FID Racing Pull Start and 990 Carb How-To Starting Procedure

Рет қаралды 3,175

5 жыл бұрын

Just a quick procedure of how to start the 990 carb and how easy it is to start any engine with the FID Racing pull start. Hope this helps somebody out there. Enjoy!

Пікірлер: 56

@pdiddy8509 3 жыл бұрын

I know this is probably an old post but this was very helpful bro. Ive been plagued with gas rc issues and still am but i tried a couple of these tips and works a lil better now but i still have no consistency as far as having my engines start reliably everytime. Theres always some issue every coupl etimes i go out to run. mostly failure to start. Thx

@CrucialRC 3 жыл бұрын

Glad to hear that I was able to help ya out! If she wont start after running for a while, check the primer bulb. If she's empty then shes running lean and the fuel is boiling before making it to the engine. Let her cool off then richen the needles and run her again. If the plug is wet after running, then put a new plug in and lean the needles. It's like a give or take relationship. LOL

@pdiddy8509 3 жыл бұрын

@@CrucialRC I followed ur vid and my 1107 Carb starts right away but Im having a hell of a time with my engine that has the 990 Carb on it. Its intermittent sometimes itll start and run at other times it wont. Ive change out everything. Coil, Spark plug, etc. but it seems like its not sparking. ive gap it correctly changed out the push buttoin killswitch. I even removed the SuperBee killswitch to rule that out but im still getting intermiitent results. You seem to know what ur doing LOL. Any suggestions??

@CrucialRC 3 жыл бұрын

@@pdiddy8509 seems like you've covered all the electrical bases. You sure its not fuel related issues? Stock settings on carb? Primer bulb full when trying to start? Fuel lines on the right way? Gotta check all the elementary stuff 1st. Good luck!

@pdiddy8509 3 жыл бұрын

@@CrucialRC Nope. Not fuel related as far as i can tell. fresh fuel mixture. Runs fine one day then wont start the next or sometimes wont start after running the same day. Weird. I think its electrical but i cant isolate it. yes Ive checked all fuel lines, filter and set carb back to default settings but it stiil exibits same weird symptoms. I have a new knock off 990 carb i ordered from ebay that i thought was a walbro im gonna install see if that solves the problem although i still think the problem is electrical.

@CrucialRC 3 жыл бұрын

I'm a little stumped bro. Did you use a genuine zenoah coil when you replaced it? If so I guess just make sure all your connections are tight. I always crimp down on my coil connections to make sure they are nice and tight when I put on the killswitch. To me it seems as though they are always a little too loose for my liking.

@Tomberland84 3 жыл бұрын

My RC cars with a 990 carb are a b*tch to start in the winter time. I think I'm going to switch them all over to a 1107. I've heard good things about the 1107 anyways, they have a slightly larger air intake also! Nice video of your starting techniques. Very interesting stuff :)

@CrucialRC 3 жыл бұрын

Yeah the 1107 is easier to start but both are great carbs. Most of my big blocks don't have primer bulbs or choke so im used to it. Thanks for watching!

@DougStarRC 4 жыл бұрын

Hey man crucial 👍🏻 you got that all covered 👍🏻 nice one

@CrucialRC 4 жыл бұрын

Thanks Doug. There's a lot of mistakes people make when trying to start the 990, but its not that difficult. Now the FID is crazy easy to use. I wonder how it would work with the 990 tho??

@DougStarRC 4 жыл бұрын

Well🤔 you'll have to give us a demo👌

@highdesertaggrorc7801 4 жыл бұрын

Oh hell yeah, I love watching these start! I'm curious now if my stock 668 carb would be easier to deal with than a modded 990? I have to say once the model is running a 990 kicks ass! But I never gave the 668 a single chance! Maybe I should just to try it!

@CrucialRC 4 жыл бұрын

Carbs don't cost that much and it doesn't take long to swap out. Give it a try👍🏾

@TruSwagTv2 4 жыл бұрын

Those 2 beast beautiful I absolutely love them nice upgrade RcFam4Life #trufam4life 🤜🏾🤛🏾💯🙌🏾🤙🏾👊🏾🤝✊🏾

@CrucialRC 4 жыл бұрын

Thanks Arrma King👍🏽

@zeeshanhb9520 4 жыл бұрын

Now that's what you call an easy start, not that Rovan 20 pulls lasting head ass 🤣🤣 anyways, great video as always Crucial 🤘

@CrucialRC 4 жыл бұрын

Thanks Z👍🏽 Yeah the FID was expensive when I bought it but is nice.

@Ryan-gf3jf 3 жыл бұрын

Great vid! I was planning to get that have u tried the Turtle racing pullstart? Will the FID work on the big bore motors?

@CrucialRC 3 жыл бұрын

I've heard bad things about the TR pullstart so I never tried one. To be honest, I don't even use the FID anymore since I put a big block on my vekta. A regular pullstart does well for me. No, the FID will not work on a big block engine, Ryan.

@Ryan-gf3jf 3 жыл бұрын

@@CrucialRC Thanks for the info! Keep u the great vids!

@CrucialRC 3 жыл бұрын

Thanks brotha!

@mc83ssls1 5 жыл бұрын

Uno 💯👍🏾👍🏾🍻

@CrucialRC 5 жыл бұрын

My man!☝🏽

@michaelinzitari 3 ай бұрын

So the 1107 has choke and primer and you used both to make starting easy. The 990 has no choke or no bulb? I noticed you didn’t use either and still started using slow pulls method. Thanks!

@michaelinzitari 3 ай бұрын

If the 990 has no choke, why didn’t you prime using bulb?

@CrucialRC 3 ай бұрын

It's actually called the purge bulb. It's only function is to purge the fuel lines of air. The slow pulls on the 990 pulls fuel into the cylinder via vacuum. I'm sure I purged the lines on the 990 before the slow pulls. Maybe I edited it out? Lol I can't remember. That was a long time ago. I'm making videos now on how to start a 2 stroke. Keep an eye out and thanks for commenting.

@CrucialRC 3 ай бұрын

@@michaelinzitaricheck out at 1:52. I mentioned pushing the purge bulb until fuel is going thru the line

@michaelinzitari 3 ай бұрын

@@CrucialRC thanks for this info! I will watch the new video when it comes out

@CrucialRC 3 ай бұрын

@michaelinzitari no problem 👍🏽

@geejayrc9401 4 жыл бұрын

Hi mate, have you tried the FID pullstart with a 990 carb, and how is it holding up. Have you ever used the Turtle v2 pullstart? I'm tossing up on which one to get for my OBR full mod reed engine with a 990 carb

@CrucialRC 4 жыл бұрын

Sorry, I have not. Never used the TR but on largescaleforums.com they don't speak kindly of it. Sorry I can't be of any help bruh.

@geejayrc9401 4 жыл бұрын

@@CrucialRC Ok no probs, but how's the FID one holding up then?

@CrucialRC 4 жыл бұрын

@@geejayrc9401 I love it. It makes starting the Vekta a breeze.👍🏽

@chrislrocks 4 жыл бұрын

I have the TR pull start V2 in my OBR full mod reed in my Vekta. It sucks, requires regular maintenance, spring has broken twice. The dog legs wear pretty quickly and need to be shimmed. Consequently that's what brought me to this video. I'm tired of messing with it.

@geejayrc9401 4 жыл бұрын

@@chrislrocks I ended up buying the Killer RC pullstart with the steel cable, and got the DDM alloy pawl. I haven't had a problem since :)