This video shows how to replace the input shaft seals on the dual clutch automatic / DPS6 / Powershift transmission. Here is a video of transmission removal for a ford focus: • Ford Focus Clutch & Fo...
Пікірлер: 34
@StephenLowe-y6d8 күн бұрын
2 questions: (1) My clutch kit didn't have grease for the forks. What type grease is best for this?; (2) should I grease the input shaft to make seals easier to install or not - what grease would be best if I should? Great set of videos !!!!!!!
@BigBensCarsAndCycles8 күн бұрын
@StephenLowe-y6d I'd use some moly grease and no, I wouldn't put too much on the shaft.
@zaza6151 Жыл бұрын
Great video. I don't get how you don't have more subscribers. Specailly people like me who own focus.
@BigBensCarsAndCycles Жыл бұрын
Thank you for watching! I'm still pretty new on KZfaq. I've been doing videos regularly for only a few months. I'm trying though! I'm running ads on facebook for the channel lol. Thanks again for watching.
@DetroitMicroSound Жыл бұрын
He'll get there...Wait until he starts doing things like a TCM tune....... 😁
@jeffgammon1392 Жыл бұрын
Great videos. Thanks for he help for the DIY guy
@brave0nej4 ай бұрын
little seal comes out pretty easy with a m12 surge on 2
@gcposeidon080010 ай бұрын
Thank you!!!
@BigBensCarsAndCycles10 ай бұрын
You're welcome!
@rogerboguski13553 ай бұрын
Watching your other videos to work on this 2014 focus DCT .. also have a 2015 I'm doing after this one. Ever run into the tool not pulling the input shaft seal? So freaking frustrated. screwing down the tool just spins the shaft now and I can't get it to sit and pull out. Any advice? picks don't seem to be able to get under and pull it loose.
@BigBensCarsAndCycles3 ай бұрын
Sorry to hear. I've had to grind down the end of the seal extractor before in this situation (removing part of the smaller end) which allows the tool to bite in right away
@rogerboguski13553 ай бұрын
@@BigBensCarsAndCycles I got it. Had to walk away from it for a couple of hours to clear my head :) I took a small straight pick and tapped it between the wall and seal and caused a small indent in towards the spine. That allowed the tool to get a better bite and it pulled out. The inner part was a pain but I ground down two small right angle picks so it would fit and managed to work it out. On to the next curse inducing problem.
@rogeliosalcedo85853 ай бұрын
Hi... What did you use to clean transmission before to change seals? This in minute 2:00... Thank you...
@BigBensCarsAndCycles3 ай бұрын
Hi, I used brake parts cleaner. Thanks for watching
@user-bf6nn9po2dАй бұрын
Would this apply for my 2007 ford fusion?
@BigBensCarsAndCyclesАй бұрын
No, those had different transmissions
@zoticoreyes1166 Жыл бұрын
Hi Ben where can I buy the seals? What are the exact names? Thanks in advance! Your video thus far was the best for this job! I’m almost done n will end up saving over $3K !
@BigBensCarsAndCycles Жыл бұрын
Awesome. Glad to help. The seal kit is EV6Z-7052-C
@BigBensCarsAndCycles Жыл бұрын
Also they're at the ford dealer parts department
@zoticoreyes1166 Жыл бұрын
Ty sooo much
@elijahsandlin94615 ай бұрын
Hello Ben I have a 2018 ford focus that had a sheard case lug. After replacing the case I am getting a 1st and 3rd non engagement do you have any ideas.
@BigBensCarsAndCycles5 ай бұрын
Any codes
@Sons_Of_Liberty_1739Ай бұрын
What are the part numbers for said seals?
@BigBensCarsAndCyclesАй бұрын
@@Sons_Of_Liberty_1739 amzn.to/3UHEAe9
@Sons_Of_Liberty_1739Ай бұрын
@@BigBensCarsAndCycles Thank you! Getting ready to do my sons 2014 focus. Lost reverse , so I popped out actuator b and I realized the shift fork is toast and lost its recoil. So a Luk clutch kit it is. I appreciate your help and videos.
@davidjones40615 ай бұрын
Huge issue. I took out my newly installed clutch and forks ect… to do the Input shaft seals. When I put the new seals in and the clutch back in the clutch won’t sit fully now and I can’t get the first snap ring on. Do you know the issue?
@BigBensCarsAndCycles5 ай бұрын
The clutch needs to be reset before insertion kzfaq.info/get/bejne/rqeqhJZkuMWlc3U.html
@davidjones40615 ай бұрын
Even if I never put the transmission back in my car?
@BigBensCarsAndCycles5 ай бұрын
@@davidjones4061 correct. If you unlocked the clutch it must be re locked
@davidjones40615 ай бұрын
Thank you! You have been a great help. Everyone looking to fix their cars I recommend his videos! Only thing is I hope I didn’t damage the shaft from hitting it hard with a hammer (was my fault)
@michaeladams73029 ай бұрын
Do you have a link to the seal remover/installer tools?
@BigBensCarsAndCycles9 ай бұрын
Here's an aftermarket kit on amazon a.co/d/7jxRJRL