How to Change Rear Brake Discs & Pads
Рет қаралды 153,691
11 жыл бұрынBrake pads consist of a backing plate and friction material. It is the friction material that comes into contact with the brake disc. Overtime the friction material wears down and your brakes become less effective at stopping your vehicle. The manufacturer of your vehicle will specify a minimum thickness of the friction material before the brake pads need to be replaced.
Find the right part for your car here: www.eurocarparts.com/
@andrewcross2116 7 жыл бұрын
Useful video. In addition to glasses when wire brushing, cleaning/wiping gloves to remove oily residues before handling the new brake disks / pads is also a good idea.
@leebennett3672 Жыл бұрын
Excellent video thanks for posting
@JamesLangUK 10 жыл бұрын
Liked it, it was very informative, not sure if my motor a 2004 plate honda civic has the same rear set up and needs the wind back tool or not, possibly it does, a bit more clarity on how the wind back tool is used would help. Possibly a bit OTT from me but a dust mask while using the wire brush to clean off old break dust might help the lungs if you do this a lot. All in all I learned a lot thanks
@mohdnasirsalleh5056 8 жыл бұрын
Good job bro..clear pic and details..
@lamarchedutemps7427 13 күн бұрын
Well done Guys !
@Vintaronica 4 жыл бұрын
Where do my get my pianist from, can I have someone use a keyboard to play the tune when I change the brakes, or will that not work?
@GCJNash 7 жыл бұрын
I used an old tap with a big washer to wind back the calliper.
@leebennett3672 Жыл бұрын
Would grips be able to be used instead of wind back tool
@mohmd1933 8 жыл бұрын
good
@spitfire12able 10 жыл бұрын
Good information but you forgot the most important part of put the wheel back on and that is to torque the up to manufacture data
@rickhctep1503 8 жыл бұрын
+Thomas Just what I was thinking.
@tomsnobes2147 Жыл бұрын
When I reassemble these parts, I always apply a very thin smear of grease to all the screw-threads, the faces and the heads of the nuts. It stops what's called "gauling" (thread damage). Remember, in a couple of years you may need to do this job again, so this will help you get the screws undone without damage. Use your common sense and don't get grease on the discs.
@dotmanmide Жыл бұрын
It was advised on another video to use tread tightening to avoid loosening later, which makes sense. Can you use grease as you suggested as well?
@tomsnobes2147 Жыл бұрын
@@dotmanmide The point I'm making is trying to stop the threads rusting (fusing) together over time. Thread compound can do that too but make sure you get some on the bolt faces too.
@paintinout3709 4 ай бұрын
They do it so you go change you discs every time and than . Brake discs are stronger than you thing no need to change when the manufacturer says
@sergd7885 3 жыл бұрын
ĺ
@beboploo 8 жыл бұрын
someones been had off no need to replace them parts at all
@AlexGreenwoodUkulele 3 жыл бұрын
Excuse me, look at those discs and how tight those pads were in the carriers and tell me again that they don't need replacing at all.
@samrodrigues3199 8 жыл бұрын
Anybody else get an ad of this very video?
@DuaynSparks 7 ай бұрын
Very crazy doesn't show what he's doing
@beboploo 8 жыл бұрын
did you no wd40 is made up of 80% fish oil yes thats true
@chris77777777ify 5 жыл бұрын
Wd40 will destroy rubber. Brake cleaner should be used on brakes dummy
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 4,3 МЛН
ScrewsNutsAndBolts
Рет қаралды 338 М.
DIY Khan
Рет қаралды 37 М.
GS PACKER
Рет қаралды 785 М.
EXiAN BATMAN / Dont Touch My Bike
Рет қаралды 15 МЛН
BossHorn - Train Horns with Remote Control
Рет қаралды 148 МЛН
Crafts people
Рет қаралды 3,9 МЛН