How To Replace Drum Brake Shoes (Full)

How To Replace Drum Brake Shoes (Full) - EricTheCarGuy

Рет қаралды 2,799,484

Күн бұрын

How To Replace Drum Brake Shoes (Full) - EricTheCarGuy
www.ericthecarguy.com/
Here is a full length version of a video that I posted some time ago, this way you can watch the entire thing in one sitting instead of switching from one video to the next. If your watching this for the first time I'm aware that sandals are not the best thing to wear when doing auto repair. In addition there IS a jack stand just out of frame in the video I just leave the floor jack in place while I work normally where it is so that it's quicker to let the car down when I'm done.
---
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
ericthecarguy.com/
Visit EricTheCarGuy Forum
www.ericthecarguy.com/forum/de...
Visit my Facebook Page:
/ ericthecarguy
---
Stay dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

Пікірлер: 1 200

@jasonlong4071 4 жыл бұрын

"Milestone of 100 Subs" I'm watching this vid 8 years later, and you have over 1million Subscribers. Congrats man, and thanks for your vids.

@elitehedhunter-4017 4 жыл бұрын

Same

@getin-light-ened6954 3 жыл бұрын

Same...10yrs ago...hes jst shy of 1.6m ;) congrats Eric 👏

@Charles-cb3lo 2 жыл бұрын

Nearly 1.7m today 🤩

@Charles-cb3lo 2 жыл бұрын

To be fair back then, 100 subs was honestly a respectable amount

@sbfguy7793 5 жыл бұрын

Now at 1.3 MILLION Subscribers....... Well deserved man, well deserved.

@spencemcmorris7686 2 жыл бұрын

I never seen this video till today buddy and your already and have been for a year or so one of my go to guys for car repair tips and advice. Keep crushing it and remember the number of subscribers and comments you have today do not reflect the amount of people you have helped currently or will help in years to come. Thank you Erick for your time.

@Nalopotato 8 жыл бұрын

"Milestone of 100 Subscribers" LOL. Thanks for the upload

@dadudesandstorm9582 5 жыл бұрын

Made me lol

@timanderson9466 8 жыл бұрын

Watched a million how to videos and after watching your video I understand why you have the subscribers you have. Your video/s are direct and to the point and you explain so a person can understand how and why during your vid. Explain the parts as they come off of what they do and the importance of properly re installing. Great job dude!!!!!!!!

@jeffbaker4364 9 жыл бұрын

I am a mechanic and the entire job was spot on. All you fucken knockers out there are pissed off you cant do your own. Good job Eric, all the best from australia.

@473nelson 6 жыл бұрын

Jeff Baker wise words of inspiration!

@donaldhollums3278 4 жыл бұрын

I'm watching this film almost 9 years later, Eric. Your channel was the first automotive based one I subscribed to three years ago when I started doing my part time automotive repair work. Since then I subscribe only to automotive experts like yourself for tips and the correct ways of doing my repairs. I've been more of an automotive DIYer all my adult life and I really don't want repair advice from another DIYer especially when I'm working on some one else's car. I'm sure 100 subscribers seems like a lifetime ago, huh? Keep up the great work!

@joederochemont6219 4 жыл бұрын

Once again Eric, you completely show me what I need to know to get the job done. Backyard mechanic, 07 Chrysler Sebring with rear drum brakes. Thank you so much sir!

@ajs622 8 жыл бұрын

Awesome video Eric, I've been doing my own drum brakes for years, there were a few things I learned from this video that I will apply to future brake jobs thanks, keep up the great work.

@berylbarker2255 8 жыл бұрын

Eric, I found a much easier way to adjust rear brake drums! Start your car put in reverse and while reversing pull the hand brake while moving. The self adjuster does both sets of brakes for you. And there is no guessing whether they are both adjusted the same as they will stop adjust either brake when it gets to the required tolerance...

@danbytp 7 жыл бұрын

You know,you are the first guy in my 30 years of dyi auto stuff who adequately explained this to me.Thank you,sir!😀

@robertmorena9549 10 жыл бұрын

The ONLY time I attempt to work on my car when it comes to DIY mechanic things, tune-ups, suspension parts, brakes etc. I watch ERICTHECARGUY every single time. You are awesome Eric, thanks for all your hard work and dedication in your videos.

@satguy27 7 жыл бұрын

I tried to see if this was in the comments but didn't see it. On the spring release tool, it helps if you use either some silicone grease or even axle grease on the stem of the tool, especially during reinstallation of the springs. It prevents the friction of the hook on the stem during reinstalling the return springs and less likely to damage your fingers/knuckles. Hopefully this helps someone out...

@ShermanT.Potter 7 жыл бұрын

I'm by no means an expert but I found that using vise grips on the straight portion of the top springs works quite well. Engage at 90 degrees to the spring and pull towards the spring post. It takes strong hands and wrists (and a good bite with the vise grips) but it's fast, and there's nothing on the spring end getting in the way. :)

@davidmiracle398 3 жыл бұрын

Thanks for this good video. I'm 83 and about to start replacing the rear drum brakes on my old 1978 Dodge Colt 4 door sedan. I've replaced brakes on other cars during my lifetime, but your video refreshes my memory of how to do the job correctly. Much thanks.

@ericthecarguy 12 жыл бұрын

@mastmanageangelatsui You are most welcome, thank you for your comment.

@kangthumper2185 8 жыл бұрын

Wow… This was back when you had 100 viewers? Love this channel;

@19aas95 9 жыл бұрын

Wow! In less than 4 years he went from 100 subscribers to 540k subscribers!

@edyue1 5 жыл бұрын

1.3M diam

@BestVideos01 4 жыл бұрын

Now more than 1 m

@ciphergalm1174 5 ай бұрын

12 years 2.7 million

@ericthecarguy 12 жыл бұрын

@Zig23482 You're adjusting the clearance between the brake shoes and the inside of the drum. You need to do this to ensure good brake pedal feel as well as not getting them too tight so that the brakes overheat and possibly lock up.

@klmartin1962 10 жыл бұрын

Great job. You are the first person I have seen on here who talked about primary and secondary shoes. Most act like all 4 shoes are the same. Good job.

@encee2016 8 жыл бұрын

100 subscribers? Rising through the ranks to 700,000. Will subscribe, gotta respect that.

@MindOverEverything 9 жыл бұрын

100 subs in 2011. 4 years later, 616,000 subs. Nice.

@Patrick94GSR 8 жыл бұрын

+MindOverEverything And now up to nearly 671K!

@MindOverEverything 8 жыл бұрын

+Patrick94GSR He'll probably hit a million in another year. Totally deserves it. Between him, Chris and "Nuts" I can find 95% of what I need.

@Nightowlz17 8 жыл бұрын

+MindOverEverything AND NOW ALMOST 700K

@thatsmyblanket9570 8 жыл бұрын

350k clock sufferer usual, mop. Roulette unused pegboard.

@DjayLSD 8 жыл бұрын

+MindOverEverything And Already 715,509 as of january 10 2016 ^_^

@christiantischer68 9 жыл бұрын

EricTheCarGuy I love how in the beginning of this video you were excited about 100 subscribers and now you have 600k. Way to go Eric!!

@emmaharris2952 7 жыл бұрын

"Leggo my Eggo." LOL Really appreciate you taking the time to share this. I was actually searching for a how-to on removing the drum itself, as I would like to be able to blow out the inner workings of the drum brakes to remove dust and debris build-up. Thanks!

@DavidLorellHoskins 8 жыл бұрын

Eric The Car Guy, you're one awesome dude. Thank you so much.

@metaphysicaudio 4 жыл бұрын

“Alright now it’s time for the shoes...” nice flip flops Eric hahah.

@Stevie_B_0828 3 жыл бұрын

IKR, But I think they're Teva's. 😉👍

@jdubyaadams170 10 жыл бұрын

Mr Eric, thank ya sir, your video took the unknown out of doing this job for my son. He learned that no springs were gonna pop out when he took the drum off his car. Thanks brother!

@joby613 10 жыл бұрын

Exactly how I do it for drum brakes, except ALL metal to metal contact surfaces get nickel or copper antisieze, and I clean my grubby fingerprints off the brake linings before final drum installation. Also, I do several hard braking in reverse prior to delivery to the customer before my final test drive to affirm that the rear shoes are fully self adjusted. Thanks, E for yet another informative and insightful vid!

@mdmjwarner 8 жыл бұрын

Are those sandals OSHA approved?

@juliomv7664 7 жыл бұрын

lol

@sheriethomas9931 7 жыл бұрын

Chinese safety boots..

@hansen666 7 жыл бұрын

Sherie Thomas nipper slippers

@DjJtown 6 жыл бұрын

They're comfort approved and That's what counts. BTW speaking of count; count your toes after doing it. haha

@dadudesandstorm9582 5 жыл бұрын

*OSHA INTENSIFIES*

@sh1tlord907 8 жыл бұрын

Speakin' of shoes, nice sandals, dog. Proper attire for automotive repair indeed.

@mr.nobody9630 7 жыл бұрын

You are one hell of a teacher....Eric, I was reading a book today about how to do this, of course, I didn't learn a darn thing from reading it...This video is far more helpful....Many thanks just need to practice going to the junk yard this coming weekend.

@jakubhryniewicz5321 5 жыл бұрын

I did this in my high school shop class on and early 80s chevy...never dreamed that my 04 accord would have them. WTF! Thanks Eric for a good refresher course!!!!

@spiffcats 8 жыл бұрын

I hate drum brakes. Probably because I had the emergancy brake on while attempting to get the drum off. Yes, I am an idiot.

@Riaining7 8 жыл бұрын

+spiffcats This is how we learn. Imagine the trouble this comment might be saving some person who read it. :)

@MrBilld75 6 жыл бұрын

Rianing has a point. Even though you had the e-brake on when you did it, your comment may help others. There is a bright side and you are not an idiot. I almost did it once. Then when I thought about what I had done, I thought "Wait a sec. Wouldn't the e-brake being applied, because it affects the rears, make the drum harder to get off?" So, I released it. No shame in what you did. I think all us amateurs have made similar blunders. I know I have. Lol.

@Simone9937 6 жыл бұрын

spiffcats You just saved me an hour or two probably figuring that out. Thank you!! ;) Seriously! I'm on my own here. lol

@MrBilld75 6 жыл бұрын

There we go! Proof that his comment. just saved someone a headache and he isn't an idiot. Just like we said it might.

@travisrosenberry3472 6 жыл бұрын

You are not alone. I had to go through the same thing. LOL!

@PandaMan02 7 жыл бұрын

i wish they outlawed drum brakes because of how much time they take.

@randomvideosn0where 4 жыл бұрын

Don't ask for dumb laws, your choice of what to buy/work on

@TheRakuman 8 жыл бұрын

Eric, it's been many years since I've replaced drum brakes on one of my vehicles. This was just what I needed. Well done video and clearly explained along with some nice lube tips to keep things moving as they should. Thanks! You've gained another subscriber.

@JasonLee-sw6df 11 жыл бұрын

This video was amazing. You gave a non-mechanical person, such as myself, the confidence and knowledge to achieve my goal of changing my own drum brakes. saving me 150 dollars from a mechanic, without taking a whole lot of time out of my busy life. Thanks again Eric!

@EricOverOnYT 9 жыл бұрын

Hey, nice name! Didn't know who EricTheCarGuy was when I made my channel

@billcaspole1539 7 жыл бұрын

Eric, great videos. I tech Auto tech and have a few suggestions: Before starting : Be sure to wear safety glasses. Work boots or shoes instead of sandals. I see no safety jack stands for safety. Other than that you have done a great job!

@MrBilld75 6 жыл бұрын

There is a jack stand almost out of the sht at one point and in his other vids, he surely does recommend the use of jack stands. I've had a car fall of the jack (not while under it however and I never would), so now I use them religiously, no matter what job I do and I back them up with cinder blocks too. Safety glasses are a good idea, when working with strong springs like this and brake cleaner too and even a mask should be used with brake cleaner, but I don't use them either, lol.

@SR-cp1eo 9 жыл бұрын

I watched this video before I replaced mine on my 99 k2500 suburban. Ive never seen shoes that big before but this video made it simple. Lost a bit of blood but I never forgot what I was doing. Thank you for your detailed videos!

@Lilmiket1000 11 жыл бұрын

Dude u make the best videos!!! Ive done so many DIY projects and saved sooooo much money just watching you show me how to do stuff. one of the main ones you taught me was how to change a front and rear wheel bearing on my 99 Jeep Grand cherokee. I took one side in to the shop they charged me 200 something and put it in backwards. I done the other side myself. and had to redo the side the shop done. Thank you so much!

@MrSuperMation 8 жыл бұрын

I liked the safety sandals. :-)

@generichombre6976 8 жыл бұрын

I'm not looking forward in doing this

@Dagrond 2 жыл бұрын

1.6 Million subs, for a humble guy who was happy with 100. Thanks for all the help over the years!

@harrycallahan5944 9 жыл бұрын

eric My father owned and still owns a shop I grew up in that shop. Your video was very good. You didn't ef up at all with your instructions. way to go man

@DaCoder 10 жыл бұрын

How could drum brakes cost less to manuf. when disc's are so much simpler?

@xxRamD3yruxx 9 жыл бұрын

Sean Slater because caliper castings are an intricate part requiring machine work, drums and stamped components still come out cheaper

@robertweeks7993 10 жыл бұрын

goddamn i hate drum brakes lol

@edyue1 5 жыл бұрын

government needs to ban them

@fck45 5 жыл бұрын

lmao......same here but they are great when they are new and gripping!

@AdrenalineRushMX 4 жыл бұрын

@@fck45 just swap it

@tbpom1003 4 жыл бұрын

I watched this video about 8 years ago. I just purchased a used prius which the rear brakes are drum. finally time to use this tip lol Thanks Eric! oh, and milestone to 100 sub is the most hilarious part of the vid lol

@McGuigan21 5 жыл бұрын

Just looking back. What an accomplishment you've achieved. As I write this, you're at 1.2 million subscribers, just a touch more than the 100 in this video.

@Bombastic_Spastic 8 жыл бұрын

Didn't know you could get steel toe cap sandals lol

@laurensstijnenbosch 8 жыл бұрын

Nice Indian safety shoes!

@NoSuffix 4 жыл бұрын

I thought I heard it wrong - "100 subs"? Then realized this is 9 years ago. Wow, almost 1.5M! Nice & congrats, Eric!

@chasedixon6090 9 жыл бұрын

I know this video is old but it was very helpful to me. I'm 16 and still learning new things everyday about how to properly work on my truck. This video was so much more helpful than the diagram that the manual had. Thank you so much for this lesson.

@griffnut666 9 жыл бұрын

Drum Brakes suck- Good video

@YourMajesticKyng 8 жыл бұрын

+The Real Slim Shady Because they keep manufacturing costs down.

@griffnut666 8 жыл бұрын

What I meant was , they suck to fix.

@YourMajesticKyng 8 жыл бұрын

+Wayne G They do suck to fix indeed.

@141MusicLove 8 жыл бұрын

+Wayne G I understood what you meant, they do suck to fix up lol

@Texassince1836 8 жыл бұрын

+Wayne G I put the drum brakes on my truck one night after I got off, in the dark... they're not that bad

@bobcashflow50 10 жыл бұрын

Is it me or drums brakes are stupidly complicated and ineffective compared to disk brakes wich only have 4 bolt for disassembly ?

@dchawk81 10 жыл бұрын

Nah it's not just you. I hate them.

@annwashington1541 7 жыл бұрын

Thierry Dubuc me too its the worst to deal with

@bruceblackwell743 7 жыл бұрын

NO JOKE ABOUT THAT THIERRY I can change a million disk blind folded

@jason4832 6 жыл бұрын

Discs are way easier to service but drums handle weight better than discs

@MrBilld75 6 жыл бұрын

Yes, they are stupidly complicated and I hate them as much as everyone else does. However, they are cheaper to manufacture and service.

@ericthecarguy 12 жыл бұрын

@m0t0cr0ss17 If you suspect warped drums or brake discs have them measured, if there is enough material left you can often machine them true again instead of replacing them.

@ryana6836 9 жыл бұрын

+EricTheCarGuy Eric- thanks for all of your videos. About 1 to 2 years ago I could barely do an oil change. With the help of your videos I just completed a full drum brake restoration with new brake lines in my 77 Malibu. Also did new shocks, radiator, thermostat, sending unit for gas gauge, and carburetor. You have quality videos and instruction. Nice work and thanks.

@traviswatson4986 9 жыл бұрын

the sandals eric... the sandals...

@flinch622 4 жыл бұрын

Margaritaville mechanic...

@LJRossPhoto 10 жыл бұрын

*100 subscribers *Checks sub count *Has 472,983 subs

@pmkleinp 10 жыл бұрын

He's added over 5.400 subscribers in just one week.

@j.a.b.9976 4 жыл бұрын

100 subscribers when he was very new to KZfaq, Now Eric is getting ready to hit 1.5 million. Very cool and congratulations!

@ericthecarguy 12 жыл бұрын

@Platinumkanikas Thanks for your comment and sub I really appreciate them both.

@KFORVET 11 жыл бұрын

Eric, thanks for a great series of videos. I'm a shade tree mechanic and have had to learn too much by trial and error. It is a hell of a lot easier to watch a video and then go to the job. Keep it up, and thanks again!

@GUANACO84321 12 жыл бұрын

ERIC, I'VE BEEN WATCHING YOUR HELPFULL VIDEOS, WHEN I HAVE SOMETHING TO FIX ON MY CAR OR MY FRIEND'S CAR, I JUST SAY "I'LL GET HELP FROM ERIC", THANK YOU SO MUCH FOR YOUR TIME AND EXPERINCE, A LOT OF PEOPLE HAVE SAVED MONEY JUST LEARNING HOW TO DO CAR SERVICES BY THEM SELVES 'I AM ONE OF THOSE" THANKS AGAIN!!

@pneumann4195 9 жыл бұрын

Eric TCG. Just wanted to say thanks! While replacing my drumig brakes and having had a hard time trying to get the top spring on (last step of sequence) I saw you using a screw driver to leverage and slide over the spring. My needle nose grip and pull was impossible. After seeing your video I used an longer allen key to leverage and slide over the spring. Done! Saved my ass.. Thank you. I used elastic bands (broccolli) to hold the shoes down before the spring loaded clamps were on. Not sure if that helps anyone.

@samitchdog 7 жыл бұрын

You have been very helpful in posting videos like these. I have done practically all work to my 94 van and 85 suburban myself. You sir are a beast and I love this channel always something useful to learn. Thanks for all the videos and posting so much content. Regards, Willie

@billbowers2805 8 жыл бұрын

Hey, Eric- nice video - I'm doing the rear drum brakes on a 88 Ford Crown Vic (10"0. It's a little different than this, but I like how you show both shoes going in, with the self adjuster and spring intact. (I've fought some terrible battles with that spring by putting it in last). My problem is the right side front shoe wears out WAY early and all three other shoes have lots left on them . A buddy told me to check the parking brake cable for not holding down. Thanks again! Bill

@IAmSidTheRealKid 7 жыл бұрын

Wow 100 subscribers... Now you have 864,371 subscribers. You have come a long way. I've watched you from the start and your videos have become very useful and handy. Thank you! You videos have made me purse an automotive career.

@Lesscoelectronics 9 жыл бұрын

Tell me, what camera do you use to get such clear images, my videos are no way as crisp.

@rachaelbrown7817 11 жыл бұрын

I just got done replacing mine. The first one took two hrs ,-), but once i got it down, my passenger side was done in 45 min. I just want to say thank you for the great video and information. I def. needed all the money i just saved.

@JoeVidal1970 8 жыл бұрын

Aw dude! You made this so simple. I had tried before taking pictures and failed. This is what I needed! Thanks EricTheCarGuy!

@rusticswag 11 жыл бұрын

I just did my friends breaks but I wanted to make sure I did them right so I used your video as a reference. Your channel has always been a big help. Thank you very much.

@Cmartelli 12 жыл бұрын

Eric. Your my hero. Working on your car in sandals..... Personally I wear my slippers. ( Kid's, do not do this at home ). And I thought I was the only one who did things like this. :) Thanks for posting this job on brakes. Very helpful.

@patrickdriscoll9962 9 жыл бұрын

excellent....plenty of helpful details; thank you. Eric I have switched to the blue Nitrile XL gloves from the nurses latex type gloves you are wearing here..... the blue Nitrile do not tear

@jgeobert1399 12 жыл бұрын

I like the video and it is good to see someone trying to help out those who are not mechanically inclined, but wish to save money by doing repairs at home. The only issue I have with this video is the touching the lining surface of the shoes and getting them greasy...that could cause fade. Thanks for the videos, keep them coming!

@BobBarkerBich 12 жыл бұрын

@ EricTheCarGuy ...not doing drum brakes in over 10yrs. I had no spring tools. After watching your video briefly, I "maned-up" and took apart the drums n shoes n springs. Have leaked for sometime and looks like black mud covered everything. I will be replacing the cylinder as i believe that is the issue but the shoes themselves were looooose and I never had an ebrake sense owned the truck. Never looked at brakes before but now fluid resevuor level drops quick in both F and R. Your video rocks!!

@jaguiar45 5 жыл бұрын

I just changed my drum brakes and I didn't have to look at the repair manual I just looked at your video. Your videos are great.

@LaZerMouse 2 жыл бұрын

Awesome job Eric and thank you. I used silver anti-seized on one of the adjuster wheel and the other side I used brake grease. I sure hope it works ok. I didn’t have copper anti-seize.

@riverbendcedar 9 жыл бұрын

Planning my first rear brake shoe change. The video is great....several things that I had not thought about like the lub on the bake plate boses and adjuster plus the difference in front and back shoes. Eric, great job.

@moonshinerman 6 жыл бұрын

Great video. I used to get a pair of pliers and close the spring end loops up slightly because as you take the springs off the end spreads open. Close them to normal and the springs will have less tendency to pop off.

@slightleeaddicted9415 5 жыл бұрын

I was in a jail for 30 days and watched erics videos while in there and was able to diagnose my pcv valve hose which had a bad vacuum leak that i fixed. This dude rocks lol years later im still watching his videos on KZfaq

@montydaniels1054 7 жыл бұрын

Wow, 100 Subscribers! I see that you've picked up a few more since this video. I do enjoy watching your video's & trust your knowledge with automobiles. I need to replace the rear drums & shoes on the 1998 Honda Accord that we gave our grandson back in 2015. Still drives like new with 190K as of last week. So you may be getting lots of questions from me since we've done about 98% of our own work. Keep up the good work Eric.....

@ericthecarguy 12 жыл бұрын

@re3rocks69 You're right, this was an early video and at the time I made it I wasn't thinking of such things because I had no idea ETCG would grow into what it is today. Thanks for keeping me honest.

@AeroSS87 Жыл бұрын

A hundred whole subscribers! Lol man, things have sure changed. Glad to see how much your channel has grown.

@gerrycummins7176 4 жыл бұрын

One hundred subscribers! Wow this was whatever 1.2 million subscribers minus a hundred ago. Congrats and I watch a lot of your videos as they’re super helpful. Thanks Eric

@YouTubebingewatcher 9 жыл бұрын

100 subscribers to 600 thousand, bet you didn't know how much people love ya.

@GSG834129 11 ай бұрын

Excellent video Eric, I've done my drum brakes on my 1969 chevelle before but its been a long time so this helps immensely! Subscribed.

@crossroadadventures 11 жыл бұрын

I've been doing disc brakes all the time..after watching this video and purchasing the all in one tool from NAPA, I'm ready to do brake drums.. Thanks Eric for a wonderful tutorial.. This will definitely help in doing 97 RAV4.

@edyue1 5 жыл бұрын

Jack stands optional...haha awesome video! Thanks ECG, I only change these every 5 yrs and I totally forget what order to remove the springs/parts and reassembly is a nightmare! Now I know how to use that ridiculous tool that I bought but never used (ie screw drivers, pliers etc in the past).

@tilmonhensley443 4 жыл бұрын

Hey ERIC,, you are one of the best ive seen on youtube, No ones perfect, Please dont put your self down, You are pretty good for a young whiper snapper, keep on smileing, old man frm north carolina.

@SecularAdvocate 11 жыл бұрын

First off, great video, thanks. When I was taught to adjust brakes after installing new, I put the wheel back on, spun the wheel while tightening the star-adjuster from the access hole on the back side until the wheel would no longer spin, then loosen until it freed. You could still hear the breaks touching but that would stop after the first or second application of the brakes. I also cleaned the pads before replacing the wheel, as you did with the drum.

@jeffnewman6429 11 жыл бұрын

It's been a long time since I've replaced brakes. This video on changing drum brakes was extremely helpful and the job went without a hitch. Thanks!

@ranger178 2 жыл бұрын

i missed this video when i did my daughters 2007 honda civic and was looking for brake drums on a civic i have the same tools you have there and never knew how to get the springs back on with that tool they need an instruction manual with that thing lol i had those tools for 35 years and still don't know what end to use on which springs. I am glad most cars are disk now

@canarychick7688 9 жыл бұрын

Eric, you are a thorough instructor. I have used your videos to replace my rear brakes. Thanks

@jimmyismealright 8 жыл бұрын

thank you so much for the vid. I haven't changed brake shoes since auto class over 10yrs ago lol I saved so much money doing it myself

@matt8787fat 9 жыл бұрын

I think this is really going to help me this friday when i do the rear drums on my 77 Olds it will be the first time i have done drums so thank you for the helpful video.

@OpaKnows 11 жыл бұрын

For me, THE BEST descriptive video I could find on how to do the brake shoes on my 2000 Dodge Caravan. Thank you, Eric. I'll probably have this on a loop beside me as I replace them later this week!

@JFreakinWet 10 жыл бұрын

I see why your channel grew so well, excellent stuff right from the start.

@John3965 11 жыл бұрын

Very informative. Last time I tried this here in 1991 on a Pinto, the whole rear brake system fell out as soon as I took the drum off. I can do front brake very well. Been scared to do back brakes. But checkin this out. I might be on the roll again.

@jayarscintilla 11 жыл бұрын

i was watching some other mechanical vids and found myself falling asleep. I knew your humor and skill would keep my attention. Fantastic as usual

@denislangley5558 8 жыл бұрын

Great video...thank you! I tried this before and found it was useful to take a photo before I started to show where all the springs hooked into. Then, if I got stuck, all I had to do was go back to the photo on my laptop. Easy!!!

@jonny1943 12 жыл бұрын

Sweet! that helped ALOT! My brakes from 97 were a little bit different in construction and that a couple of springs were missing in the parts package really got me puzzled for a while. Thanks!