Everlast Lightning MTS 275 Review: AC/DC TIG
Рет қаралды 80,113
4 жыл бұрынToday we are going through the functions and capabilities of the new Everlast Lightning MTS 275 Multiprocess welder. Our objective was to test the low lab amp capabilities of the machine and go through the different pulse options and AC frequency capabilities. Prior to the video, we went through the different processes the machine is capable of running and and got familiar with the settings.
We started off doing some razor blades to test out the low amp arc initiation, we got dialed in at 40 amps and welded a set together just to see how well it would perform. Overall, it welded great with the lower amps, We then set up some 16ga. stainless steel and checked out the pulse functions.
For our initial test, we ran 1 pulse per second on an outside corner joint, the machine performed well, but due to the low pulse setting I had to run a bit slower than I would have liked to. The slower travel speed caused a higher heat input which caused some sugaring on the back of the weld joint. This is no fault of the machine, I just think 1 pulse per second would be better suited for thicker material. We then jumped up to 75 pulses per second and I was really impressed with the way that it functioned. I was able to run faster where I normally would on stainless and there was no sugaring on the backside like we had on the 1 pulse per second. The weld turned out very well and we decided to go ahead and max out the pulse settings and see what 150 pulses per second would do for us. The User Interface of the Lightning MTS is pretty intuitive, your major settings are all listed on one screen so you don't have to go around looking for sub menus to make adjustments. There are a couple sub menus in the system but they are easy to access and are items you really don't have to adjust frequently like whether you intend to use lift arc, High Frequency etc. We went back into the menu and ran the pulse to maximum (150Hz.) Once again, the arc initiation was very stable and the machined performed well yet again.
With the low amp stainless out of the way, we set up an outside corner joint with some 16ga. aluminum to test the frequency capabilities of the Lightning. I decided that 60Hz. would be a good place to start because most rectifiers run on 60Hz. At 60Hz the weld turned out okay for the most part but the bead was a little too wide for the joint we were running. Once we stepped up to 120Hz. the bead profile narrowed out and produced a very appealing bead. The max 200Hz. yielded a slightly narrower bead then the 120Hz. If I had to use it daily for this type of joint on 16ga. I would say anywhere between 120Hz. and 200Hz. would be a good setting for this type of work. I also noticed that I could travel much faster with the increase in frequency.
Overall the Lightning performed very well on AC and DC. We will be covering the other modes, features and functions in some upcoming episodes so make sure to subscribe to the channel and click the notification bell so you never miss an episode. Until next time, Make Every Weld Better Than Your Last.
VISIT OUR WEBSITE: www.weld.com
FOLLOW US ON INSTAGRAM: / welddotcom
JOIN THE FACEBOOK GROUP - / welddotcom
Talk with Bob, Jason and Mancub!
------------------------------------------------
EQUIPMENT WE LIKE AND USE IN THE SHOP:
WEILER ABRASIVES: weilercorp.com
SELECT ARC WIRE: www.select-arc.com
PFERD ABRASIVES: www.pferdusa.com
ESAB POWER SOURCES: www.ESAB.com
EVERLAST POWER SOURCES: www.everlastgenerators.com
AHP POWER SOURCES: www.ahp.com
TAB AND SLOT WELDING TABLES: www.tabandslot.com
VIDEO SCHEDULE:
MONDAY @ 5:30 PM ET
WEDNESDAY @ 5:30 PM ET
FRIDAY @ 5:30 PM ET
Weld.com is a dedicated to helping you build your career as a welder / fabricator. Whether you’re a hobbyist, student or active in the trade; we are here to help further your craft. If you want to keep learning and interacting with us, make sure you hit that subscribe and notify (bell) button. Join us in the comment section after each video. If you have questions on projects or tests you’re doing now, head over to the Facebook group so you can share pictures with us and get feedback from the community.
FACEBOOK GROUP - / welddotcom
#welddotcom
Disclaimer: Weld.com is compensated for providing links in our descriptions. However, we only work with companies that we use ourselves and can honestly and ethically recommend to our audience.
@Welddotcom 4 жыл бұрын
Make sure you subcribe to the channel and hit that 🔔 button!
@weldingjunkie 4 жыл бұрын
Yikes! Ok that’s what I was thinking too. Nice welds brother I appreciate you sharing... J
@Ky3Sensei 4 жыл бұрын
Where's the mig review?
@ASAPJermz 4 жыл бұрын
Got y'all! 🤲🏼
@jonathangarzon2798 Жыл бұрын
Can you run flux as well?
@jeffstevens5983 4 жыл бұрын
Nice looking machine Keep up the great work guys
@randyschock7374 4 жыл бұрын
Coolest welding machine I've ever seen. Thanks for the video.
@GodslilRedneck23 4 жыл бұрын
Randy Schock thanks for watching man.
@randyschock7374 4 жыл бұрын
Thank you. Please keep the videos coming. I am a beginning welder, so there helpful. Wish I had your welder.
@GodslilRedneck23 4 жыл бұрын
Randy Schock will do man.
@J_Lag 4 жыл бұрын
Deng, nice machine, cool tutorial, thanks for the demo 👍
@GodslilRedneck23 4 жыл бұрын
Juan Lagarde thanks for watching man 👊
@handcraftedbydismore8778 4 жыл бұрын
Very good review, can't wait to see the rest. I want an all in one, this may be my ticket!
@GodslilRedneck23 4 жыл бұрын
No Fish Films it’s definitely the ticket man.
@MikeP350 4 жыл бұрын
Everlast has some nice MP machines that do mig, stick, tig, ac pulse, DC pulse, even has a 6010 stick mode
@Enonymouse_ 4 жыл бұрын
Love the new interface stuff, seems pretty straight forward. The low amperage is nice too for thin material.
@cartergimbel6866 4 жыл бұрын
I really like this welder. Looks like it can do it all.
@embersaffron5522 Жыл бұрын
Hell yeah was looking for a good review for this machine I'm probably gonna get it after this
@gorillamotors 4 жыл бұрын
I pre ordered my Lightning MTS275 about 2 months ago and I would like to see you do more videos on it. Great videos.
@ajones8008 10 ай бұрын
how has the machine held up?
@gorillamotors 10 ай бұрын
As much as I have used it it has held up pretty well. I have not tried out the TIG function yet but the stick and MIG function gets used about twice a month.@@ajones8008
@jakecarter4407 Ай бұрын
Hows it holding up?
@DonnyBwelding1 4 жыл бұрын
Slick, I am running the 211si power mts ... love my everlast ... only complaint is the case was bent pretty good because of ups but everlast was kind enough to order me another case...incredibly smoth machine. Fantastic features . Thanks for the tour of that new 275 bad boy
@GodslilRedneck23 4 жыл бұрын
Donny B thanks for watching.
@DonnyBwelding1 4 жыл бұрын
@@GodslilRedneck23 thanks for hosting . You're doing a terrific job.
@GodslilRedneck23 4 жыл бұрын
Donny B I appreciate your support. Thank you very much man.
@nesterjudkins6644 4 жыл бұрын
Mad skill Jason 🔥🔥
@GodslilRedneck23 4 жыл бұрын
Nester Judkins thanks Nester 👊🤘🔥
@everlastgenerator 4 жыл бұрын
Just a clarification: This welder has Advanced Square Wave, Soft Square Wave, and Triangular. There isn't a sine wave on this unit...though that may be something we could consider.
@LextechLighting 4 жыл бұрын
Everlast Power Equipment your welders have came along very nicely from the early days. Progress is inevitable, but you have to be trying and I definitely see effort.
@SteveBlue90 4 жыл бұрын
I have the 252 STI, any chance of an add on to be able to view all the current settings on a screen similar to that, debug port output or similar? Would be nice to glance over and check all the values rather than have to flick through.
@everlastgenerator 4 жыл бұрын
@@michaelr6392 First Quarter of 2020.
@everlastgenerator 4 жыл бұрын
@@SteveBlue90 Sorry, not in the works or capability of this machine.
@michaelr6392 4 жыл бұрын
@@everlastgenerator thank you. Does it have mig pulse as well? This is why I hesitated between the 252sti/251sti because only one machine had one and the other only had tig pulse...
@MikeP350 4 жыл бұрын
Haha, loved the editing
@FlashTechEngineering 4 жыл бұрын
I bought a 200 amp welder directly from China its the best welder ever in the amp range , I only welder I've seen or known off that does 500 ppm on AC and 500 ppm on DC current, I have the everlast 255 ext welder for slightly heavier aluminium, but my go to welder is the Chinese welder, it cost me about $570 Australian dollars freighted to my business and have used it for the last 5 years not one issue, my everlast cost $3150 The Chinese are ahead in the market place in technology and engineering we don't always get the models released R and D , my welder was hand built and assembled for me directly from the company and that is standard for new customers , some of the features on my welder are slowly being released on the market now, 5 years latter 👍😀
@FlashTechEngineering 4 жыл бұрын
Sorry typo should have bee pulses per second
@jacksonlee5189 4 жыл бұрын
Please show more videos about this welder.
@mr.tarkovish2587 3 жыл бұрын
Man I can’t wait for this summer to work my ass off and buy this bad boy 🥵
@ASAPJermz 4 жыл бұрын
AC TIG, bad ass! But, I'm just not a TIG guy, even though I've seen the most beautiful welds being produced by this process. It's just something about SMAW & even MIG from time to time that always reminds me of why I started welding..
@videodistro 4 жыл бұрын
Square waves go from peak to leak much faster than triangle, almost instantaneous versus a slow crossing of the null with triangle wave forms. Triangle is more "gentle" in the change.
@busancun 4 жыл бұрын
Nice review, for the excellent AC TIG I'll definitely go for this rather than Fronius 2200c. By the way, the water cooler is included in the package?
@bradymcphail9690 4 жыл бұрын
Excellent sir, I bought the MTS 235 several years ago and have yet to use it. I'm a renter, and my landlord wont allow me to install 230v into the garage. I didnt think of that when I purchased the welder and the plasma cutter. Dohhh! Now with the electrocution I'm not sure if I will be able to go back to welding, I'm pretty torn up...
@bwjbrown 4 жыл бұрын
Do you have a dryer receptacle close to your garage? You can get a receptacle converter and extension cord that will give you nearly your machine's full capability without changing the wiring. The dryer circuit (and breaker) are likely at 220v 30amp - unless you're trying to weld a Navy ship or bulldozer (which you could do on stick anyway), you're not going to pull more than 30 amps anyway.
@replyhere590 Жыл бұрын
@@bwjbrown Range receptacle in kitchen is likely 50A
@Luke_KJ 3 жыл бұрын
Assuming I had the money and needed a new welder, I would just spend the couple hundred extra and buy the multimatic 255. My current everlast works good for what I need it for though. And I don't have $2500 laying around either haha. Great review though, keep up the good content.
@jessehill6661 3 жыл бұрын
The Multimatic 255 is not a "couple hundred extra", it's at least a grand extra. And even though it can do push/pull aluminum, it CANNOT AC TIG aluminum. Not really a comparable machine.
@hottrod757 4 жыл бұрын
Dude I want that weld cap, semper fi
@mrjodoe 4 жыл бұрын
i knew you like the 33. btw nice Gloves, I use the same - i recommend testing "spongetex grip extreme"
@GodslilRedneck23 4 жыл бұрын
qwertz33 I’ll give them a try.
@HH-cw1tl 3 жыл бұрын
After having the MTS 275 over a year would you say it's a solid machine?
@prestonprince3406 4 жыл бұрын
SO there THEY were... El Padre, Pedro, and Pato, all brave and heroic llamas trekking through the candy cane forest when they came across a magical bale of hay. P.S. opinion on welding school. Thinking about Tulsa, OK
@GodslilRedneck23 4 жыл бұрын
Preston Prince DM me on instagram. @redbeardweldz
@rjbaima Жыл бұрын
I BOUGHT THE M.T.S. 225....DOES THE JOB FOR STAINLESS & ALUM. SETTING ARE EASY TO WORK WITH ...HAVE'NT TRIED THE MIG SPRAY YET..OR THE STICK...
@Anday0 4 жыл бұрын
I'm about to purchase a welder for my shop and I'm unsure which welder to buy. The lightning 275 MTS and the Power MTS 252 Sti are the same price. Should I just buy the 275 or does the 252 offer something else?
@CrazySparkie63 4 жыл бұрын
Could you explain what difference the different waveforms have on AC Tig welding!
@DCweldingAndArt 3 жыл бұрын
Advanced square is all around best, controlled arc n good heat input. Soft square and triangle wave are better for thinner alum because EN and EP are are switching faster so less heat input, sine wave is just like the old transformers (syncrowave, precision tig) which is sort of like soft square. I mainly use advanced square on +1/8" and triangle on 1/16" or less
@Kevin.L_ 4 жыл бұрын
Jason, about half way through the 1HZ outside run it looked like you switched from adding filler during pulse on to pulse off. Was that intentional or just an optical illusion?
@GodslilRedneck23 4 жыл бұрын
Kevin Lee probably an illusion. I ran pulse the whole time.
@gorillamotors 4 жыл бұрын
Just pre-ordered mine. The pre-order price is $2500. They start shipping at the end of December. After which they will cost $3500.
@benmiller5015 4 жыл бұрын
Been waiting for videos to start coming out for that beautiful beautiful baby
@GodslilRedneck23 4 жыл бұрын
Ben Miller glad we could show you the capabilities.
@benmiller5015 4 жыл бұрын
@@GodslilRedneck23 I'm sure you've only scratched the surface of what it can do. I saw someone else do I bit of mig with it in another video. But I'm looking forward to seeing you get into that machine n push it. If I remember from the lil amount of information that was out about it a month ago it's a 250 amp machine with the 60% duty cycle like the 252 sti. Does it have sinergic on it too?
@GodslilRedneck23 4 жыл бұрын
Ben Miller thanks for the vote of confidence. We will review the remaining functions very soon. I can’t give away too many details yet. Stay tuned.
@FishFind3000 4 жыл бұрын
I’ve been looking to upgrade my everlast 200sti stick machine into multi process and this might be the ticket, if the price is right. There machines are great for hobby use where industrial reliability isn’t required.
@conradanderson404 2 жыл бұрын
Eoupd you say it's not reliable enough for industrial use?
@jonathangarzon2798 Жыл бұрын
It has an industrial duty cycle, what about it isn't reliable?
@FishFind3000 Жыл бұрын
@@jonathangarzon2798 by industrial duty cycle I mean 100% duty cycle. My everlast only has like 20-30% duty cycle at max amps.
@jonathangarzon2798 Жыл бұрын
@@FishFind3000 industrial duty cycle standard is 60% but okay yeah that's not that good.
@WeekendPursuitOutdoors Жыл бұрын
So are you still using this welder and if so how has it held up?
@davidfrank2824 3 жыл бұрын
I know they're one of your sponsors but I do have a question that I would like your honest answer on. Is this machine too much for a beginner? I'm not talking about the price I actually think the price is pretty damn good for everything that comes with it. I just don't know if this machine has too many settings for someone starting out. Most of the time I plan on using this to repair body panels on car bikes trucks hell even an airplane if you can get it in my yard lol. It's very close friend of mine owns a large welding company across the whole state that I'm in. There is time that he gets things that is too complicated of a weld for his guys. All they do is stick weld. And they're not getting judged on how well the weld looks. He has a lot of different things that people contact him for and it's mostly stainless steel and then aluminum. I do know how to stick weld when you have a close friend that owns a large welding company sooner or later they will ask you to go with them a give them a hand. Matter of fact all they use is gas powered machines. Most of the time when they break he does not have time to fix them and most of them come to my house so I can work on getting them back up and running. With doing so I have learned stick welding. I don't do a lot of MIG welding right now. He gave me a brand new Miller 140 a few years back for getting three of his machines up and running in one day. The only thing is that it's set up for flux core and as you know all I would need to do is hook a bottle up and change my wire. Sorry forgiving you so much information but I figured it would help you to answer my original question if you knew a little bit of my background in welding. I do enjoy your videos and yours was some of the first ones that I had watched to learn more about a tig welding. Look forward to watching some more of your videos.
@gorillaxrich 4 жыл бұрын
What kind of increments does it have for low end pulse??? Like can you get 1.4, 1.5, 1.6 pps etc.???
@DD-rb6hi 4 жыл бұрын
Just found this channel Awesome. What are the chances that you can compare this with the Miller Multimatic 220. I'am a Noob with welding. about to buy my first machine was looking at that Miller and the Everlast 221 STI. I had a phone conversation with a Everlast rep and he suggested that model. Whats your view???
@SheikYerbuty 4 жыл бұрын
Did you ever do a GMAW review , and why not?
@Aint1S 4 жыл бұрын
I would have loved to know what your settings were for that can weld! Machine and the Argon please, sir?
@GodslilRedneck23 4 жыл бұрын
Aint1S 1/16” tungsten 30° grind angle, 1/16” E4043 filler, gas lens with 20CFH, 20amps no pulse 200Hz frequency. You need to clean the cans really good, we used 120 grit sandpaper and then scotch brite. Then wipe it down with acetone. Poke a hole in the very bottom of the cans so the air can escape. If you don’t the air will heat up and blow out your weld towards the end. Good luck man. Oh and you’ll also need a pallet of patience 😂 👊
@Aint1S 4 жыл бұрын
@@GodslilRedneck23 I've never poked the hole nor used 200Hz for it after the most foil failure on my first try a few years ago! Holy smokes, those cans can stink my whole shop out! Great machine you have there and amazing advice! 255 EXT here... I welded the to razor blades and stepped down to two 60° exacto blades with some of my electric guitar string. That was high science using that wire, but I kept that one for proof. It's the smallest bead ever I've ever put down dabbing. Looks like a sharp ♥️.
@cramersclassics 3 жыл бұрын
@@GodslilRedneck23 This would be very handy if your beer can sprung a leak :-) Your welding videos are the best!
@lorenwegele7517 4 жыл бұрын
You're good Jason! Should we up the ante when you weld full Coors cans together? They used to be the thinnest ones out there..... 😁
@GodslilRedneck23 4 жыл бұрын
Loren Wegele that’s about all Coors is good for 😂 j/k man. Thanks for watching.
@lorenwegele7517 4 жыл бұрын
@@GodslilRedneck23 Lol! THAT'S no kidding! I prefer bourbon barrel aged Imperial Stouts or Belgian dubbels, tripels and quads. 😊 By the way, what part of the country are you and Bob teaching in? I gather it's no longer at Cowley County College in Ark City, Kansas.
@timetogetcanceled 3 жыл бұрын
how thick of aluminum will the tig side weld?
@davidfrank2824 4 жыл бұрын
This machine is so new it's not even up on the manufacturer's website. do you have any idea on when this will be available to the public?
@ryandayon2250 29 күн бұрын
Is the machine still working good? I’m about to buy one.
@Matt-re9oh 4 жыл бұрын
Can you make a video of some 6012 welding
@stanleykinzinger 3 жыл бұрын
lookin into this machine right now lol
@aaronmonds7336 4 жыл бұрын
Can u link were u got that welder
@automaticprojects 4 жыл бұрын
How do you think this machine compares to the ESAB Rebel 205 and Millermatic 220?
@Farmer1277 3 жыл бұрын
More power. The Everlast Lightning MTS 225 is more comparable to those.
@clutchshot247 6 ай бұрын
But what about reliability compared to others .. i noticed every reliability question wasnt answered on this thread, hmmm
@danielmartinez-cj5di 4 жыл бұрын
I want this welder.
@GucciTheGlacier 3 жыл бұрын
How big of a spool of wire can it fit?
@user-xq9yn3hy3u 4 жыл бұрын
What's better Everlast vs Esab???
@natecox9955 4 жыл бұрын
Can this be switched to 3 phase?
@josephlassiter1412 4 жыл бұрын
Can you walk the cup on aluminum?
@772777777777777 3 жыл бұрын
I have a mys252...and im newbie to tig welding... need some tips a advice... have the below questions Im trying to practise weld with no filler... on some clean 1/4 steel plate.... welder set dc tig.. 125 amps post flow is 8 sec... when end my weld and the arc stops my tungston melts... and i didnt dip in the weld pool.. i think i dont have my welder set up correctly... also when im welding the display say only 20 amps and im not get a good weld pool i have nice arc... but not sure what going wrong.. Can anyone help or make 101 tig video using mts 252 setup video
@louiegrabske5054 5 ай бұрын
Looking at one of these lightning 275's for our shop. Trying to decide between this or the Millermatic 220 ac/dc. Dont do much aluminum tig but would like the option and ability to learn more. for the money these machines look really hard to beat! Anyone suggest this over the miller and why? I realize that theyre different amperage machines and the Everlast is considerably less and can get the water cooler/cart package for over $1000 less. Thanks!
@arthurpridanovs2336 3 жыл бұрын
Can I ran this machine of generator? considering it have enough power?
@africantwin173 4 жыл бұрын
Hmm, no retailers in the Netherlands.
@byron7165 4 жыл бұрын
Now that you've done the review, I will graciously accept shipment of your donation to my welder needs. Thank you so much! :-)
@Welddotcom 4 жыл бұрын
Still have to do MIG, Stick and Flux Core. After I'm sure we can send it your way 😜
@byron7165 4 жыл бұрын
@@Welddotcom Yay! I'll chip in for shipping ;-)
@Welddotcom 4 жыл бұрын
@@byron7165 just hit that 🔔 button. Camera guys got you covered on shipping.
@benmiller5015 4 жыл бұрын
Well if you're gonna give one to anyone who asks can I have one too? Or you can give me your old boring clunky 252 sti lol
@Welddotcom 4 жыл бұрын
@@benmiller5015 🤔🤔 only those who have notifications enabled get free machines 😂
@Ramdodge582 4 жыл бұрын
is it wrong this welder gives me a chuby?
@tylerjenkins91 4 жыл бұрын
Is your beard a fire hazard?! Rofl keep it up! Good stuff
@Welddotcom 4 жыл бұрын
There's a reason for the leather beard guard 😂
@GodslilRedneck23 4 жыл бұрын
Tyler Jenkins my beard was born in fire 😂
@beachboardfan9544 4 жыл бұрын
In my experience pulse has always produced a better weld. Is there ever a time when its not appropriate to use?
@GodslilRedneck23 4 жыл бұрын
Beach&BoardFan it’s all user preference. Usually on thick stuff I won’t use pulse.
@beachboardfan9544 4 жыл бұрын
Interesting, whats the reason, it just slows the weld because the heat is on and off?
@GodslilRedneck23 4 жыл бұрын
Beach&BoardFan correct, it allows for quick moments of cooling in the puddle.
@beachboardfan9544 4 жыл бұрын
You guys ever do any copper or aluminum bronze mig welding? I just started doing it and am currently struggling with undercut. The welder is an old miller deltaweld 451. 40 cfh of helium 29.5V The wire speed is just a numbered dial thats set at 2 1/4 (it doesnt say inch per min or anything) 1/16 solid copper wire While welding horizontal I get terrible under cut. I'll tilt the wire up about 5-10 degrees but it still undercuts about 1/16th of an inch. Flat is fine and over head is fine, but horizontal always undercuts. I've only ever tig welded copper before, so this is uncharted territory for me.
@GrandpaBill 4 жыл бұрын
Must be really new as it's not listed on their website.
@Welddotcom 4 жыл бұрын
It's not been released yet. We are doing some product testing for them and giving feedback.
@GodslilRedneck23 4 жыл бұрын
Grandpa Bill shh it’s a secret 👍
@floridabeardedwoodworker 4 жыл бұрын
so was this a review or instructional?
@marcotte6608 4 жыл бұрын
What’re those gloves you’re wearing lol looks like maxi flex.. Edit: they are maxiflex are those thick ones or what?? I’ve never had a pair of those I could weld in besides bridging and deck lol
@GodslilRedneck23 4 жыл бұрын
Joshua Marcotte I used these because of the low amperage and small filler size. I needed more dexterity. I wouldn’t recommend them for welding with for most things.
@LextechLighting 4 жыл бұрын
Say, everlast wouldn’t happen to be sending these out would they? Lol kevin caron yesterday, now you guys. Worth noting his vid has 1.2k views in over 24 hrs and yours hasn’t been out a full day and has 10k. Maybe they should send one to me next time if they want that amount of views. I can pull that off.
@byron7165 4 жыл бұрын
At 2 amps you should be able to weld straight-razor blades. An amp and a half for tinfoil ;-)
@bigboygames8800 4 жыл бұрын
What happened to bob
@micmike 4 жыл бұрын
why doesn't anyone mention the cost of this machine?
@alexam694 4 жыл бұрын
When's Bob coming back?
@jfuqua72 4 жыл бұрын
Love Bob, but this guy is way better.
@HamRadio200 4 жыл бұрын
is this machine even available?
@Welddotcom 4 жыл бұрын
I believe they are planning on releasing it end of 2019 - Early 2020. We have it to do some product testing and we thought we'd give everyone a little sneak peek.
@weldingjunkie 4 жыл бұрын
How much is this machine Jason?
@Welddotcom 4 жыл бұрын
It's not out yet. But I believe Everlast is saying it's going to be in the upper 3 grand range.
@everlastgenerator 4 жыл бұрын
@@Welddotcom That's our intention.
@Rawchester45 4 жыл бұрын
That welder out already?
@Welddotcom 4 жыл бұрын
I believe they are planning on releasing it end of 2019 - Early 2020. We have it to do some product testing and we thought we'd give everyone a little sneak peek.
@everlastgenerator 4 жыл бұрын
We have our PowerMTS 252STi, which is similar but with different interface and minus a few features.
@Rawchester45 4 жыл бұрын
Thk really looking forward to this one not in a hurry to get one I’ll wait till end of year.👍
@rustydodge6167 4 жыл бұрын
Where are BOB and MAN CUB?
@btrswt35 4 жыл бұрын
I think I need some translation. "Welds are decent", is that good or is that acceptable?
@frankbibby6847 4 жыл бұрын
I think he was trying to be humble, the welds look primo
@GodslilRedneck23 4 жыл бұрын
David Mm they can always be better. It’s been a while since I’ve done TIG work. I have learned in my years never to brag on my work. There’s always someone better out there especially in the comments section 😂
@pizzaWelder 4 жыл бұрын
Where do I pick up that hat???
@ouroboros5378 4 жыл бұрын
Mister tig? Bob?
@525medic 4 жыл бұрын
I never post “that’s not good!” Comments, seriously...but what the hell happened with that last 200h aluminum filler work?!? Not to say I haven’t done worse 🤣
@GodslilRedneck23 4 жыл бұрын
525medic it got a little gummy on me. I was trying to run too fast.
@525medic 4 жыл бұрын
Jason Becker it happens lol. Could be the camera angle, but looked like you could’ve used a little less torch angle maybe. Love the new style of the videos btw
@MrinsaneMr 4 жыл бұрын
This company doesn't care about the home or small business market at all. 😒
@mohammedtroy4296 4 жыл бұрын
u.s. marine
@GodslilRedneck23 4 жыл бұрын
mohammed troy what’s up Mohammad 🤘🔥
@mohammedtroy4296 4 жыл бұрын
@@GodslilRedneck23 you are a specialist
@GodslilRedneck23 4 жыл бұрын
mohammed troy thanks man 🤘🔥
@mohammedtroy4296 4 жыл бұрын
@@GodslilRedneck23 we are the smart welders we are not the dumb ones who like to weld is muddy waters who refuse to ask the 1% to drain the ditch or build a platform to weld a joint so billions can be made
Everlast Welders
Рет қаралды 54 М.
Repair Geek
Рет қаралды 32 М.
Pacific Arc Tig Welding
Рет қаралды 98 М.
Everlast Welders
Рет қаралды 456 М.