Channel mapping still not working

Out of the countless hours of research and no one to show me what I was doing wrong,by far you have been the most helpful!! hands down,thanks

Thank you so much. Your video fixed my issue that I had been working on for hours!

built my 1st quad set it all up then found that throttle was wrong spent half a day searching for the answer and found this video cheers Brother for the simply fix

Great video, started off a bit rocky, but you recovered and did well! Keep up the videos and fly safe. I am a single engine aircraft pilot and a commercial drone pilot! Good job. Thank you!

I'm digging this review...Thanks for putting it into summary! I had a lot to learn by myself that you covered but much more still to be learned! Very helpful! Through and simplistic!

Thanks so much for the help. Now I’m flying endlessly

This is awesome! Added this to my VERY USEFUL playlist for quad-copters! Thanks!

First time drone user needed help and you did it perfectly. Cheers bro

Thank you so much, I am new to this RC world and your video helped me with my first quad. You are the best!

Thank You for the quick response. JR

The same, fs-ct 6b tx and rx, and yes I have movement in the receiver tab

This helped me so much thanks!!!

Great video Sir, loved the plain speaking easy to follow instructions and just subbed ya!

Thanks man! I've been scratch building fixed wings for several years, but never built or even flown a "real" quad. I have a tinywhoop and like it and was wondering if I could use my radio with a bigger quad... I guess so. Now I just have to build it.....and probably rebuild it a few times to.

Thanks bro most helpful video by far

HELPED ME BRO THANK U MUCH

It really helped me! Thanks a ton

Thanks man, helped me out a bunch!

Thanks for the tutorial! Subscribing for more for sure!! Keep it up!

Great vid. I know it's laughable for most flyers but for us beginners, without videos like this it can be baffling so thank you. Is mode always on ch6 and arm ch5 on every quad though.

Im getting a happy model mantis that comes with one of these i6 transmitters so glad I can bind it to other stuff

your video saved my life. well, someone's life. that thing about holding the cancel button to save settings "everybody knows" - it's not in the manual that i can see.

Hey man I followed your instructions down to the dot but at 9:32 nothing moves in cleanflight like yours does. BTW im glad i found your video Ive been trying to figure this problem out for a while. your video def helped me out a ton so far!

Hi thanks best explained flysky setup

Worked, thx !

Great video, thnx alot man !

Thx good info keep it up

thank u it helped me a lot

Very helpful thanks👍

Great video.. does this work with the eachine novice 1?

thanks for sharing my friend ✌

Helps a lot thanks

Thanks for showing the right way to do things . I have a problem with getting my transmitted to work on screen like you have and my calibrations so off left is right right is left so I need help bad

Awesome video but I need help finding that wire that you connected to the receiver from the drone like when you said make sure not to dod that because the wire was unplugged. Ya that wire i need but I cant find it

great video. does this have DSMX and or DSM2 ? also does it have safe or auto correct for beginner flying ?

Thank you man!

Great vid helped me a lot now that's set do you have any vids on pid settings I'm a newbie so I don't know anything thanks jim

If you still cannot bind like the remote wont say bind ok, your powersupply current might not be enough. I ran 1 amp and it wont bind but as soon as i ran it with a 2 amp charger it will bind instantly

Hi sir , i want to build my drone i have sp racing f3 evo v2 and receiver fs-a8s and remote fs-i6 and motors i solding the board with motors and receiver ,what i should do next ??

Is there a big difference between IA6 receiver and iA6B setup? I got my Wizard in and bound the receiver to it and controller successfully (connected the quad to channel 1 on the receiver), set up the arm switch on the controller (SWD) and tried to power up quad and controller and I'm not getting anything when I flick the arm button. Not even a hiccup. Also no throttle response. Is it necessary to update using beta flight? Or should it at least respond out of the box w the receiver connected to it?

hello! subbed! you are a pinnacle of knowlege. watched 15 vides, FINALLY yours explains it slowly, and understaNDING the concepts. i just got this radio at the thrift store for 2.50 and want to use it my quads. I will order some of the reciever parts that goes to the quads (i got some walkera 250's I want to bypass the Devo 710 and use my F6) I set it up as you instructed. would have never thought of that. thanks man truely, I am learning each day trying not to overspend. I will look for a few cheapie recievers, do they come with the cables to attach? I know i can direct power to a small battery or 4aa, something 4v-6v i immagine, yes>? anyway. tons to learn thanks again.

All set, thx!

Can you bind this controller with the Tinyhawk 2 freestyle?

what digital transmitter is compatable for echine e120 heli

Thanks for share bro

the regular FS i6... can you change the mode 1 and 2 for left or right throttle control ? which mode is most commonly used ? which mode is better ?

can't get beta flight to connect to my multi. running on a Mac, do I need to install a driver or something?

thanks you are amazing

Thanks for your video!! It helped me finally get my modes setup for my Furibee Fuuton 200. I'm stuck with a Eachine branded i6 transmitter, and I can't set the buzzer up. None of the other aux switches work. Plus is there a way to backup or save models if the transmitter get destroy or damaged.

Hi, Angele can you help me set this up for hexell-x in cleanflight, I mean set the flysky.

Will this transmitter work on the Clearview flight simulator ??? ----------- Thanks!

I decided to buy eachine wizard x220 big jump from bugs 3 and 6 do i need to connect transmitter to the computer i can't get it to fly

Yahoooo!! at last, now I switch switches and my micro brushless starts and changes flight modes, its been weeks; no actually its been months and all I could do was scratch my head..Thank you..

Very good 👍☢️

That’s exactly what I’m looking for , one thing - does it work with orange cube FC ?

thanks for the info sir

I am going to be your like number 500. =)

Do you need any extra cables aside from what comes in the box?

Thanks for all your time in posting this. I see you binded to your custom built drone. Can I bind to a Bugs 3 and Bugs 4, or any pre packaged drone ?? How’s that done ?

Thx bro! There has to be one more problem with my setup: In betaflight all the signals from the radio do what they should, so that's fine. If I go to "motors" i can spin the motors, also fine. But when i desconnect my drone from the computer, restart the drone and the controller, i arm it and i set a flightmode, nothing happens. I can only see that the flightcontroller responds to my radio. Can somebody help me out?

RCFlyer85: Nice Video and Thanks. Question on an aspects of FailSafe setup. This was not covered, but perhaps you have experience with also the Failsafe mode. In BetaFlite has two options, 1: fall out of sky, 2: Land In RX (IA6B) Failsafe setup, all six channel can be programed. So if I set say RX channel 3, Throttle in RX to lowest point (Throttle off) on the failsafe setup of RX screen. Suggests to me the Quad will just fall out of Sky. On the other hand, in Betaflite if it is set to land. Which is the Master, I.E. does the quad react to the RX or Flight Controller? Which is superior? Seems it might be the FC but not sure? Thanks BobFlyer

hi i have a few questions i binded my mobula6 quad , i hear a beeing sound from the transmitted all the time and the rx is flashing , how can i turn that off? also in beta flight when i turn the motor stop on , and save the quad doesnt arm at all?

please help. when i bind the rx battery shows up but it just keeps beeping and does nothing

Please help me, I have the exact same receiver and transmitter as you do, but I am using a SPracing F3 Flight controller, I have binded my receiver with the transmitter, I have followed all the steps and I have selected the right configuration settings. However, once I'm at the channel mapping, the throttle on betaflight doesn't move when I move the throttle on the controller

can you use the other type of receiver for this? the stock one it comes with which port? thanks!!!!

How would I change the arm from the left stick to the sw a

Did everything as per the video. I still cant change the values with the transmitter, i.e, in betaflight, the values do not change. p.s: the receiver port on the FC is ppm/sbus, i connected my receiver (the same one that u use) into that. pls help

Hello: Have a question for you that you may help me with???? I'm new to fpv and my wife surprised me with a Eachine Wizard X220 FPV Racer Blheli_S F3 6DOF 5.8G 48CH 200MW 700TVL Camera w/ FlySky I6 RTF and of course there are no instructions that came with it and I have no idea how all this is supposed to work. Now I got to the point where I got the fpv and my googles to work and I was able to pair the receiver with the drone but I can't get the motors to start. So I did some more research on you tube and down loaded Beta Flight and connected the drone with my computer to check out the operation. Well when I tabbed down to the receiver tab and it opened there is no info. According to other posts there are different color horozonal bars that show up to correspond with the different radio controls and would move when you would move each control. Well on my system there are no color bar and no movement when moving the controls. I can't find any instruction on how to go about checking what would cause this problem? So is there any instruction you could give me on how to go about and what to check so I can make the controls work, I think if I can figure this problem out this will fix the problem of the motors not wanting to ture on?. I hope I explained and made sense on my problem. Thanks for your help I watch your channel all the time and have learned a lot so thanks again. John

What happens if my bar isn't all the way full does that mean am not bond please help

Hello Flysky has FS-i6 controller and dron which is flip32 control card. Can you help with flight settings? Thank you

Which Flight controller is used

Oh ,ok so will will this transmitter work with the Rx31d is a DSM2/DSMX compatible 4 channel micro receiver with twin on-board 2A ES ??

Can this be bounded to an Eachine EX2h?

I know this is an old video, but when i get to the receiver tab in betaflight, my sticks are at (A)1537, (E)1527, (R)1504 and my all sticks only go down to 1030-1060... Should i just trim them?

i had successfully bind a8s with fs i6 on my eachine ex110 but quad not responding, its my first racer, please guide.

I have a dji flame wheel. The flysky FS-i6 is missing so I need to program another one which I bought with the FS-i6 flysky reciever and bind it. How do I know if it's clean flight or Betaflight? What else do I need to know to get it to fly.

Have you messed with your Raptor 390 lately? You been able to get your LED pinouts to work on that FC?

Definitely helping me. But Km still lost. Lol Thanks

Hi got one problem . for some reason my little one pulled out all my cables out of my machine i6 what colors goes where ...

why is it when I try to configure my Eachine i6 remote controller in Libre Pilot, when I check to see if the remote is responding correctly with the on screen controls for throttle, pitch , roll and yaw, they do not move in the right direction on the screen that they should be moving {when I move throttle up the on screen controls show that the throttle being moved downward instead of upward. How can I fix this problem. Thanks

Can u show programming for a drone

where to do it under number 4

One more thing I brought the transmitter separate not rtf they told me I had to buy the other receiver fs ia6b

will this flysky work with a ar 2.0 drone

i got a question, where are the red,black and white cables attached to from the quad copter @ 5:13 ? Thank you!

My transmitter is not responding like yours is when you go to betaflight I check if all the channels were in the right place but I checked all the channels same as yours but I don't know what I'm doing wrong

thanks great tutorial really appreciate

Can I get a tricopter setup for the fsi6?

there us no movement on mine too. Its not letting me change uart 1 to serial rx but i was able to change uart 2 to serial rx. I do have it on serial based receiver and ibus.

Great video, very helpful

I connect mine and nothing pops up in my lab top

As a beginner, which flysky model would you advise? So many different models of flysky receivers. I'm making wood planes and gliders.

quick question why should multi rotors be setup on plane or glider? i set mine up on fixed pitch heli am i doing something wrong?

Hey bro, you still got that Walkera Rodeo 150 ? You said you were selling it for around 80, I was wondering if you would do 75, ? I was able to scrape together atlesst that much!!?

Hey man thank you for this. I have my eachine I6 bound to the ppm ia6b RX and ppm set in betaflight but for some reason my channels aren't moving like when you go to set your endpoints in receiver in betaflight. I just had the pwm version working on the same quad a day ago and then I get the ppm version and it's not working. You think it's a bad RX? There were some bad reviews I read on Amazon where I got it. I hope I'm just doing something wrong. Hope you can help thank you.

Hi, I'm a super boob, but I wanted to know, if I'm suposted to leafe the resever in the Drone or, If I should unplug IT again, when everything is set up 😁(or in other words should I fly with the resever?)

Can i use this transmitter with wakera 250 racer and vortex 285 drones.

We don't need laptop for uploading software?

I’m a little confused. I followed Another build tutorial and he didn’t do this. I don’t have power for the receiver to bind it. How do I power it?