Echo PB9010T Carb Adjust... WOW the power I have now!!!!!

Рет қаралды 12,626

Жыл бұрын

In this video, I will show and show you how to adjust the carb on your Echo PB9010T blower and the power delivery is insane now!
Music: www.bensound.com/free-music-f...
Gwinnett Lawns performs these services and others such as lawn care, crepe myrtle pruning, light landscaping, spring and fall cleanups, leaf removal in Lawrenceville, Dacula, Grayson and surrounding areas. Take a look at my webpage gwinnettlawns.com/. Check out my new Truth Social GwinnettLawns
#echousa
#echopb9010t
#gwinnettlawns
Here are the items I used in this video.
Walbro Long D Tool▶ 91159L
Walbro Short D Tool▶ 91159s
Ethanol Tester▶ amzn.to/3jQ4lsK
Magnets▶ amzn.to/3R0PlEp
Rubber Coated Magnet Mount GoPro▶ amzn.to/3UvSOeV
GoPro Hero 9 Black▶ amzn.to/3X0DZTi
Iphone 13 Pro▶ amzn.to/3UUwvzI
Mack's Ultra Soft Foam Earplugs▶ amzn.to/3CDHdUG
Decibel Defense Safety Ear Muffs▶ amzn.to/3Cbkpu6
Solaris Sun Cap▶ amzn.to/3ypa1xO
Scotts Motorcross Goggles▶ amzn.to/3CiW1H6
Swim Goggles, YAKAON Polarized▶ amzn.to/3fNO0SP
RZ Mask M2.5▶ amzn.to/3MiJx70
Equipment I am currently using:
-------------------------------------------------------------
Hour Meter▶ amzn.to/31k2RuG
Echo PAS 2620 ▶ amzn.to/2WCS4qS
Articulating Hedge Trimmer ▶ amzn.to/2TBd8fq
Echo SRM 225 String Trimmer▶ amzn.to/2MRmLV6
Honda HRX 217 Mower▶ amzn.to/2D4t3Mj
Echo PB 8010T Blower▶ amzn.to/2D32bfO
Edger Blades▶ amzn.to/2WaIX0f
Jungle Jims Mower Lift▶ amzn.to/2WjoZR0
DynaplugTire Plug Kit▶ amzn.to/31FDql2
Powertye Ratchet Tie Downs▶ amzn.to/2MpNcSL
Etrack section▶ amzn.to/2s6LhLH
Etrack mount plate▶ amzn.to/35RYjLC
Longacre Oil Filter Cutter▶ amzn.to/2R6Jct4
BigBoyJapaneese Saw▶ amzn.to/2Jzh9Sa
gwinnettlawns.com/

Пікірлер: 56

@jonsheahan3816 6 ай бұрын

I would suggest that you switch to an hour/tachometer and then you can use the tachometer function to adjust your carb settings. What you refer to as a Choke is actually a Fuel Enrichment, it doesn't actually restrict air entering the engine. Also you may find at a certain point that you can't get a good adjustment on the carb and that's because the O ring that holds the jet inside the carb is shot,it is a design flaw of the carb. Have a good day 😊

@GwinnettLawns 6 ай бұрын

Thanks for the info, blower is still running perfect so far.

@ryanb963 8 ай бұрын

The 9010 is definitely the best blower I've ever used thanks for the video

@mitaraho 7 ай бұрын

Thank You for the video, I'm running lean at 44:1 using 110 octane Sunoco ethanol free race fuel and Klotz r-50 oil at 44:1. My old stuff and everything except my new X series trimmers and blowers are running lean (white plugs). I'm thinking 1/4 CCW on the H jets? Or just run 50:1??

@jrodeo96 9 ай бұрын

Thanks for making the video. My 8010 has been doing the exact same thing, and I couldn't figure out why. This is the only video that I have found that mentions adjusting the carb. All of the other videos just tell you to clean the screen on the muffler. I'll have to see if I can find that tool somewhere

@chancemows Жыл бұрын

To avoid buying both lengths of tools, all you need to do is remove the 4 screws that hold the air filter housing, loosen the hose clamp, rotate the housing back and re-tighten hose clamp. You’ll have access to the slow screw and filters will be in place for proper adjustment.

@markjuckett4128 7 ай бұрын

Maybe it was just me but i saw the part numbers for the mixture adjustment tools and all of your links. 👀 I may try the ear muffs because mine are old and will try the swim goggles to keep the dusty crap out of my eyes when mowing. Thanks for all 👍

@glennanderson5335 Жыл бұрын

My PB 770 started acting up the other day. It would crank up and idle but when I gave it throttle it would bog out. I had to let it idle for a little bit before I could throttle it up and then it would need to warm up more before it would get to wide open throttle. Was aggravating

@louiehancock354 11 ай бұрын

Just a little information I have learned. I was having problems with my 9010 so I bought a Chinese after market. It was hard to start and once it did I could tell it was not right. Long story short...bought another carb...but as a kit..hoses, carb, gaskets, etc. 39 dollars. For starters, the Chinese carb has an adjustment that you can use a micro flat head screw driver. Runs great once I richness it up. MUST READ!!! Must use gaskets sent with aftermarket carb...small hole does not line up with OEM gasket.

@GwinnettLawns Жыл бұрын

Not sure why the comments were turned off but now they are back on.

@richardf9137 9 ай бұрын

Never had any issues with mine, I run 40/1 Amsoil Dominator , starts easy at 30 degrees! Good luck!

@Born2doom Ай бұрын

The Blower runs good on 40:1?! I heard Amsoil is pretty good?

@richardf9137 Ай бұрын

@@Born2doom YES

@motion_mx 4 ай бұрын

Just took the carb apart on my 9010t to clean it and it put it back together and it is now totally bogging out. Idles perfect but if pull the throttle it bogs right off the bat. Any ideas?

@1manarmy647 Жыл бұрын

What’s the tool part number that adjusts the carb?

@robertroth1042 Жыл бұрын

Thank you sir where are the links to Amazon for the tools ? I have the same blower. I love it.

@icemanrrc Жыл бұрын

I was also looking for them

@jefffry5250 Жыл бұрын

Do you have the part number for those tools

@timmyl2005 8 ай бұрын

I can’t say that I’ve had a problem with this I will check and see if fattening it up just a little bit makes any difference I run 80/1 98-100 Octane

@bengrooms7694 4 ай бұрын

Anyone know where I can get the short tool ? Can’t find it anywhere

@proulxguyllaume2610 Жыл бұрын

Hey thanks for the video!! Do you have the parts number for those screwdriver. It would help me alot. Thanks

@proulxguyllaume2610 Жыл бұрын

Can you tell me when you have a seconds, does that tool fit your 2620. I am trying to find a tool to adjust my trimmer.

@user-mh8yr2sk5o Жыл бұрын

I don’t see the part numbers for the tools ..??

@so2315 Жыл бұрын

Were there any plastic plugs covering the holes?

@GwinnettLawns Жыл бұрын

Nope

@blademasterlawncare3268 10 ай бұрын

So you have a hour meter on yours, purchase same blower last year , no hr meter. Did you add yours?

@GwinnettLawns 10 ай бұрын

I put an hour meter on every piece of equipment that burns gas. I have the link in the description and I have videos showing how to install them.

@chewarmstrong Жыл бұрын

Any update on the link for the tools? Thanks

@GwinnettLawns Жыл бұрын

They don’t appear to be on Amazon right now, but as soon as they do, I’ll put the link.

@jaydencabral181 Ай бұрын

my 9010 leaks a bit of reddish oil around the carburetor is that normal??

@GwinnettLawns Ай бұрын

Nope not normal.

@Blindlight4029 7 ай бұрын

Thanks but it would have helped to get a good look at the tool and you failed to give the links. When I search on Amazon, I am taken to tool kits and so links would help a lot.. I actually bought a tool kit a few years ago for the chain saw but I can't seem to get a tool to fit in the hole and do the job. Is there a carburetor idle speed bolt apart from the two other adjustments. Mine is running fine except it would idle properly

@GwinnettLawns 7 ай бұрын

The issue is that Amazon does not have the tools on there anymore so no links are available.

@Blindlight4029 7 ай бұрын

I noticed you saying that elsewhere, thanks@@GwinnettLawns

@bbkmm1 8 ай бұрын

Can you use the short tool for both adjustment screws?

@GwinnettLawns 8 ай бұрын

Nope.

@harrislandscapingpa 3 ай бұрын

Yes short micro d works for both high and low on this unit

@jairusbarringer7525 Жыл бұрын

The only thing wrong with your video is that dang dirty bird shirt, ATL vs CAR wk 1 2023.. CAR going 1-0 baby!!! Great tip on these 9010s though, mines doing it to. I bought the long tool but need the short one

@carlosortiz4755 8 ай бұрын

Can you share the link for the adjusting tools please 🙏🏾

@GwinnettLawns 8 ай бұрын

They dont have them on Amazon.

@extremerc76 7 ай бұрын

What hour meter do you run

@GwinnettLawns 7 ай бұрын

I have a link for the hour meter I use down in the description.

@thoreau7 11 ай бұрын

Where is the low idle adjustment? I dont see anything up there. It would have been nice if you would have pointed it out.

@GwinnettLawns 11 ай бұрын

I did point it out with my finger twice. I showed and even said you have to do it by feel because you can’t see it. The only way I could have showed the screw was to remove the carburetor and have a camera that could zoom in really tight. You’re just gonna have to trust me and do it like I told you on the video because I can’t even see the screw when the carburetor is on the blower. You have to do it by feel.

@thoreau7 11 ай бұрын

@GwinnettLawns ok...i cleaned the dirt away from it and saw it. Thanks