I just watched your video on how to build the nano goblin. I bought this radio online and searched how to set up and this was the first video that came up. I literally couldn’t have set up my plane without you, thanks 🙏🏻
@alanmearns28694 жыл бұрын
Excellent stuff Andrew. Great that you're supporting the i6. It's a very capable radio and not just for beginners. Good to have such a capable budget option.
@easonliu6003 жыл бұрын
Wait does this receiver require a 5 volts receiver battery? Or can it be 4.8 Volts, 6 Volts, ect. Just askjng
@jezykwkosmosie Жыл бұрын
@@easonliu600 RX doing well with 4.6V in my case, didn't try 6 though.
@JohanBesterphotos4 жыл бұрын
This is a lifesaver! The manual doesn't make this clear at all! Please give us more of this.
@aggrobert84904 жыл бұрын
Next vid maybe Lil bit advanced How did I got to 10 channel/function 🤔
@AndrewNewton4 жыл бұрын
I have a whole playlist for this radio. 10 channel mod needs a Windows PC which I don't have
@GrandadIsAnOldMan4 жыл бұрын
Thanks Andrew, straight forward and covered the options clearly. I shall save this one in my FlySky playlist 😍👍
@easonliu6003 жыл бұрын
Hey does the receiver require a 5 volt battery? Or can it be 4.8 Volts, 6 volts, ectm
@GrandadIsAnOldMan3 жыл бұрын
@@easonliu600 if you are asking Andrew it is better to start a fresh comment. If you are asking me then the answer is that you usually power the receiver via the ESC (electronic speed controller) which manages the main battery for the motor. That generally has a circuit on board that provides the correct 5 volts for the receiver. You would have to check the specifications for your receiver to see what range of voltage it will work with but generally 5 volts with a range either side. I have run them from 3xAA batteries with no trouble but I never fly at maximum range so I don't know how much it would affect the range.
@easonliu6003 жыл бұрын
@@GrandadIsAnOldMan well I need to start the reciever. Like the first time when im trying to connect the receiver to the transmitter. On youtube, alot of people use 5 volt batteries to power up the receiver. So idk
@easonliu6003 жыл бұрын
@@GrandadIsAnOldMan i understand that the Reciever runs on the battery and the esc, but when im trying to connect the reciever to the transmitter, do i need a 5 volt battery
@GrandadIsAnOldMan3 жыл бұрын
@@easonliu600 do you mean just for testing purposes, without the rest of the RC equipment, like the ESC and servos? If you are not connecting anything else to the receiver, then yes it would need battery power to run. If you are not going to use an ESC then you would need to read the instructions that come with the receiver and check what voltage it states it works on. Generally they run on 5 volts but my disclaimer is you need to check that for yourself. If you are using an ESC with a BEC you do not require a separate battery for the receiver. The BEC part of the ESC circuit converts whatever voltage the battery is, down to the 5 volts required for the receiver. I would recommend you watch the FliteTest beginners series, they have an excellent set of videos that cover the whole range of information to get you flying - it would also give you the general information that would apply to RC cars and boats as far as the RC gear is concerned.
@ladraode9dedos4094 жыл бұрын
Have one of those and have to say they are no bad at all! Pretty decent and very well suited for low budget/kids trainer!
@hexagon_is_best_shape7 ай бұрын
This is such a great explanation. Was having trouble figuring it out. Thank you very much!
@AndrewNewton7 ай бұрын
Glad it helped!
@TentoesMe2 жыл бұрын
You're the first to show me how to SAVE the model name... HOLD the cancel.
@AndrewNewton2 жыл бұрын
It is a strange way to save, glad you got it.
@ARMY_RUGS2 жыл бұрын
BEST N SIMPLE VIDEO EVER
@gamingwithryan29363 жыл бұрын
I’ll be pairing this to a micro adventure pnp. Thanks for this video.
@Billbobaker4 жыл бұрын
My best friend just loves his "flysky" type radio.. I think his is a Turnigy brand one.. I've left them all for the Open Tx type now, Taranis and Jumper and have never looked back. He swears by them but nearly every drone comes bind and fly with frsky as an option and maybe DSMX.. so few come with flysky.. This is a very easy menu and intuitive to follow.
@julianhumphrey48434 жыл бұрын
Excellent video Andrew, this is still my choice of radio, got 3 of them, they work well for me......and very good point about NEVER reverse channel 3 throttle
@nickvledder Жыл бұрын
Exactly the channel which must be reversed on many Futaba-transmitters!
@one44east774 жыл бұрын
Thank you so much for your information. After a long period of being away from flying model airplanes you have made it very enjoyable getting back into flying again.
@AndrewNewton4 жыл бұрын
Glad it was helpful!
@DavidHeetderks3 жыл бұрын
very helpful 👍
@chrisl499919 күн бұрын
Simple, great explanation. Thanks
@AndrewNewton19 күн бұрын
Glad it was helpful!
@MrVasmikey4 жыл бұрын
Great teaching Andrew as always.
@easonliu6003 жыл бұрын
Wait does this receiver require a 5 volts receiver battery? Or can it be 4.8 Volts, 6 Volts, ect. Just askjng
@FPVUniversity4 жыл бұрын
I had one of those.... only branded as Turnigy. And to be honest, for the price it was just fantastic!
@AndrewNewton4 жыл бұрын
The limitations are a bit frustrating but performance and range is excellent.
@easonliu6003 жыл бұрын
Wait does this receiver require a 5 volts receiver battery? Or can it be 4.8 Volts, 6 Volts, ect. Just askjng
@fanBladeOne2 жыл бұрын
OMG I cannot thank you enough! You solved my mislabelled wiring!
@AndrewNewton2 жыл бұрын
You are welcome!
@richardpage29884 жыл бұрын
Thanks Andrew as a complete newbie to programmable transmitters your video was most helpful. Regards Richard
@AndrewNewton4 жыл бұрын
Thanks Richard, glad to help
@illwind94298 ай бұрын
Thank you for posting this video. The manual is useless for a beginner and so is the flysky website.
@AndrewNewton8 ай бұрын
You're welcome
@RobisonRacing684 жыл бұрын
Thanks for these Flysky vids sir. We used your other vids this summer to set up and learn my cousins new Flysky. I use this same radio on my quad. It's a pretty nice little radio I think.
@AndrewNewton4 жыл бұрын
Surprisingly good Lauren. Just wish some genius could hack the firmware for more mixes and switches in mixes
@DLM5173 жыл бұрын
i have a 16X and a problem with changing subjects after finishing one subject and ready for the next subject. I copied 34 pages for the 16X. I had success for a good portion. Help from a nooby, thanks!
@jessiejames53733 жыл бұрын
Thanks 👍
@paulwiltshire26764 жыл бұрын
This is great basic advice and just what I needed. Thanks for sharing your knowkedge.
@AndrewNewton4 жыл бұрын
Glad to hear it!
@beefybeef13264 жыл бұрын
Nice video for beginners
@bhushandudhane962 жыл бұрын
Thanks for your information video 👍
@AndrewNewton2 жыл бұрын
No problem 👍
@corbingenious65473 жыл бұрын
THANK YOU
@garywpearson1955 Жыл бұрын
Awesome! thanx so much
@AndrewNewton Жыл бұрын
You're welcome!
@alasdair41614 жыл бұрын
I have the X version of this radio that I like for lots of builds, I bouce between this and a Taranis but for many things like boats and basic planes the i6x is my preferred option. Receivers are cheap, they get amazing range and some, like x6b offer basic telemetry with alarms. A great reliable budget radio.
@AndrewNewton4 жыл бұрын
Are there more mixes available with the X or with firmware hacks?
@alasdair41614 жыл бұрын
@@AndrewNewton It does have up to 3 mixes available with each model, and each with full offset control etc. I haven't needed to play around with the firmware but it was tempting to do the RSSI mod (sending RSSI up a spare channel for OSD) but I really don't need it for what this radio does. One additional thing the X has over the non X is 3 way options for all switches, and I believe they are full sweep inputs, allowing additional pots or multi way switching to be fitted in their place. I changed all four switches to 3 way early on.
@Kaialadavi2 жыл бұрын
Thx, u helped me so much
@AndrewNewton2 жыл бұрын
No problem!
@franciscourena56362 жыл бұрын
**** RESPECT = Great presentation
@AndrewNewton2 жыл бұрын
Thanks, it's an excellent radio
@Urza14 жыл бұрын
Your video helped, thank you. Now I can start making RC videos on my channel ;)
@AndrewNewton4 жыл бұрын
Hey Urza, great 3D printing videos on you channel already. Subscribed
@easonliu6003 жыл бұрын
Wait does this receiver require a 5 volts receiver battery? Or can it be 4.8 Volts, 6 Volts, ect. Just askjng
@schlechtestergtaspielerdek38513 жыл бұрын
Wich type of battery did you use for the reciever. Cause on the recceiver it says 4V-6.5V but I littraly cant find any battery pack in that range. Only 3.5V 7.8V. But I think those arent gonna work. 3.5V is just gonna be to less and 7.8V is probably going to fry my receiver. Could you link the battery you used?🙏🙏
@AndrewNewton3 жыл бұрын
NiMH pack of 4 x AAA
@Rhoedision4 жыл бұрын
Awsum bro thank you so much..
@easonliu6003 жыл бұрын
Wait does this receiver require a 5 volts receiver battery? Or can it be 4.8 Volts, 6 Volts, ect. Just askjng
@johnmoss41402 жыл бұрын
Just wanted to say Thank You for your videos. I'm a rank beginner and I recently visited a local flying club (they've got a fantastic model airfield !) and I asked about the FS-i6x (which I'd seen on KZfaq) and I was told "no no no" you must buy at least a Spektrum or Futaba, not that the Flysky isn't a capable radio but you have to be a programmer to use it". I was disappointing to say the least. The Spektrum has less channels and cost 4x the price! My only concern with the i6x was that it only had 3 mixes and I wanted to do differential thrust but after seeing your video on programing differential thrust I think I'm going to get a Flysky. I want to build a true Flying wing based on Al Bowers Prandtl wing design and although it shouldn't "need" differential thrust to overcome adverse yaw it certainly won't hurt it's performance to have it. Again Thank You for sharing your knowledge. I certainly appreciate it!
@AndrewNewton2 жыл бұрын
Thanks John. Club mentality is too restricted for me too. FlySKY programming is fairly similar to Spectrum, but FrSKY programming can be more complicated but way more capable flexible.
@antoniecolisao90318 ай бұрын
It is compatible with 4ch rc helicopter with mix speed controller tail motor and main motor connected together
@AndrewNewton8 ай бұрын
Not my area of expertise sorry
@Rubydude Жыл бұрын
hey! This is an amazing video. I'm a complete beginner and am building my first rc plane. This is probably a super dumb question but i was wondering how I power the receiver. Do I need to get a separate 5v battery to connect to it?
@AndrewNewton Жыл бұрын
Can use 5V battery or more commonly the ESC includes a voltage regulator that reduces the main battery voltage down to 5V (thin red wire) Explained here kzfaq.info/get/bejne/btCVa5dhxMu5lIk.html Also check out my RC Basics playlist
@lasersbee4 жыл бұрын
5:38... Actually the beeps sequence only lets you know that the ESC is initialized... It does not let you know that the rest of the Radio or Motor connections are correct.
@omtodkari27362 жыл бұрын
For some reason the last long beep is not playing. I'm trying to troubleshoot, but unable to find out what's causing it, is it esc or receiver's fault?
@lasersbee2 жыл бұрын
@@omtodkari2736 Different ESC manufactures can use different Beep Sequences on boot up of the ESC. Or your Throttle could be reversed.
@crazycrab85784 жыл бұрын
I have meet a few people with this TX, and me, best thing for price, but getting spare Rx can be a problem
@alasdair41614 жыл бұрын
The receivers ars cheap with lots of variants available.
@crazycrab85784 жыл бұрын
@@alasdair4161 e bay only, that i know off, I know of 3 variants, but still a problem, but still a very good piece of kit
@alasdair41614 жыл бұрын
@@crazycrab8578 If you're prepared to wait months for delivery and have no warranty, Banggod have them. The i6x radio adds more receiver options with about twelve available.
@crazycrab85784 жыл бұрын
@@alasdair4161 its taken me 3 to 4 months to learn how to use this one, any more options and me brain will explode, at momment trying to upgrade to 10 channel, will get there one day :)
@jaeger96392 ай бұрын
i don't have a servo lead can i just use two channels for the ailerons
@AndrewNewton2 ай бұрын
Yes, use Ch 5 for the second aileron then use a mix with Ch1 as the master and Ch5 as the slave
@unclealig2 жыл бұрын
Hi. I would like to establish a safety feature, so that I can cutoff the motor via a switch. So at every control input of the motor on CH 3, I can shutoff the motor. How to programm that? Make a mix of an unused channel as master with CH3 as slave, then set positive and negative mix to 100% and offset to -50%? Is there any alternative to not occupy a channel for this mix? How about the "switches assign" menu Option, what can I do with that setings? Thanks
@AndrewNewton2 жыл бұрын
Throttle cut programming shown here kzfaq.info/get/bejne/rtplfMeWscrNpZs.html
@mima60295 ай бұрын
Are bind plugs included in the transmitter and reciever purchase ?
@AndrewNewton5 ай бұрын
Yes included. It is just a wire that connects Signal to Ground on the Bind pins. You could make one yourself from a servo cable
@Top-Jimmy Жыл бұрын
Gday from WA Andrew! Top knotch video''s mate, They are very much appreciated. I think this is the first question I've asked you. I am now into RC Sailing as as we get on, For SOME of us its time to slow down a tad. Mate, My question is, Would this Radio be suitable for say 300 meters transmission distance across the ocean water? Also, Would the stock receiver be enough, or are there any you can suggest with an external antenna? if I need to, I can extend the battery wires and tie to the back stay of the Sailboat. If the stock receiver is sufficient, Would the signal penetrate blow molded plastic without any problems? - Looking forward to your reply mate, Take care from WA.
@AndrewNewton Жыл бұрын
Might need to ask RC sailors what they use. I havent gone more than 50m out but my mate Allen uses this radio for his yachts. 300m would be pushing it I suspect. 2.4GHz range is greatly reduced over water
@Top-Jimmy Жыл бұрын
@@AndrewNewton Thanks mate, Shall do. Can you recommend a 5.8GHz Radio and receiver under 250 bucks?
@AndrewNewton Жыл бұрын
@@Top-Jimmy 5.8GHz is only used for video, not RC control.
@nickvledder Жыл бұрын
2:53 that ‘s why in many Futaba transmitters one has to reverse channel 3. And Futaba is still in business, can you imagine?
@AndrewNewton Жыл бұрын
Madness!
@allanduncanson28163 жыл бұрын
Another great vid. Thanks. I noticed that the Tx shows the voltage of the Rx when connected. Is that standard or a mod? Seems like a good idea.
@AndrewNewton3 жыл бұрын
Standard with the i6A and i6B receivers
@user-vt3or6go7i Жыл бұрын
my remote did not soh wnay of the setup stuff
@some_guy155 Жыл бұрын
i plug the binding cable but when i plug the battery (i actidentally put the battery cable up side down and the battery is 2S(7.4V) 900 Mah) my receiver started smoking and when i tried again it stated melting and when i try to flip both of the cable and putting 30A esc it worked but the smoke started after 30 sec so after that i put the cable in the right position and i plugged the esc it finally worked fine. should i just buy a new receiver? i hope too that this would be a great warning to the beginners out there
@AndrewNewton Жыл бұрын
I would replace it if it was smoking. Amazing that it still works
@some_guy155 Жыл бұрын
@@AndrewNewtonalright then i will buy a new receiver, Thanks
@easonliu6003 жыл бұрын
Where can i find a 5 volt battery? or starting up the reciever?
@longjammeriii33234 жыл бұрын
Hi Andrew very well explained which is much appreciated by an old (71yrs) newbie to the hobby, can you help with how to add a 3 axis gyro such as A3 V2 stabilizer to a 4 channel glider, do you just add it in between the rx and the servos or is it more complicated than that, thanks in advance for your much appreciated advice, regards Alan, uk.
@AndrewNewton4 жыл бұрын
I dont know that stabiliser but it would control the servos and the receiver just sends the stick movement signals to the gyro. Usually no mixing is used on the transmitter.
@longjammeriii33234 жыл бұрын
@@AndrewNewton thanks for the help and advice Andrew I now feel more confident about connecting stuff together, much appreciated my friend, regards, Alan, uk
@joelzwerk41622 жыл бұрын
Thanks very much for the videos. Really informative. Anyway, I've been flying rc for quite a number of years and just bought the Turnigy version of this radio. You mention several times to never reverse the throttle servo. I fly glow powered planes and just wondered if this might also be true for them. I can see not reversing with an electric plane. I wondered if there might be some sort of fault with the radio if the throttle servo is reversed. Thanks in advance.
@AndrewNewton2 жыл бұрын
Thanks Joel. I was talking about not reversing the throttle channel on an electric model. I guess on a gas plane the throttle servo could be either orientation, so reversing the throttle channel might be required.
@joelzwerk41622 жыл бұрын
Andrew, Thanks again for the reply. I didn't think the reverse would matter with a glow engine but just wanted to be sure. I just could not justify spending bunch of money on a new Spektrum transmitter. I still use my original DX-7 which I purchased shortly after they came out. Seems to me like a lot of these companies are doing their best to price themselves out of reach of the average fellow. Just my opinion, and I really like my old radios. Anyway, thanks again for the reviews and other videos. Great information.
@thebunkreport Жыл бұрын
What is the purpose of using a separate battery to bind it up?
@AndrewNewton Жыл бұрын
Convenience mostly, and it's a bit safer than using the esc maybe.
@thebunkreport Жыл бұрын
@@AndrewNewton I would think that it would be much safer to use the power through the esc.
@kennethholland4627 Жыл бұрын
I need help! I have a Flysky I6X transmitter to control my tracked inspection bot. But when I first switch the transmitter on, it beeps and gives me this message: "!!WARNING!! Place all switches in their up position and lower the throttle" Sometimes I just bump my left toggle switch, channel 3, and it stops the warning and gives me full control. But all too often, it doesn't matter how many switches and toggles I move around, it just keeps beeping and will not give me control. What is it doing and how do I get it to stop? I have a simple tank chassis with a light and camera gimble on it. It's not like I need a safety switch to start with. Can you help me?
@AndrewNewton Жыл бұрын
Throttle has to be full down and switches all up or back to avoid the alert
@kennethholland4627 Жыл бұрын
@@AndrewNewton Yeah. I had tried all that and it seemed to make no difference what I did with the switches and throttle. But funny thing, now that I asked for help, it went back to working normal again. You suppose it was just embarrassed and decided to just start working again?
@AndrewNewton Жыл бұрын
@@kennethholland4627 How odd! Might mean one of your switches is not switching
@PilotElias4 жыл бұрын
Very helpful video. Cheers! May I ask how much you paid for the technical things like remote, esc, receiver, etc.?
@AndrewNewton4 жыл бұрын
Product link in the description.
@jayotayco43077 ай бұрын
Is this compatible with the Eachine bf109 mini rc plane?
@AndrewNewton7 ай бұрын
No, this radio only works with FlySKY AFHDS receivers. The Eachine bf109 comes with it's own radio
@vivaanarora71703 жыл бұрын
Sir if we use 2servos for the elevator (as you did) so how will I be able to reverse one of them
@AndrewNewton3 жыл бұрын
Only one servo for elevator. Do you mean Aileron? Just reverse the channel that the servos is connected to, or mount it the opposite orientation to the other one.
@MissingRedacted2 жыл бұрын
im new to a lot of this stuff, but whats the highest volt battery you can use?
@AndrewNewton2 жыл бұрын
It uses 4 x AA from memory
@olivernguyen98494 жыл бұрын
some people said it will work if I use my normal batterie and an ESC with a built-in BEC will that work? if not can you pls give me a link for the batterie. thx
@AndrewNewton4 жыл бұрын
Correct. BEC or the is the normal way to power the receiver and servos. Most ESCs have a built in BEC or you can use a separate BEC
@a.sanusinazareth9213 Жыл бұрын
Hello again, my TX fs-i6 can not center and make my arduino drone rotate unstable. I tried to reset, reset factory even adjust the stick - but failed. I try to use my friend's TX and everything is okay. Do you have link to fix the fs-i6 which the stick is not center. It is yaw. Throttle, pitch and roll stick is okay. Please recommend me for better TX with the same price of fs :)
@AndrewNewton Жыл бұрын
No idea about Arduino or drones. Cant you just change the yaw channel mid point. Radiomaster TX12
@a.sanusinazareth9213 Жыл бұрын
@@AndrewNewton okay thanks
@tracyfenton70294 жыл бұрын
Can you do a video pairing this with a FC, I have this TX with no knowledge of how to do anything with it aside from the basic tx to rx bind
@AndrewNewton4 жыл бұрын
Yes I will eventually. Have a look at the FlySKY playlist for programming tips - kzfaq.info/sun/PLC8MdCMvxwBg-OAlBiYWuDSBSpyFMFhy5
@grumpyjohntxredneckrc63464 жыл бұрын
I Seen This FS-i6 TX w/RX On eBay Recently For $50, Also A FX-6iX? Then A FS-9TH w/RX+ Back Module For $77? They Seem Like A G@@D Deal, Butt I've Never Used Any!? Especially Compared To Costs Of Outragious $$$ Spektrum Stuff? Thanks Mate
@iridiumnight37502 жыл бұрын
Plugged a 1s 3.4v lipo into it for power and it popped and started smoking.
@AndrewNewton2 жыл бұрын
OK thanks, I won't do that
@olivernguyen98494 жыл бұрын
Thank you! do you have any recommended batteries that are 800mah and 11.1 v with 3s and 20c if so pls give me a link:)
@AndrewNewton4 жыл бұрын
No. Search on HobbyKing
@olivernguyen98494 жыл бұрын
@@AndrewNewton thx
@christophertaylor7647 Жыл бұрын
how do i limit throttle on ch &2?
@AndrewNewton Жыл бұрын
Dont think you can do that with this radio
@caroltubman86783 жыл бұрын
Hi Andrew, great video, I have purchased a Turnigy TG-i6 radio which looks identical to the Flysky , I have been given a glider which I’m setting up however there is no Turnigy receivers available will the Flysky receiver work with the Turnigy radio. Receivers TGY-ia6. FS-ia6b
@AndrewNewton3 жыл бұрын
Yes they are the right receivers. Exactly the same radio just with a different badge as far as I know.
@skaterboi84942 жыл бұрын
Does this radio use analog or digital servos?
@AndrewNewton2 жыл бұрын
Both, radio doesn't care
@skaterboi84942 жыл бұрын
@@AndrewNewton many thanks
@brianhawkins29532 жыл бұрын
With two broken switches.will it function
@AndrewNewton2 жыл бұрын
Yes, switches are not essential
@brianhawkins29532 жыл бұрын
It won't stop beeping,because of the two switches
@brianhawkins29532 жыл бұрын
Is there a way to reset it.and just use a and d switches
@kevinvandenberghe58298 ай бұрын
WhatsApp the name of the batery IM looping but I find always White 2 holes
@AndrewNewton8 ай бұрын
Odd translation?
@kevinvandenberghe58298 ай бұрын
@@AndrewNewton yes I m looking for a batery for the reciever
@AndrewNewton8 ай бұрын
@@kevinvandenberghe5829 4 x AA
@evilgenius973 жыл бұрын
Im going to guess my battery that too hight voltage is why i cant get any functionality
@AndrewNewton3 жыл бұрын
Radio battery too high?
@evilgenius973 жыл бұрын
@@AndrewNewton Later on i think i learned yes. 7V battery 3V ESC
@simmyabis73304 жыл бұрын
Is there a way to use ailerons withouth y connector?
@AndrewNewton4 жыл бұрын
Yes, look in my i6 playlist for flaperons mix
@simmyabis73304 жыл бұрын
@@AndrewNewton thanks
@olivernguyen98494 жыл бұрын
what battery do you use for the 5v
@AndrewNewton4 жыл бұрын
4 x AA NiMH pack with a servo plug. Mine came from Hobbyking
@edgardelacruz255411 ай бұрын
How to order and how much
@AndrewNewton11 ай бұрын
Mine is not for sale
@chrisgiles53893 жыл бұрын
how many models memorys does this have?
@AndrewNewton3 жыл бұрын
20
@pinlock43314 жыл бұрын
What is default, real range?
@AndrewNewton4 жыл бұрын
I would guess 1.5km but it totally depends on the level of RF noise where it is operating.
@craigrpennyify4 жыл бұрын
Great video Andrew. I have this tx and very happy with it. But I'm having difficulty with mixing Chanel's on a glider, basically trying to use alrons without using a "y" lead. Any help or suggestions. Many thanks...
@AndrewNewton4 жыл бұрын
Separate aileron channels is covered in my Flaperon mix, see the FS-i6 playlist
@easonliu6003 жыл бұрын
Wait does this receiver require a 5 volts receiver battery? Or can it be 4.8 Volts, 6 Volts, ect. Just askjng
@mehdielkhatib10884 жыл бұрын
Does this work on the f15 jet 70mm 4s
@AndrewNewton4 жыл бұрын
Yes as long as you have a FlySky receiver
@mehdielkhatib10884 жыл бұрын
Andrew Newton it says dms/dmx watever. So yea???
@AndrewNewton4 жыл бұрын
No
@ISSOU-if7df4 жыл бұрын
What is the rc plane ?
@AndrewNewton4 жыл бұрын
Volantex Ranger G2 - bit.ly/2JXGYsn
@avsaase4 жыл бұрын
Thanks Andrew. I sold this radio to buy a Taranis Q X7, but I'm considering buying a X9D+ 2019 (non-SE) to have some more switches and the sliders. Can you do a review of that radio?
@AndrewNewton4 жыл бұрын
Would be worth reviewing, maybe in the future.
@matthewbarger45924 жыл бұрын
i feel sick
@AndrewNewton4 жыл бұрын
Fever, cough?
@matthewbarger45924 жыл бұрын
@@AndrewNewton Actually trying to decide what radio I want. If I only had a million bucks id buy them all! Great video buy the way. I enjoy your channel.
@AndrewNewton4 жыл бұрын
Taranis QX7 if you can afford it, or this one if you're on a tight budget. Both have excellent range and programability.