimited 4 ай бұрын

Hi. Please email our technical support team at info@ecutesting.com with the following information. Your vehicle's make, model and year of manufacture, the symptoms of the fault including all fault codes, and the part number printed on your mechatronic unit. They will be able to advise you further. Thanks.

@468garage6 3 жыл бұрын

hi there i just followed your turtorial on the replacement .Firstly my original units valve body cracked at the accumalator housing . i then replaced it but used my original board .The car drove but it could only drive in d2 and s2 . Then i saw your video and did the correct bleeding , basically did everything you did.I then now left it in neutral and removed the unit . before installation i measured the selectors to 25mm and made sure the selector forks are neutral while the shifter was in the neutral position . I got everything fitted but i cannot start the car due to me getting a U0101 error code , which means "no communication with tcu/tcm. any help would be great . The car is stuck in park now , park light is flashing and dash says please put vehicle in park.

@Ecutestinglimited 3 жыл бұрын

Hi if you are getting no communications to the DSG mechatronic there may be issues such as poor fitting, bent pins, fuse or feed issue. If the vehicle all checks out as good you are welcome to send us your unit for testing and rebuild if required: www.ecutesting.com/common-faults/volkswagen/volkswagen-golf-audi-a3-dsg-7-gearbox-problem/

@468garage6 3 жыл бұрын

@@Ecutestinglimited the pins we bent yes, thanks for the reply

@alltheusernameswastaken8936 2 жыл бұрын

@@Ecutestinglimited Dam, you guys are awesome for assisting OP

@mrsingh1696 Жыл бұрын

@@468garage6 whichs pins ur talking about where is fuse?

@mrsingh1696 Жыл бұрын

i have same problem but i was on highwar when i changed from D TO S TO OVERTOOK a truck i lost whole gearbox n now pnds flashing with esp light is on errort code u0101

@fernandonhamussua92 2 жыл бұрын

When I put everything back, where should the gear lever be? N or P?

@alltheusernameswastaken8936 2 жыл бұрын

I might be wrong, but the lever is electronic and not mechanically connected and as such its position does not matter.

@290Noname 2 жыл бұрын

In Neutral

@dustyfruitypie1633 Жыл бұрын

I thought VW changed the oil to a mineral oil, on recall, but you are telling people to use an synthetic oil. Am I missing something!

@yatyatim9321 2 жыл бұрын

When mechatronic fluid need to replace n how much kilometers i need recommend customer to replace mechatronic fluid

@Ecutestinglimited 2 жыл бұрын

Hi Yat Yatim, "Volkswagen says no need to change the fluid again. But independents say it needs to be done every 4 years." good-garage-guide.honestjohn.co.uk/askhj/answer/79979/how-often-does-the-oil-in-the-dsg-gearbox-have-to-be-changed-

@JRamirez943 8 ай бұрын

⁠⁠ I’ve got a u0101 error code. 09 Audi a3. Fuses and relays are good no crank no start. Car starts if I jump relay for starter. Power is going to the tcu plug. I unplugged it from tcu and oil came out mech unit. Tried to clean. No luck. P flashing at selector inside car. I have a mech on order but want to be sure before I fit it

@JRamirez943 8 ай бұрын

@ecutestinglimited

@Ecutestinglimited 8 ай бұрын

Hi. We would recommend checking the TCU has a good ground at the connector, as well as good communication lines (CAN high and low) to determine if the fault is with the mechatronic or the wiring.

@wiggumo 2 жыл бұрын

Hi how much to replace this for me

@Ecutestinglimited 2 жыл бұрын

Hi. Select your car make and model on our website here: www.ecutesting.com/common-faults/volkswagen/volkswagen-golf-audi-a3-dsg-7-gearbox-problem/ for accurate prices. Thanks

@wiggumo 2 жыл бұрын

@@Ecutestinglimited thanksdo you provide the installation service as well?

@Ecutestinglimited 2 жыл бұрын

@@wiggumo Unfortunately we do not. However you can follow the steps on this video to re-install your unit if you get it repaired with us. Alternatively you will need to contact a qualified technician. Thanks

@bobansupergenije7512 5 ай бұрын

120 eur

@syedmesfer1879 2 жыл бұрын

Hi I am from INDIA, I want to learn to repair Auto Transmission.

@TheCoBBus 6 ай бұрын

I just paid 5000€ for the unit, fitment, testing, and oils…..

@petar_d488 9 ай бұрын

What makes this f***ing thing rattle so much? I am in a middle of a dispute with Skoda because of this crap, its like marbles in a tin can.

@JRamirez943 8 ай бұрын

Flywheel going bad nothing else. If dsg

@petar_d488 8 ай бұрын

@@JRamirez943 Service says some noise is normal, they are not admitting a problem, my car is under warranty, what do I do, I could use advice.

@juliewanyoike9609 7 ай бұрын

worn out release bearing in the gearbox

@zeljkomilos7244 Жыл бұрын

Hi where Are YOU located do YOU service australia

@Ecutestinglimited Жыл бұрын

Hi. We are located in Derbyshire in the United Kingdom, however we offer a worldwide service so feel free to send your unit in either by filling out our online test form at ecutesting.com, or by giving us a call on +44 1773 535638 Monday-Friday 9am-10pm (GMT). Cheers.