Nissan P0507 Idle Control System - Idle Relearn Procedure

Рет қаралды 656,158

8 жыл бұрын

This Nissan Murano had a code P0507 after performing other repairs and cleaning out the throttle body. This particular code basically means that the RPM are higher then expected probably from an intake/vacuum leak or something like that.But in this case I was almost sure that it was caused because we cleaned the throttle body. so this is how you do the relearn of the idle control system.
if you want to help out the channel, just use my Amazon link when sopping at amazon.
amzn.to/2KEtHCp
*RE-LEARN PROCEDURE STEPS*
Idle Air, Volume Learn.
1. Make sure the accelerator pedal is fully released.
2. Turn ignition ON, do not start engine, then wait 3 seconds turn the ignition back off and wait 10 sec.. redo this procedure 3 times
3. Next, Fully depress and release the accelerator pedal 5x within 5 seconds
4. Wait 5 seconds, then fully depress and hold accelerator pedal. After Approximately 10 seconds, the Malfunction indicator light will switch from steady to blinking. Approximately 9 seconds later, the light changes from blinking to steady once again.
5. Fully release accelerator pedal and start the car within 3 seconds.
6. Allow to idle. Wait 20 seconds.
Hope it help some one out there. Don't forget to SUB!!!
If you would like to leave a donation here is a link ...
www.paypal.com/cgi-bin/webscr...
Follow me on INSTAGRAM
/ falcons_hobbies
Twitter.
/ shospeed
Facebooks Hobbies
/ falconshobbies
My Gaming Channel.
/ @falconsgaming
The information presented in this program is based on a specific diagnostic case and might not directly apply to the vehicle you are repairing. We do not represent or warrant that the information presented is complete or error free. Please take all safety precautions. We disclaim any and all liability for losses, injuries or damages in connection with your repair."

Пікірлер: 400

@FalconsGarage 6 жыл бұрын

if you want to help out the channel, just use my Amazone link when sopping at amazon. amzn.to/2KEtHCp

@roopnarinedeonarine4085 4 ай бұрын

Thank you guys,very helpful..

@golfish8589 4 ай бұрын

The srvice engine soon light does not stop flashing at the end of the procedure on our suv

@rapidtransit8373 3 жыл бұрын

You guys save people money that don't have it. Taking a car to the dealer is very expensive. They charge 100 dollars just to put it on a scanner. Thanks a lot for helping people .

@FalconsGarage 3 жыл бұрын

glad to help people

@CharleneDixon-kw4mn 7 ай бұрын

Thank you very much, your video really helped me. I'm a single mother and I follow your instructions of what you said and it works. Thank you❤

@FalconsGarage 7 ай бұрын

Glad I could help!

@sheeshalready 2 жыл бұрын

I tried this method on an 07 Altima several times, did not work. I finally hooked up my ThinkDiag in hopes that it would have the ability to do the relearn, and it did. Fixed it perfectly. We appreciate videos like this, thank you.

@FalconsGarage 2 жыл бұрын

yes doing it with a scanner is always much faster and secure to do

@cpd969 Жыл бұрын

Which model of ThinkDiag tool please?

@danielstroup6581 7 жыл бұрын

If this isn't working for you and you still have a high idle and check engine light, do all 3 procedures with the engine fully cold! It worked on my 06 Nissan Pathfinder. I cleaned my TB and my truck started idling around 1K and check engine light. Tried this procedure about 20 times with engine and transmission fully warm and it did not work. Next day, I thought I would try it with engine fully cold with nothing to lose and BAM, 625 RPM after a few minutes of warming up. Good luck!

@johnargue2977 7 жыл бұрын

procedure starts at 2:04

@MrBigjoe2400 Жыл бұрын

Pin this comment

@rbarron007 11 ай бұрын

Thank you

@Guts33 11 ай бұрын

This fixed my hard start issues on my Sentra 2005. Thank you!

@FalconsGarage 11 ай бұрын

Awesome! Glad I could help!

@frank8263 7 жыл бұрын

Hi Falcon. I Can not Thank You Enough!!!!!!! I have 2007 nissan sentra 2.0 engine car ran terrible i cleaned the throttle body and the hose to it was cracked i replaced it. After cleaning throttle body ran better but the idle was high and surging while driving . Well thanks to You i Followed your Procedure it worked on the First try i am totally Amazed my car runs PERFECTLY !!!!!! . Again Thank You!!!!....... Frank

@FalconsGarage 7 жыл бұрын

I'M GLAD I WAS ABLE TO HELP!!

@si2thet 5 жыл бұрын

Went through the instructions, didn't get the flashing indication, but it cleared none the less. Thx for the vid!

@alfonsocorona1008 Жыл бұрын

Same here for my 2006 Sentra SE. went through the procedure and was going to redo it so I started the car after noticing if din’t flash within 20 seconds, but when I started the vehicle the engine light was off and idle was back to normal

@dfields9511 3 жыл бұрын

This is great It’s the Hitachi relearn procedure Apparently hitachi makes this component for Nissan I think.

@bradm6205 6 жыл бұрын

Thanks, it worked great!. I did clean my throttle body and my RPM increased. I thought that was normal till I got that P code. You video helped me work that out.

@bradm6205 6 жыл бұрын

2005 Nissan Frontier

@FalconsGarage 6 жыл бұрын

Im glad I could help!

@tonycervantes4816 2 жыл бұрын

Como lo limpiaste el throttle body

@larrysparks2599 4 жыл бұрын

Worked like a charm thanks man..

@rafrubio1955 Жыл бұрын

Perfect video for my issue 💯

@crenshawstew4475 5 жыл бұрын

YOU DA MANNN! New sub forsure🙌🏾🙌🏾

@jeremyolsen2891 2 жыл бұрын

I totally botched the process. BUT IT STILL WORKED! 2002 Nissan Sentra. Thank you so much.

@nestorcaamano307 4 жыл бұрын

Thank you for your help and support it work for me .

@FalconsGarage 4 жыл бұрын

Glad to hear that

@Kencan72 3 жыл бұрын

Worked great on my Nissan350Z! Thanks a lot bro! Worked on the first try too! After I had my CamSensor Bank replaced, my car was idling around 1500 rpm! Now I’m down to a solid 500rpm!

@Kencan72 3 жыл бұрын

And just a follow up, anyone doing this: after it works and your car is idling in the right zone, leave your car running for about 10 minutes, at least. Turn on your AC and your rpms will go up again. Let it run for about 10 minutes again.

@FalconsGarage 3 жыл бұрын

Glad it helped

@JuanRodriguez-uh4hr 3 жыл бұрын

@@Kencan72 hey man I cleaned my throttle body recently on 350Z

@JuanRodriguez-uh4hr 3 жыл бұрын

@@Kencan72 got this code so this will work

@jonathangarzon2798 Жыл бұрын

@@FalconsGarage does this work on a 2015 Nissan frontier

@nasnismo52 7 жыл бұрын

Works for my nissan latio/tiida/versa 2006. Thank u.

@FalconsGarage 7 жыл бұрын

GREAT!!! Thanks for the Info..... Glad I could be of some Help!!

@baubaby 8 жыл бұрын

Worked on my '07 Pathfinder

@FalconsGaming 8 жыл бұрын

glad it did!!!

@isaackhan4325 6 жыл бұрын

Great video. Thanks

@joserubio2622 4 жыл бұрын

Thanks bro it really worked

@gedi73 5 жыл бұрын

Thanks brother I got it

@JLE1177 6 жыл бұрын

I did it with you perfect the check engine blinked then went solid and I cranked it and the thing I notice is it idles at 1 but if I tap the pedal it kinda jumps a little bit prob half rpm and then settles. Feels unnatural. Did I do it wrong maybe?

@isaiahsantiago8550 Жыл бұрын

Worked!! Thank you so much !!

@juancarloscontreras958 7 жыл бұрын

Thanks I'm gonna try it tomorrow!!!!!!!

@FalconsGarage 7 жыл бұрын

Good luck!

@hotchef1984 3 жыл бұрын

Sir you are my hero. Works on '07 nissan versa.

@FalconsGarage 3 жыл бұрын

LOL, Thanks for watching

@jamesholzer181 4 жыл бұрын

will give it a try

@JLE1177 6 жыл бұрын

Wait lol I did again and this time the rev settled at 500 and didn’t seem to be jumping anymore....Bro! You are the shizzznit my friend lol thanks so much! Liked subed 👍🏼

@FalconsGarage 6 жыл бұрын

Glad I was able to help!

@JLE1177 6 жыл бұрын

Falcon's Garage how do you know when the tb need to be replaced though?

@mrjadogproductions8076 4 жыл бұрын

This one worked for me

@wildcousa 6 жыл бұрын

You the man seabass

@anthonysalinas6195 Жыл бұрын

I'm definitely going to have to try this out. I just picked up an altima with that code on it

@alan4sure Жыл бұрын

And???

@anthonysalinas6195 Жыл бұрын

@@alan4sure and what?

@alan4sure Жыл бұрын

@@anthonysalinas6195 did you try it out? Did it work?

@ryanlombard3736 3 жыл бұрын

07 maxima: I wasn't doing it right at 1st but finally got it. When it started the light went off but came back on. RPM definitely went down & seems stable but what do I do now??

@mikemillions4748 3 жыл бұрын

Thank xx bro that real help

@elvishgonzalez513 3 жыл бұрын

You are the best

@Lazydawg5000 4 жыл бұрын

Thank you

@ML_1515 4 жыл бұрын

Thanks for the vid! Will this work on a 2012 Nissan Murano?

@henlerflores8658 10 ай бұрын

Thanks 😂it work,gracias muchas

@juliansdiamonds Жыл бұрын

Thank you so so much !!!

@FalconsGarage Жыл бұрын

Glad it helped!

@juliostulios8125 2 жыл бұрын

Awesome thank you.

@FalconsGarage 2 жыл бұрын

No worries!

@kaleidoscope8743 6 жыл бұрын

I have 2006 Nissan Altima and just bought it used (it is July 2018). I bought it off my nephew's used car lot - they just got it as a trade in. My symptoms are: I usually get steady idle at 1000 rpms in Park or Neutral. Occasionally, I get steady idle at 1500rpms. But abt every 8th engine startup it'll immediately dip once to abt 600rpm and steadily climbs to 2000rpms where it will start a cycle of dropping & surging between 1000 and 2000rpms. It stops the surging & high idle as soon as i put it into gear (drive or reverse). It will not do it on next few cranks. It'll take about 6 or 8 cranks to hit it again. My MIL is P0507. The dealership changed an engine mount the day before it started happening. At first my nephew thought the mechanic might've left something unhooked or knocked something loose pulling off the cover to get to the engine. Is this a potential? What all should i check? Do you have a video that covers every point of failure in this system? Thanks

@FalconsGarage 6 жыл бұрын

have you checked for vacuum leaks or your spark plugs? i dont think there is anything around the motor mounts that could be disconnected to replace them that would cause this issue..specially sense it docent do it all the time, Have you checked if the throttle body is dirty too?

@kaleidoscope8743 6 жыл бұрын

Falcon's Garage i checked an electrical connector that plugs in at the air filter box. I opened the air filter box to be sure that the filter was clean. It's not new, but it's not bad. I have not looked at the throttle body or any of the vacuum hoses. Do you have a video that explains how to check vacuum hoses, Air valve, IAC, throttle body.... and changing spark plugs on nissan. (Ive changed plugs on 1973 Honda Accord cvcc. But ive never done a tune up on car with fuel injectors. ) I partly disabled am able to do some repairs myself. I was an aircraft electronics technician in USAF. i have an electronic/electrical'mechanical education. I have a little experience on cars (belts hoses, alternator, battery, solenoids, wiper motor, headlight switch & wiring, choke, ... nothing major. Anything using hand tools I can often do as long as i have instructions (how to with dos and donts). Any help is appreciated.

@FalconsGarage 6 жыл бұрын

kzfaq.info/get/bejne/hZeqd9GDsLqRZX0.html

@kaleidoscope8743 6 жыл бұрын

Thank you. I will watch and like. The day after you replied, the CEL went out on its own ... about 3 driving cycles after I had reseating the (MAP ?) connector at the air filter box. Is this a coincidence? Also I have not had the gas cap open to refuel, in case the gas cap was the problem (I tried to get the cap as tight as possible last time I refueled). For now, whenever I start the car, I immediately put it into gear to avoid idling in park. And whenever I park the car, I immediately shut off the engine to avoid idling in park. I am doing this to avoid any re-encounter with idle surging to keep the CEL from coming back on. I plan to change the gas cap the next time I refuel. I had already bought it from the Nissan dealer (before the 507 CEL incident) because I was dinged on the state inspection for not having the factory specified gas cap. They didnt ding me on the CEL but it might be a problem for the emissions check. I am trying to solve it before I have to take it in for emissions check.

@kaleidoscope8743 6 жыл бұрын

do you have anything on changing a serpentine belt from the engine bay on 2006 Nissan Altima.

@guillermocarrillo3253 Жыл бұрын

Good video

@fernandourtusuastegui5726 7 жыл бұрын

does it work on a push start too?

@countryboy140 4 жыл бұрын

Thanks for the video it help me

@jcalzada74 5 жыл бұрын

This will work on a nissan frontier 2003 2.4 4 cylinders

@jomoreno3067 2 ай бұрын

I have this code on 2015 Nissan Murano. Push start !

@allenrachal 7 жыл бұрын

you saved my car. light went off after doing this procedure 5 times in a row.

@FalconsGarage 7 жыл бұрын

sometimes it takes a couple of times to get just right! I'm Glad I could help!

@keondozier101 7 жыл бұрын

damn bro it actually worked

@FalconsGarage 7 жыл бұрын

Glad I could help!!

@rebeccaquam5133 7 жыл бұрын

would this work on a Nissan versa 2011

@cardion411 4 жыл бұрын

I freaking love KZfaq.

@jpast2069 10 ай бұрын

Perfect

@Mixwell1983 4 жыл бұрын

Mine poppee up on my gfs car because I took the sensor plug off to check her ail filter and forgot to plug it in when she started her car.. Gotta try this out.

@h22sparkle 6 жыл бұрын

I just did it and it worked it was that throttle body assembly when it takes a shit get another one swap it out with an brand new one not a used one

@FalconsGarage 6 жыл бұрын

agreed, Glad I was able to help!

@gregsanders2145 4 жыл бұрын

Thank's

@damianayala2270 7 жыл бұрын

I have a 2003 350z will it work the same?

@theseattlegreen1871 Жыл бұрын

Could you upload same video only with push start instead of key?

@TylerZ 7 жыл бұрын

Thank you! Cleaned the throttle body on my Sentra and the idle was going nuts.. Thought I had screwed it up.

@FalconsGarage 7 жыл бұрын

Glad I could help!

@TylerZ 7 жыл бұрын

Car got backed into two days later, may be totaled. Well, at least it ran...

@Shane23Armada 2 жыл бұрын

Same here smh but didn't work for my 2013 armada

@chosenjuan3335 8 жыл бұрын

I have a 2012 max and my rpms are 1200 push start how do I do this process

@ablake2418 10 ай бұрын

Just sorted my elgrand that was idling at 1200rpm thanks

@FalconsGarage 10 ай бұрын

Awesome!

@user-fr3sx5uf6z 8 жыл бұрын

thanks

@FalconsGarage 8 жыл бұрын

glad I could help

@spencerorme435 3 ай бұрын

How do you do this on a Nissan that has keyless start

@roybeltran1 4 жыл бұрын

Great explanation. It worked on my Nissan Sentra 1.8S. Thank you much.

@JasonSmith-qx3zh 4 жыл бұрын

That was my question let's getrdone now thanks !!!!

@truetransformeranimations8573 2 жыл бұрын

How do you do this if you have a key fob? 2015 Nissan altima

@AEFarnam 5 жыл бұрын

Dude omg....tried this last night like 40 times with another dudes video, could not fucking get it... Literally 1 try with your video, SUCCESS!!! Thank you my brother, you really really helped me out today!!!

@AEFarnam 5 жыл бұрын

Dang, I literally saw the rpms drop to normal level, within spec. So I test drove it and it SES might came on and now its back to high rpm, not as bad as before, but 1100 rpm in park at idle. What do I do my man??

@FalconsGarage 5 жыл бұрын

Have you checked vacuum leaks or if the throttle body is dirty? Also all Nissan are known for the intake hose to crack with time. The one between the MAF and Throttle body.

@raulperero 7 жыл бұрын

great

@Koosh1983 4 жыл бұрын

Mine won't take. Stereo off, AC off, no other load. Anything else I may be missing?

@yishaithegift9953 3 жыл бұрын

How is done with push button start?

@julioalvarez2757 5 жыл бұрын

Thank you for the video Falcon's Garage. I have a 2002 Nissan Altima 3.5 SE. It's pulling this code P0507. The shop where I took it, is telling me that I need to replace the Idle Air Control Valve. But I previously replaced the throttle body with a new one and I don't think it was relearned. I wonder if that's what throwing the code. Any suggestions. Thanks!

@solidjose54 4 жыл бұрын

Julio Alvarez hey had the same issues as you now atm. Can you tell if what you did to fix your situation

@RicardoMartinez-kr5qk 4 жыл бұрын

This one worked for me, 04 altima, after trying multiple versions found on KZfaq and the forums, including those claiming to be "from the factory". This one was found by my beautiful, voluptuous, curvy, sexy wife, so credit goes to her for finding this video.

@RicardoMartinez-ug4vv 4 жыл бұрын

😂😂😂

@WilliamLopezOficial 4 жыл бұрын

Excelente.

@stevemcc4447 3 жыл бұрын

Thanks! my 2015 Rogue just quit yesterday. Turned out Pos cable was loose. When it came back to life after a jump, idle became radical and car was jerking and struggling, like fuel pump. I am starting with the IAC. If I clean throttle body, can I try your procedure next? Also, do you recommend a code app for iPhone or some other not-too-expensive checker? thanks again!

@FalconsGarage 3 жыл бұрын

i would buy ab obd

@jamestolliver6180 3 жыл бұрын

Will it work for 05 Altima

@eddyluaku8151 Жыл бұрын

Ma Nissan Murano 3.5 V6 2006 AT essence ne démarre plus. C'était dans un embouteillage, le moteur avait coupé et j'ai essayé de démarrer mais en vain. Que dois-je faire ?

@andyleyva1828 2 жыл бұрын

How can I do this with a push to start?

@tonycervantes4816 2 жыл бұрын

I have that code. You think of problem. Is of iAC ??

@joselopez1456 3 жыл бұрын

Will work with a 2010 maxima

@michaelalvarado8705 7 жыл бұрын

hey man I just saw your video and great explanation but I had a question I have a 2007 Nissan Frontier 4.0 and I ended up cleaning the throttle body and the same code popped up. I do feel like the truck is pushing itself a little bit did your car do the same? and do you know how long it takes for the chemicals to go through the engine because the shop told me that it takes about 50 to 75 miles for it to get it through the system

@FalconsGarage 7 жыл бұрын

what chemical? did you not take off the throttle body to clean it? or did you just used some chemical on the intake?

@michaelalvarado8705 7 жыл бұрын

I used throttle body cleaner. i actually had to run the test twice and now its running better than ever! thank you! very good explanation. i just get scared when things are not working on my truck.

@kahlenoa000 4 жыл бұрын

Had code P0171 (system too lean bank 1) so I decided to clean the MAF sensor and throttle bottle with the appropriate cleaner (I’ve don’t it before). Resulted in added code P0302 (cylinder 2 misfire) and it revs up and down constantly. Filled it with Techron complete fuel system cleaner and filled the tank. The previous codes then disappeared and I now have the constant reving plus code P0507 idle control system RPM higher than expected. Should I replace it?

@FalconsGarage 4 жыл бұрын

have you done a smoke test .. to see if there is an intake leak?

@deldeek 4 жыл бұрын

Good video, we had to replace a starter on a Nissan Armada and I noticed the next day the idle was out of whack and it even accelerated slowly on its own and shifts gears , could this procedure of changing the starter and putting things back together have anything to do with this issue ? Thank you kindly

@FalconsGarage 4 жыл бұрын

unless there was something left loose or unplugged there is really no reason why a starter change should effect the drive of the car

@deldeek 4 жыл бұрын

Falcon's Garage he left one of the hose unconnected it was leaking vacuum! Thanks for your input

@jonathanwright3055 4 жыл бұрын

Ok I have a 2006 nissan maxima 3.5 its putting out code p0507 I tried your video step by step with you and the check engine light never blinked can there be anything else I need to do?

@FalconsGarage 4 жыл бұрын

You can try taking it to the dealer or get somebody with a tech 2 scanner to program it.

@Sam-mq5rh 6 жыл бұрын

I have a 02 Infiniti Qx4 it doesn't want to start when the engine is cold without pressing the accelerator some just enough to bring it to 5-600 rpm.. After giving it gas for just few seconds it runs fine at normal rpm. After engine is warm the car will start all day long.. Everytime I search this is what comes up.. Any thoughts.. Is it my TBS?

@FalconsGarage 6 жыл бұрын

sounds to me like you have a dirty throttle body

@Sam-mq5rh 6 жыл бұрын

Falcon's Garage thank you.. I'm going to clean that bad boy up and hope for the best.

@lnkee 2 жыл бұрын

A lot of people here are talking about when they cleaned their throttle. I thought only when you disconnect the IAC Valve electrical connection, you need to do the reset. Am I getting confused here? So you need to do this even when you clean the throttle head? I am not removing any electrical wires to throw off the computer setting. I had mine sprayed and cleaned when I found a crack in the intake valve hose and removing the hose only. I appreciate your response. Thx

@FalconsGarage 2 жыл бұрын

it just depends when your code comes on .. code could come on after cleaning OR after disconnecting

@tonycervantes4816 2 жыл бұрын

@@FalconsGarage my code is p0507. What code it is.

@constantinoliberato8171 7 жыл бұрын

hey I have a Nissan sentra 2007 I clean my throttle and a check engine light turn on. now I get a p507 when on idle is on 1800-2000rpm I try reseting it but it wont work

@FalconsGarage 7 жыл бұрын

keep trying it, tr it when the engine is cold and then again when its hot, ive seen it work on both instances

@flowerdeliveryservice 7 жыл бұрын

I did a tune up and cleaned the throttle butterfly with battery connected and got the code too. I tried doing the relearn on a friends expensive scan tool that said it does it, but p0507 came back. Now if i try this procedure ('service engine soon' already on). should i clear the dtc first then do the relearn or leave dtc stored with light on and do relearn....OR does it not matter. Thanks!

@FalconsGarage 7 жыл бұрын

you can clear it before or after it doesn't really matter

@rolandomotadelcampo7168 4 жыл бұрын

Is the code supposed to delete by itself?i got the blink indicator and everything i cranked the engine when the liggt turned solid

@FalconsGarage 4 жыл бұрын

for the most part it usually deletes it self after driving it for a while.... or you can always clear it your self with an scanner

@freestylemike3445 2 жыл бұрын

Will it work on a 2004 Nissan frontier

@FalconsGarage 2 жыл бұрын

yes

@viktormora5260 3 жыл бұрын

Great video but how do i fix a vacum leak??

@FalconsGarage 3 жыл бұрын

Viktor Mora well you got to find the leak first and then replace what ever house or gasket it’s leaking.

@tommy9422 3 жыл бұрын

I have a push start would I still do the on off 3 times before hittin the gas

@FalconsGarage 3 жыл бұрын

yes.. just dont turn it on

@oscarcenteno1976 6 жыл бұрын

Will having this code let me pass smog ? And where is your shop located ? Hopefully it’s near me .

@FalconsGarage 6 жыл бұрын

depending on your state.. smog should be ok .. but most stated wont pass inspection with the check engine light

@tyrellgatling5666 6 жыл бұрын

Do your ses light have to be reset first?

@FalconsGarage 6 жыл бұрын

it dosent have to be "first" but it does have to be reset.. or it will reset itself after driving it

@tracydsg 7 ай бұрын

My Nissan is a push button start. Also the idle drops, not high.

@jesismith9863 6 жыл бұрын

I had the throttle body cleaned on my '07 Nissan Versa and now the RPM's are jumping from 1-2. Do you know if this procedure will work? I don't want to spend the money on a new throttle body if I don't have to.

@FalconsGarage 6 жыл бұрын

yes this procedure might help you!

@djs882 5 жыл бұрын

cHECKED tHE o rING iNSIDE tHE tHROTLE body

@scottbradley3486 4 жыл бұрын

Can this be done with push start

@FalconsGarage 4 жыл бұрын

Yes. Same procedures apply.

@salomezavala597 7 жыл бұрын

I have a 2004 Nissan Altima and I tried this procedure like 10 times and I can't get me engine light to blink. I've done it at the same time as I watched the video also. I cleaned the throttle body. What am I doing wrong?

@FalconsGarage 7 жыл бұрын

could be Bad throttle body. or computer

@fjlenco 2 жыл бұрын

I know is a bit late, but did you find out what the problem was, im having the same problem, my check engine light wont blink during the relearn, I'll appreciate it if you can help me out.

@Cheesedrip268 6 жыл бұрын

This could work on the nissan Pathfinder 2006??

@FalconsGarage 6 жыл бұрын

yes

@smittywerbenjaegermanjanse8340 2 жыл бұрын

Does this procedure work on push ignition Nissan Altima's? I have 2011 with this code currently

@FalconsGarage 2 жыл бұрын

yes

@Jekyll_Island_Creatures 6 жыл бұрын

What should the rpm be when it's running correctly?

@FalconsGarage 6 жыл бұрын

600-700

@mmorton1227 2 жыл бұрын

I'm not trying to skip out on the process but would clearing the codes work too ?

@FalconsGarage 2 жыл бұрын

@shannonwetnight9389 7 жыл бұрын

P1122 and P1126, eratic idling, CEL and VDC Off...? Replaced throttle body and relearned virtually everything and cleared codes, still get P1122 and P1126 on startup. Starts up perfect and then the lights come on and the idle goes either low constant or all over the place between 750-1650. Any ideas?

@FalconsGarage 7 жыл бұрын

make sure there inst a vacuum leak somewhere as well and I would start checking the wiring system

@shannonwetnight9389 7 жыл бұрын

Falcon's Garage Thinking it's the throttle control relay. If that fails, it throws both codes. When I start it up, I can hear a crackling noise in the area where that relay is located. I'm guessing that if the relay fails, it can't communicate with the throttle body, and thus the codes for both the circuitry and the throttle body itself will display. Does that sound about right or am I way far off?

@shannonwetnight9389 7 жыл бұрын

I should add that it sounds like the relay is spark gapping.

@FalconsGarage 7 жыл бұрын

Shannon Wetnight that sound could also be the replay engaging. When ever the engine is off but the cars ignition on you should be able to press the gas pedal and the throttle body should engage check that it does also. Also see call the dealer and see if there is a computer update on your car. Sometimes they develop glitches on the computer and an update fixes it.

@Alyngiht 7 жыл бұрын

thanks ill try this out and if i fuck it up ima throw this car off the tobin boston bridge lol

@FalconsGarage 7 жыл бұрын

lol

@JasonSmith-qx3zh 4 жыл бұрын

I know what you mean it's like its built to be a money pit cheap car but they make up for it just to get to serviceable parts. You have to order off the net because the local parts here in the bham are like gran thief!