Flysky FSI6X Open Tx Firmware Installation via DFU Mode
Рет қаралды 19,223
Күн бұрын#Flysky #FSI6X #OpenTX
In this video we take a look at how to install Open Tx firmware on the Flysky FSI6X Radio transmitter via the DFU mode so that you can avoid using the st link usb programmer.
00:00 Intro
01:11 Bridge R53 Pad
03:10 Solder R53 Pad
03:51 Test DFU Mode
04:40 STM32 Cube Programmer
06:20 Connect Radio To Pc
07:40 Backup Original Firmware
08:15 Installing Open Tx
08:49 Remove R53 Bridge
09:15 Test New Firmware
10:01 Open Tx DFU Mode
10:49 End
STM 32 Cube Programmer - www.st.com/en/development-too...
Open TX FSI6X - www.rcgroups.com/forums/showt...
Er9x FSI6 FSI6X - www.rcgroups.com/forums/showt...
Thanks for watching!
@islandrc-duke1972 2 жыл бұрын
great information on the firmware
@RakishRc 2 жыл бұрын
Thanks as always! 👍
@Sunnyfpv1617 Жыл бұрын
A lot helpful 👍❤️
@suradesjunda 2 жыл бұрын
ขอบคุณครับ
@polypusify 2 жыл бұрын
You dont have to solder wires to the R53 pads, I've used a pair of tweezers like the ones you use to point to the pads and it worked like a charm. You only need the pads bridge the moment you power on the radio, you cand remove the bridge after and the radio will stay in DFU mode
@RakishRc 2 жыл бұрын
Yes I can understand. But it takes multiple attempts to get it working with a tweezer. I find the wires much better but if anyone wants to try the tweezer way they can 👍
@mstram Жыл бұрын
Flysky sure isn't making it easy to to go to DFU mode are they?
@peteryoussef8263 2 жыл бұрын
Great :)
@RakishRc 2 жыл бұрын
Thanks 👍
@user-bz6bq1yj6p Ай бұрын
UPDATE: I'm upgrading from original FW to Openi6x v1.11.1 by following this tutorial BUT the TX seems like it is bricked and does not display anything. If you have the same issue, you can try to do full ERASE using STM32 Cube Programmer and then try to re-flash following this tutorial. I realize that the output log in this video did show "ERASING SECTOR ..." which I suddenly thought that why his step does involve erasing sector when by default, STM32 Cube Programmer will not erase the chip and may show "Sector not found".
@thomasbeauchamp9801 Жыл бұрын
Hi Rakish, I am interested in your method to install opentx on flysky radio because I would like to use a headtracker with mine. As I saw in your video dedicated to the use of headtrackers, I have to install open tx on my flysky. However, I have an fs-i6. I saw in one of the comments below that there is another firmware for fs-i6 but is it opentx too? And will I be able to use an headtracker with this other firmware? Or should I rather buy an fs-i6X? Thanks
@actomaz Жыл бұрын
Hello @Rakish Rc I'm trying to put the radio in DFU mode but windows recognizes the usb as a malfunctioning device, can anyone help?
@leivinreec.dolenzo1099 4 ай бұрын
thank you for this informative viode my friend just flash on the 1.4.0 version on my transmitter. I just notice that the higher version you download it wont work due to increase of memory usage of the new update file so my transmitter work or only accept the 1.4.0 version.
@jimcrane2529 Жыл бұрын
So I updated to Ver1.6..0 using STLink V2 & four wires - worked Great - rebooted Transmitter and noticed wrong language selected - powered Transmitter off and installed serial cable & pushed both horizontal trims to center to set to DFU mode - now unable to reprogram using STMCubeProggramer (no connection to usb - windows sees device as DRPm32DFUISPMODE (NO DRIVER) & NO COM. - ANY SUGGESTIONS ?
@luisfilipe1983 2 жыл бұрын
Great option, but once again i have to ask..will it work the same for the i6 radio? Just jumping the r53 pads?? Maybe not...considering that the main board is different🤔
@RakishRc 2 жыл бұрын
Hi, no this won't be same for i6 because the board is different. There might be a pad to jump but not sure which and of it'll work.
@Kartik5t Жыл бұрын
I had do same..but now my fsi6x is garbage for me. After installing opentx.every time when I on the switch.shows switch warning ABCD & throttel warning..then when i fix it all switch and throttle position.its hanged after last action.then restart with fix all switch and throttle.only show White screen..also instal old firmware but tx not responding still in dfu mode like.please help
@r.g.lakshansadaruwan3193 2 жыл бұрын
Can you make a video flashing the original flysky firmware to the flysky f6X transmitter?
@MarkusPeikert 9 ай бұрын
thank you for your good structured video. unfortunately i now have the problem that my chip is read protected. do you think it will be better when i buy st-link?
@RakishRc 9 ай бұрын
Yes because you can then disable the read out protection which is at level 1. Remember the existing firmware will be lost once read out protection is disabled.. however the original firmware file for fsi6x is easily available so not to worry. Then you can flash the openi6x firmware and enjoy
@readlee Жыл бұрын
If you do not want to solder the R53 pins and you have standard FS-i6X firmware, you can enter DFU mode via the following process. Power off the radio, push and hold the left vertical trim to the right and the horizontal trim down.. While holding them, power on the radio. The LCD will stay blank and you are in DFU mode. That said, whether I enter DFU mode via this the trims or by soldering the pins, my radio isn't read as any STM32 device, it is still read as a flysky radio controller?? I'm going to try the ST-Link v2 adaptor instead.
@RakishRc Жыл бұрын
Hi, you're right about the dfu mode initiation on stock firmware however the dfu mode is different with original flysky firmware and cannot be detected as a stm dfu device to completely erase and flash a new firmware. That's why the r53 pins are suggested for the stm processor dfu mode. If radio is correctly setup in dfu mode and unable to detect or show on computer then check the usb cable and usb port on computer along with stm dfu drivers if not installed. ST link usb device is also a sure shot way but need extra soldering which is not worth...r53 is the easy way with a pair of tweezers for the very first flash.
@lokaero Жыл бұрын
Hi rakish. im having a problem here. when i was updating unfortunately my usb disconnected. now my tx is dead. not turning on can u give me soultion?
@sirhcw4369 Ай бұрын
In device manager its labeled as other devices- AMP32 DFU ISP Mode. What is wrong and what do i do to fix it
@sarasu5614 2 жыл бұрын
Hi rakesh bro. Did we can flash from i6x firmware directly to openi6x 1.3 with this method ?
@RakishRc 2 жыл бұрын
Yes you can. Just make sure you initiate the DFU mode properly and then flash the latest open tx firmware file 👍
@GKCcisco 2 жыл бұрын
Legendary
@RakishRc 2 жыл бұрын
👍
@GKCcisco 2 жыл бұрын
@@RakishRc I am stuck at the device manager, my device is called APM32 DFU ISP mode, what did i miss? im running windows 10 thanks
@GKCcisco 2 жыл бұрын
Also this was a new i6x that just arrived with stock firmware.
@RakishRc 2 жыл бұрын
@@GKCcisco so your radio does seem to be detected in dfu mode. Did you try flashing firmware from STM 32 cube programmer?
@RakishRc 2 жыл бұрын
@@GKCcisco what's the date on your fsi6x motherboard?
@TheDzejpiem Ай бұрын
Helping Hello, is there any other place to connect to the broken left pin in the R53 jumper?
@TheDzejpiem Ай бұрын
Solved L pin from R52
@ruanvandermerwe9982 2 жыл бұрын
I followed your steps exactly and everything seems to work, however when I press "download" the STM32 program just loads and loads. I have tried previous versions of the Openi6X but all just keeps loading....Any suggestions?
@RakishRc 2 жыл бұрын
Do you see the radio in device manager as STM 32 dfu device? If yes make sure to select usb option in top right corner of STM 32 program and then connect. Select the firmware file and then click on download.
@mohammedakakeza 11 ай бұрын
can i do this on i6s ?? plz tell me
@zio_cuy 2 жыл бұрын
Its a great info, but i have a question before i installed open tx firmware, 1. Is protocol stil afhds and afhds2? 2.Can we change the power output 3, is there a timer in it? 4. Can we back using flysky original firmware? Thx a lot...
@RakishRc 2 жыл бұрын
Protocol Is afhds2a, power output for elrs is adjustable not for regular built-in module because it anyways doesn't support that, yes you can setup timers, yes you can revert back to original firmware if needed. Thanks for watching 👍
@zio_cuy 2 жыл бұрын
@@RakishRc you are so helpfull, thx a lot.
@r.g.lakshansadaruwan3193 2 жыл бұрын
Can you tell me how to put the backup original firmware back into the flysky transmitter??
@RakishRc 2 жыл бұрын
Same process just while flashing use the original firmware file. Use either dfu method or st link method make sure to use right file
@aadharsh1094 Жыл бұрын
How do i setup this with a sim?
@onelinkrecords 4 ай бұрын
My 6x only comes up as apm32 isp dfu mode not as stm32 boot loader is there’s way to flash these one it does not show up in the software
@onelinkrecords 3 ай бұрын
It not worth it sir you have to use the stlink but it not worth it
@richardsmithson4227 2 жыл бұрын
where can i get factory firmware for the fsi6x.. might not have saved mine.. also, reason i need it is becasue when i go to expresslrs in the menu for open tx it just says Loading????. i dont know why. and ive flashed multiple times. 1.3version
@RakishRc 2 жыл бұрын
The loading message means either some mistake in wiring the elrs module to the radio, if you haven't enabled crossfire protocol in external module settings in model settings, or you don't have elrs 2.0 on your tx module. Check if the ground and tx2 signal wire is soldered properly to the radio and connect correctly to the module
@Mike4_friends 2 жыл бұрын
If you have stored Models in Transmitter - do they stay or you have to re-program them?
@Mike4_friends 2 жыл бұрын
To be more clear: I mean if you upgrade 1st time - from original software in Transmitter to Open TX ?
@RakishRc 2 жыл бұрын
@@Mike4_friends For the first time from. Factory firmware to Open Tx firmware all models will be lost as the eeprom is different and reset. Once you install latest open tx firmware you can always back up your new models eeprom file. But at the moment restoring models from different open tx firmware is not supported fully.
@Mike4_friends 2 жыл бұрын
@@RakishRc After bridging - connecting to USB and STM32 Cube Programmer I get the Warning "Device is under read protection! If you want to disable RDP please reconnect with Read Unprotect enabled." If I mark read protect block - still can not enter USB programming mode ??
@Mike4_friends 2 жыл бұрын
Solved - thanks
@MyNameSani 2 жыл бұрын
Hi, I did everything according to the instructions, but when connected to the computer, no USB devices appear at all. In my case, only ST-LINK will help? Maybe you have faced such a problem? - Windows 11
@GKCcisco 2 жыл бұрын
Did you have any luck? I have a similar issue
@Rooonga 2 жыл бұрын
@@GKCcisco I have the same issue, but I think it might be because of the datacable. I'm trying to use the one for the game on PC, it's the type that has an audio connecter in it. I think it might not actually be transmitting data. Have ordered a data cable to see if it helps. @rRakish Rc can you please confirm?
@anandanmunusamy2716 Жыл бұрын
I am also having same issue. Cube programmer showing:no dfu mode
@mikel0520991 Жыл бұрын
@@anandanmunusamy2716 same here, done it before but wont work now. no dfu mode. Ever figure it out?
@ManiAoulkh 8 ай бұрын
Anybody figured out???
@Rooonga 2 жыл бұрын
Windows isn't seeing my controller. I'm using a cable that has a kind of audio jack in it. Is this the wrong lead? I'm hoping it's an easy fix with a new USB data cable. Any advice would be great thank you
@RakishRc 2 жыл бұрын
You can build a diy usb cable. The pin out for the rear connection port is available on KZfaq and goggle. Find any usb cable and cut the small connector end and match the wires to rx tx gnd and VCC connection.
@Rooonga 2 жыл бұрын
@@RakishRc I did! Worked an absolute treat and actually worked I like the 2 usb leads I’ve bought. Thank you!
@RakishRc 2 жыл бұрын
@@Rooonga Enjoy! 👍
@theinventionshow 2 жыл бұрын
when i hit the download button to update to opentx the STM32CubeProgrammer just closes any help?
@theinventionshow 2 жыл бұрын
All the reed and backup prosses gose smooth and the load of the new firmware but when i press the download button the programmer just closes
@theinventionshow 2 жыл бұрын
Ok i try it on a difrend pc and worked fine thanks for the video
@swift4856 2 жыл бұрын
Hi Well Done. Will this work with my Turnigy / Flysky i6S touch screen model? Thanks
@RakishRc 2 жыл бұрын
No I don't think it will work. You'll brick your radio.
@swift4856 2 жыл бұрын
@@RakishRc Yes thanks for warning. I found out apparently there is no implementation for the touch screen to work with OpenTx so wouldn't work
@aadharsh1094 Жыл бұрын
also bro i need the 2019 sep firmware file can u send me that??
@messourav5141 2 жыл бұрын
Hey, for me when I click connect it is giving error that read out protection is enabled. please help...
@RakishRc 2 жыл бұрын
Hi, at top left you'll see OB / option bytes. Connect your radio in dfu mode and see if you get disable read out protection option under OB settings
@mujudon9527 2 жыл бұрын
@@RakishRc no....same issue still
@srinivasreddypamulapati5608 2 жыл бұрын
I have faced a issue with my windows 11 laptop...when I tried to connect the transmitter in dfu mode to stm32cubeprogrammer I got an error showing device is in read protected mode...and I couldn't find any solution for it....but when I connected in my windows 10 laptop everything worked fine
@RakishRc 2 жыл бұрын
In stm32 cube programmer on top left corner there's settings option through which read out protection should be disabled. But you've got it working i guess by now 👍
@srinivasreddypamulapati5608 2 жыл бұрын
@@RakishRc yaa i have got it working but in my windows 11 i couldn't even get it connected in the software to change any settings....by the way thanks a lot for the information your videos help a lot🤗...keep doing these videos
@RakishRc 2 жыл бұрын
@@srinivasreddypamulapati5608 glad you have it working 👍 thanks for watching!
@rccowboys 2 жыл бұрын
@@srinivasreddypamulapati5608 Yep... This doesn't work with win 11. smh... Why did I upgrade?. lol...
@carpediemonline360 Жыл бұрын
How do I return to stock fw if I dont have a backup?
@RakishRc Жыл бұрын
You can download original firmware from Google/ cleric GitHub repository. Just use stock firmware file and update like shown with open tx firmware file
@illusionistsam 2 жыл бұрын
Bro can you send me original file
@jacquesadendorff1175 2 жыл бұрын
if you flash Open TX to the FS-I6x transmitter, Can you bind any receivers to it OR only Flysky receiver?
@RakishRc 2 жыл бұрын
Flysky receivers, express lrs and tbs crossfire are supported and any tx and rx ppm module as well 👍
@jacquesadendorff1175 2 жыл бұрын
@@RakishRc can you bind Frsky receivers also
@RakishRc 2 жыл бұрын
@@jacquesadendorff1175 no
@jacquesadendorff1175 2 жыл бұрын
@@RakishRc thanx man, is it worth changing over to openTX. i just started with FPV drone
@RakishRc 2 жыл бұрын
@@jacquesadendorff1175 open tx is a huge upgrade for fsi6x. I am myself new to fpv drones as well.
@actomaz Жыл бұрын
@Rakish Rc I'm trying to put the radio in DFU mode but windows recognizes the usb as a malfunctioning device, can anyone help?
@RakishRc Жыл бұрын
Hi, did you check which processor is on your fsi6x? If it's stm32 then you'll need to install stm32 drivers. If it's geehy apm32 processor then let me know I'll share more links on how to get it flashed with open tx firmware. Did you install stm32 cube programmer? Sometimes switching to a different usb port might help.. check if usb cable is good
@actomaz Жыл бұрын
@@RakishRc Hello, I checked that my FS-I6X's processor is a geehy apm32, I installed STM32 drivers and tried all USB ports, but the error is the same. Can you help me?
@RakishRc Жыл бұрын
@@actomaz github.com/OpenI6X/opentx/wiki www.rcgroups.com/forums/showthread.php?3916435-FlySky-I6X-port-of-OpenTX/page16 Check these links..you need to use qmk toolbox to flash firmware for gheey processor
@actomaz Жыл бұрын
@@RakishRc Thanks!! It worked... I was able to install opentx!!!! Thank you!!
@RakishRc Жыл бұрын
@@actomaz awesome! 👍
@aadharsh1094 Жыл бұрын
Does the flysky recievers still work with opentx?
@RakishRc Жыл бұрын
Yes flysky AFHDS2A receivers work 👍
@aadharsh1094 Жыл бұрын
Can I get the jst connector pinout?
@RakishRc Жыл бұрын
For the debug port? Need to check it's mentioned on rcgroup forum page i think
@jonujangid3J 2 жыл бұрын
Can it work on fsi6 & frsky receiver bind it with fsi6
@RakishRc 2 жыл бұрын
For fsi6 there is erfly6 firmware with crossfire support. Don't think you can bind Frsky receiver because no multiprotocol
@-never-gonna-give-you-up- 2 жыл бұрын
How do I bind?
@RakishRc 2 жыл бұрын
In model settings under protocol option there is bind option. Put the receiver in bind mode first and then turn on radio and select the bind option to bind the receiver 👍
@corneliudoc 2 жыл бұрын
Hi! How to roll back to backed up flysky firmware?..
@RakishRc 2 жыл бұрын
Same process just select original firmware file and click download.
@corneliudoc Жыл бұрын
@@RakishRc same addresses to x20000?..
@aravindwilson1558 2 жыл бұрын
Sir pls do the same video with fs i6 tx also.most off them are using fs i6 instead of fs i6 x
@RakishRc 2 жыл бұрын
I don't have fsi6 unfortunately and open tx is not supported on fsi6 only works on FSi6X. For fsi6 er9x aka erfly6 is the best firmware. 👍
@aravindwilson1558 2 жыл бұрын
@@RakishRc so please flash er9x on fs i6 using method shown on the video 🙏🙏🙏
@royalamv8206 2 жыл бұрын
Can I still bind with flysky receiver?
@RakishRc 2 жыл бұрын
Yes! 👍
@illusionistsam 2 жыл бұрын
My buttons dont work and radio gets stuck on switch warning still no luck
@RakishRc 2 жыл бұрын
Hi, it seems like your radio is damaged. I'll send you the original file try that.
@Kartik5t Жыл бұрын
Same issue also with me..
@illusionistsam Жыл бұрын
@@Kartik5t bro mcu is fried i had to change the mcu
@goobisoft4873 2 жыл бұрын
Will this firmware gives u better range
@RakishRc 2 жыл бұрын
Better range with stock flysky receivers? I don't think firmware would make a difference on the range for flysky receivers. But express lrs is exactly for that...long range and strong signal connectivity 👍
@bachansahiljewellers 2 жыл бұрын
Brother my radio can't connect with my pc and i install all stm drivers which is use to connect what is will do now and one more thing i change my mcu chip with new one how upload firmware on it the chip is fully blank I change because older one was burned because of high voltage plz reply I wait for your reply
@RakishRc 2 жыл бұрын
Hi, when you connect in dfu mode does it show up in device manager? The MCU you replaced is exactly the same as before right? If you are following dfu method then make sure r53 pad is bridged as shown from this video or solder the St link pads and use a St link V2 usb adapter. Either ways you should be able to flash the firmware and get the radio working 👍
@bachansahiljewellers 2 жыл бұрын
@@RakishRc no it can't show in device manager
@bachansahiljewellers 2 жыл бұрын
@@RakishRc and the mcu is same
@RakishRc 2 жыл бұрын
@@bachansahiljewellers did you also replace the power regulator and other components that might have been damaged?
@bachansahiljewellers 2 жыл бұрын
@@RakishRc only mcu burn
@anandanmunusamy2716 Жыл бұрын
Cube programmer is showing:no dfu mode. I have done everything as in your KZfaq video
@RakishRc Жыл бұрын
Radio is not connected to computer correctly. Check usb cable is good and in device manager if raido shows up after connection and what it's displaying the device as
@onelinkrecords 4 ай бұрын
He’s right it shows up in device manager as apm32 not stm32 so it don’t come up in the program
@almacfpv74 2 жыл бұрын
Hey. I did the opentx firmware upgrade by watching your video. Thanks and big help but I can't get my crossfire module to work. Can you help?
@RakishRc 2 жыл бұрын
Did you wire the tx2 pad for signal wire with a ground pad? And then have you selected crossfire in the external protocol settings? It should work 👍
@almacfpv74 2 жыл бұрын
@@RakishRc yes did all of that twice. I'm getting nothing
@almacfpv74 2 жыл бұрын
@@RakishRc also. How do I apply the elrs lua from the tools. When I click on it it just says loading
@RakishRc 2 жыл бұрын
@@almacfpv74 if it's stuck on loading that means the elrs module and radio are not communicating properly. Check if the wiring is correct and elrs 2.0 firmware is flashed on rx and tx module
@RakishRc 2 жыл бұрын
@@almacfpv74 I've got a video on elrs 2.0 menu for this radio coming soon 👍
@Mike4_friends 2 жыл бұрын
STM32Cube connected to USB - Error: 09:19:30 : Manuf. ID : STMicroelectronics 09:19:30 : Product ID : STM32 BOOTLOADER 09:19:30 : SN : FFFFFFFEFFFF 09:19:30 : FW version : 0x011a 09:19:30 : Board : -- 09:19:30 : Device ID : unknown 09:19:30 : Warning: Device is under Read Out Protection 09:19:30 : Disconnected from device.
@mujudon9527 2 жыл бұрын
same issue for me also
@meltonermeltoner Жыл бұрын
can't i use the regular firmware updating tool (flysky-updater-win64.exe) and select openi6x_1.6.1_en.bin for example to update the firmware? it said Unexpected firmare size: 128168 bytes. Use --force to flash anyway. so i canceled it and preferred to ask before trying it. thank you for your help
@RakishRc Жыл бұрын
It's possible can you send me that flysky updater tool. I had it once but it's not available on flysky website anymore. It could work but will have to test. Even something goes wrong you can always flash original or open tx firmware by dfu method. No harm in trying.
@sirhcw4369 Ай бұрын
Will this work on the i6
@RakishRc Ай бұрын
I6 has erfly6 firmware..it has similar features check erfly6 firmware for i6 you'll find all information
RCwithAdam
Рет қаралды 73 М.
Drone Mesh
Рет қаралды 60 М.
ALNADO
Рет қаралды 26 М.
RCwithAdam
Рет қаралды 39 М.
Rakish Rc
Рет қаралды 8 М.
Drone Mesh
Рет қаралды 47 М.