ENGINE IS COMPLETE! Puch Maxi e50 Polini 64cc install

Рет қаралды 31,234

Жыл бұрын

We threw together the complete engine build for the puch maxi! Ported the polini cylinder, tossed some bearings and a crank in & slapped the cases together. Shes almost ready to fire up!
-
NEW #MOPBOYZ GEAR OUT NOW!!! : www.mopboyz.com/
-
NEED SCOOTER PARTS? USE CODE " MOPBOYZ " and SAVE $:
scooterswapshop.com/?ref=MOPBOYZ

Пікірлер: 49

@FrankRommerts-dr4yp 8 ай бұрын

That hole from the exhaustport to the cylinder deck is for a decompression valve in the head, but its also great for an exhaust temperature probe.

@hustenbursche58 Жыл бұрын

man i got a own puch maxi. i got it since i was 7years. i completle rebuilded it a few months ago. Love to see people are rebuilding this mofa. Best greetings from Germany ✌

@henkjeoma8069 Жыл бұрын

Love seeing Americans giving scooters/mopeds some love. Btw your pronouncing Puch wrong it's a softer g kinda like the ch in cheese not trying to hate just trying to educate.

@Ocymber Жыл бұрын

Are you Dutch

@henkjeoma8069 Жыл бұрын

@@Ocymber yes

@Ocymber Жыл бұрын

@@henkjeoma8069 ik ook

@bainislavas116 Жыл бұрын

always fun to watch an engine build, even more fun to watch an engine you havent seen before

@Tristan434 Жыл бұрын

Mob boys package just arrived. Let’s go.

@Niels-booij Жыл бұрын

I did the same thing with my tomos i also have a big intake that goes sideways with a polini membrane i just drilled 2 little holes where the screws sit deep enough to sit flush

@BobErkle Жыл бұрын

Your buddy absolutely murdered your friends haircut haircut

@1LADA3 Жыл бұрын

never seen a 64cc motor... keep up the good work..

@andyproctor3588 Жыл бұрын

Ya man can't wait been watching the progress of this I got to see how this thing is going to go thanks y'all waving my hand from down here in gville Florida

@retrosmoke Жыл бұрын

Sick work!

@metrashit Жыл бұрын

Hole is for the really old decompression valve engines found on the earliest Puchies.

@benwhitford5703 Жыл бұрын

It would be sick to put a 140cc pit bike engine in one of these

@truethought369 Жыл бұрын

Golden rule: Never use sealant on head gaskets! Reface head, & crank case. Use a new gasket lightly oiled. I like the porting, it's all about breathing. You will get about 20% more power if right.

@alvin-kq6mh Жыл бұрын

Great vid keep it up 👍🏾

@andyanders58 Жыл бұрын

Great job. For not doing one before. I say 3rd kick it starts how about it followers old man mop

@cav3man360 Жыл бұрын

About to have my China bike up and running for the summer this week mopboyz mobbing

@im_miky9952 Жыл бұрын

Nice video bro 👍

@Jack-ct7gg Жыл бұрын

Sick build🔥 Used to rock the polini the best upgrade you can do to it is get the better reeds I think 4 paddle. The oem reeds on it aren’t the best.

@dopechaincobain2828 Жыл бұрын

Yo Trev! Peep would want for me to come out and learn a few things from you! Bro let me come hang for a few days and help me get 2 of my projects moving. I’ll stay at a hotel near by lol. No stupid shit going on here on my end. Strait up dude frfr.

@mikesbarn1858 3 ай бұрын

Nice build. Did you balance the crank? My son and I took a cheap kit and cut the crank case out and made an intake manifold to mount on it. It’s a beast pulling into the case.

@bassbustingman Жыл бұрын

de compression hole not sure if that head will work with that hole gasket on head might be not sealing the hole?

@amko_1312 Жыл бұрын

Nice but that 21mm i think is too much for that set up is okay 16/16 dellorto or max 17,5

@mandel4889 6 ай бұрын

the hole in the cylinder is for decompression i think. helps with the pedal start.

@dyabi8468 Жыл бұрын

Can you please do a tutorial on how to do knee knockers and standups on a 50cc scooter it would be very helpful

@klaas4034 Жыл бұрын

Where did you get the odi grips from and are these only the grips or is that with the tubes

@AKYLE315 10 ай бұрын

i would have shaved the screws and put lock tight on them for that piece that went into the block instead of creating notches for them

@Oneway_Sting Жыл бұрын

W! PUCHBOYZ

@Mitch_017 Жыл бұрын

Does anyone know what jet and variator to use on a 1987 Honda elite with a MLM pipe

@sunsky469 9 ай бұрын

I see that in n out tray 😂 i use the same tray to hold my hardware

@dennisdebengel1989 Жыл бұрын

the little hole in the cillinder is for decompresor. old way to turn of the bike.the normale head has valve when open u have no compresion.sry bad eng

@Ocymber Жыл бұрын

Are you Dutch

@juanito3564 10 ай бұрын

Yo i have a question, what is that helmet from the intro called? Bc i want to get one

@tomkranenonk3163 Жыл бұрын

hey man, got a question. Ive just bought a phantom f12 but the front suspension broke, i cant find any that fit. Which forks do fit on a malaguti phantom f12 ? (anyone who knows lmk)

@FluidX08 Жыл бұрын

What helmet do you have?

@camraider7728 Жыл бұрын

One of those in my poppops basement lol

@tangoalpha8381 Жыл бұрын

👍🏆🇧🇷 all the best

@apox_ 8 ай бұрын

jou nedd a italkit 74cc

@515.Outdoors Жыл бұрын

are you in the us or different countrie?

@MOPBOYZ Жыл бұрын

usa

@sennegovers9448 Жыл бұрын

The hole is for a decompression valve to stop the engine

@toandiy7127 Жыл бұрын

Hello.❤

@gb.recordings 11 ай бұрын

How much would you charge me to build me a bike like that one right there I want to be doing wheelies on it cuz I live in New York City I want to get it registered and have fun with it please get back to me