Sooo…. There are intake manifolds out there with dual throttle bodies??

It was likely done for a very good reason. Likely hp & torque at certain RPM range. When the 4.0 was first being developed it supposedly put out 242 hp. One hp per cubic inch. But they were breaking drive train parts. Primarily rear axle assemblies iirc. They were spinning the axle tubes in the housings. Dana had been contracted to build the rear ends and the tooling was shipped to them. When AMC built the rear ends* the axle tube was welded at one point into the rear end housing. Dana thought this is what held the tube in place. Actually the tubes had between .005 to .010" press fit to the housing. When the tubes where pressed in it was so loud that area was enclosed. Manufacturing the rear end housings were a PITA simply because of keeping the three bores in proper alignment. Simply having too high of a clamping pressure would result in the parts being out of spec. *we once made Ring and Pinion sets for Ford. The first sets after they came out of heat treat were set-up on the test machines to run them to check mesh pattern etc. They made excessive noise. The Ford engineer thought they sounded fine. The next test machine had a set of our gears on it. They turned it on and all you heard was a low hum. Every ring and Pinion set in an AMC rear end was a matched set because they where run through a lapping operation as the last step of manufacturing.

If you look through the throttle body, at small throttle inputs the neck makes it so only one side of the throttle body is letting in air. Helps a lot with driveability with the all torque no real hp 4.0

Cylinder distribution played a HUGE part. Curved plenum intakes made more torque, straight plenums made more HP. Plenum volume and it's length made the job difficult for cylinders 1&6. Axles? We tested them by doing forward/reverse shifts at peak torque RPM with the vehicle tied to BIG honking concrete poles. Not sexy. But SO fun to watch them bust shit!

​@@mpetersen6 Every gear set that I have bought be it factory or aftermarket like Richmond gear they all are matched gear sets that are lapped together at these factories that make them . I've never had a problem with a noisy set of gears from Richmond or any stock factory gear sets in the differentials I've built through the years as long as you have the gear tooth pattern set up correctly when checking tooth pattern using yellow pattern grease . I've even set up known good used gears in rear ends that weren't used in the same housing and never had issues other than with used ring & pinion gears you check the coast side of the ring gear pattern more than the driven side because with used ring & pinion gears the driven side is worn more than the coast side of the ring gear and this gives you a more accurate gear pattern . I get what your saying as far as maybe some differential housings can be not exactly the same which is true but that's why different thickness shims are used to adjust for this by either moving the pinion gear in or out more to get that in spec or by shimming the ring gear closer our further away from the pinion gear to achieve the correct tooth pattern. Granted some differentials don't use shims and have adjusters on each end of the gear housing like the Ford 9 inch & Chryslers 8 &3/4 uses where you just turn what sides need to be turned to shift the gear housing in the direction it needs to go to get the correct gear pattern for the ring & pinion . I had GM 12 bolts that were spot welded like you were saying that those welds broke on the 1/2 ton 4x4 trucks and on a Elcamino I worked on & had to pull the rear end out and use a big pipe wrench with the rear end mounted solid so it wouldn't move to a fixture I made to then used the pipe wrench to turn the axle tube back into its correct placement again then re welded those spots again & welded around the axle tube and housing right where that axle tube is pressed into the housing and had no issues with a noisy rear differential. As long as the housing itself is machined correctly for the gear sets and the concentricity is spot on you really shouldn't have any issues with gears not being able to be shimmed or adjusted correctly for the desired gear patterns be it with new or a known good matched set of used gears that were taken out & swapped for a different gear ratio for either a performance gain application or for a fuel milage gain with lower rpm while cruising. I'm sure especially now that there's probably been instances where someone bought a brand new gear set that weren't properly lapped in and they installed them to spec and checked gear tooth pattern and it looked good but the gears whined and made noise because it was a set of gears that got by inspection and quality control but in all the years I've built differentials I've never had a problem like this with a gear set that wasn't lapped in but anything is possible now that most things aren't being made here like they used to be.

Thanks for watching!

How did you tune it

Thanks a lot!

Yea really, then he can make some good power with just the cross flow alone and same volumes of runners

Can you imagine how much business he would get?! That would be so cool.

ford 300? bolt on ? as i think the two are cousins design wise

add jag as well?

How about DOHC crossflow. Yea, we looked at that at JTE....... Beau Coup HP, but torque down low where Jeeps are used? Not much to be gained. Bear in mind, that is where most Jeeps were being used at the time. This was being done on 1990's level engine controls. NOT the 21 Century as is today......where you can dial in SO much.

Camchaft and crazy supercharger

Hey thanks! And yeah, they cover a lot of my videos. I know several of the guys over there and they are good folks. Thanks for watching

@@TheHorsepowerMonster 2005-2006 has a different throttle body because of the IAC valve, I have both earlier and later 4.0 L and they will not fit. F&B also makes 66-68mm throttle body for early 96-04 Jeep 4.0, I have one for over 18 years now.

Thanks!

Thank you! And thanks for watching!

Thanks! And I agree

@@TheHorsepowerMonster Can I get your contact info..

Thanks!

Probably right. Thanks for watching

Agreed.

um the engine's habits for one and 2 what do expect a linebacker to turn into a ballerina cheerleader character ? that's why i feel the 4.0L works better with a manual transmission than a automatic transmission as the potential power band lines up better

Get the banks header, port your straight runner, 4 hole injectors,port the throttle body, relocate the intake air temp sensor to the air box, use lead foot to go fast!!!

Thanks a lot!

They have one it’s on a old episode

Not even that much spring pressure on base my guy

Positive Crank case ventilation system!

@@snoofayy6150 so it's recycled through the manifold? in measured amounts?

Power Nation they show $500 and some horsepower out of an inline 6

Power Nation 500 horsepower inline 6