FULL Lanoguard RUST TREATMENT on a Land Rover Discovery!🚘✔
Рет қаралды 37,376
Here's the 8000+ strong Lanoguard Users Group Facebook Page - come and say hello: / lanoguardusers 👀
This video shows a full Lanoguard rust treatment on Mark's Land Rover Discovery. It will show you how to get the most from Lanoguard and will focus on vehicle prep, the Moto Grease, the Lanoguard spayers, the DIY kit and the Injector Wand. Although we were lucky enough to have access to CR Allen's workshop, treatments can be easily applied at home using regular ramps.
To find out more or to order your Lanoguard Underbody Rust Treatment click here: www.lanoguard.co.uk/
We provide simple, easy, DIY care for your vehicle underbody (you don't need a ramp!) that you can apply all year round, even in cold, damp conditions. Protecting the underbody of your vehicle is often neglected, expected to be messy, needing tools you don’t have, and a smelly, difficult and time-consuming job.
With our kits, this all changes and is made easy for you. Lanoguard underbody rust protection is long-lasting and can be applied in around 20 minutes and will defend the vehicle you love from corrosion so you can enjoy using it without worry. 👍
=================================================
SUBSCRIBE TO OUR KZfaq CHANNEL NOW! / lanoguard
SOCIALS:
Facebook: / lanoguard
Twitter: / lanoguard
Insta: @lanoguard
TikTok: @lanoguarduk
=================================================
Timecodes
0:00 - Intro by Mark
0:30 - Prep and jet wash
0:54 - Checking and preparing the underbody
3:49 - Applying the Lanoguard Moto Grease
6:23 - Using the Lanoguard Pro Sprayer
7:14 - Using the Lanoguard DIY Underbody Care Kit
9:52 - Unsing the Lanoguard Injector Wand
10:59 - Conclusion
#rust #rustprotection #rusttreatment #underbody
@curtis8516 2 жыл бұрын
Did my Aygo with it on the drive with a plastic sheet under it. The car was so narrow it didn't need jacking. Very therapeutic and knowing it won't rust. Highly recommend Lanoguard to anyone who gives a toss about their car.
@Lanoguard 2 жыл бұрын
Thanks Curtis - that's great to hear.
@martinward7966 25 күн бұрын
Fantastic video thanks for your time to demonstrate looking to do my mitshubusi l200 be definitely be buying lanoguard thank you.
@Lanoguard 22 күн бұрын
Thanks for your comment, its appreciated, please do let us know if you have any further questions or queries on how it may perform for you, be sure to ask. We're always here to help! Thanks.
@henryburrows5934 2 жыл бұрын
Excellent video! My kit arrived last week for my Discovery 4 and have just given it a good coating :) I now feel like a Lanoguard salesman with my friends and family singing your praises and handing out the leaflets you added to my pack 😅
@Lanoguard 2 жыл бұрын
Ahhh. Thank you so much Henry. That’s really cool. Appreciate the sharing of it. Thanks. Mark
@TheSpragz Жыл бұрын
Done my new GR Yaris lately. Good peace of mind with winter approaching. Just wish they’d ban the use of rock salt full stop.
@Steve-wz5lx 2 жыл бұрын
Received my 2x2ltr & grease & trigger gun. ⭐⭐⭐⭐⭐ & 10/10. I coated underside of 2012 qashqai, ( notorious for surface rust ), looks amazing , I did the springs, sills and wheel arch liners ( plastic ) for a continuos look . I'm confidant with using the product, it cleans up a treat with regular detergent. Most important though, it's transformed the vehicles appearance & will now help preserve it , ready for the mot inspection in a few months. Used less than 750 ml, so many more applications in hand for the future..
@Lanoguard 2 жыл бұрын
Hi Steve, really glad you like the product and happy with the appearance after applying, please do share some photos and if not already please join our Facebook User Group - facebook.com/groups/lanoguardusers
@dazzler011 2 жыл бұрын
Excellent video, bought my first kit last week for my very crusty MX-5 NC, got a week off so that's the job of choice....
@matthewellis9885 10 ай бұрын
Hope you fixed the rust first before just undersealing over it.. that'll be an expensive mistake come MOT time
@aswinps93 8 ай бұрын
Any tips on doing this procedure on an nc mx5? Looking to do it in my 09 mx5 as well. Did you use a wiremesh to remove the existing surface rust before spraying it on? Or will just a pressure wash on the underbody to remove the dirt suffice?
@dazzler011 8 ай бұрын
Hi,Yes I did,went a bit belt and braces tbh,wire brush on a drill and cleaned all accessible areas, MOT was a few months later and he said I'd done a fine job,good tip for the MOTO Grease is to keep it in a bucket of warm water,you can just paint it on all vulnerable area's...
@BianShaw 2 жыл бұрын
Plan of doing my 2 year old Hyundai Tucson in Lanoguard its previous owner had a towbar and it had a bit of a hard life but nothing a bit of time and love can't fix. Would love to be able to rent a ramp for the day and make sure it's done 100% exactly like you did in this video.
@shaunjones7234 2 жыл бұрын
Looking forward to see the longevity of it, as I’m interested in purchasing it. 👍
@warrendudley5616 2 жыл бұрын
Cheers Shaun - check this one out - kzfaq.info/get/bejne/d9pihquJvK_SYJs.html
@Beemer760 9 ай бұрын
Great video on how to spray , what about evidencing what exactly it does other than make things look shiny !
@Lanoguard 9 ай бұрын
Hi, There is a follow up to this video showing how Lanoguard has held up 1 year later and Mark the owner topping up his treatment 1 year on. Here is a link to the video if you are interested - kzfaq.info/get/bejne/eZh8eciimK6zl3U.html Please have a look at our user group which has over 15,000 members who have tried and tested Lanoguard and are always happy to share their experiences and answer any questions. - facebook.com/groups/lanoguardusers I hope you find the above of interest and if you have any questions or would like more information please do contact us, we are here to help
@mauricebarnett6951 Жыл бұрын
Can vouch this is a brilliant product and trust me ive tried them all over the years, and nothing beats Lanoguard. Ive put it on my Discovery 2 and its easy to apply no compressor needed
@Lanoguard Жыл бұрын
Hi Maurice, thank you, we really appreciate you taking the time to leave some feedback, glad your happy with the product :-)
@Landy_Bill_Ex_Mil 2 жыл бұрын
Great video! Im planning on treating my ex mod 110 to some protection as its nearly 30 years old! I also like the fact its so easy to apply and can be sprayed almost anywhere!
@Lanoguard 2 жыл бұрын
Hi, thanks for the comment, have you treated your Ex MOD Land Rover with Lanoguard? If so how did it go, please join our Facebook User Group and share photos we love to see customers Lanoguarded vehicles , here is a link to our user group facebook.com/groups/lanoguardusers
@JJamJ Жыл бұрын
Certainly helps to be able to raise the vehicle. Used my 1st Lanoguard application yesterday. Unfortunately I didn't have access to a garage but managed to raise with ramps. A great product and I will personally apply every 6 months. It Don't half smell though:)
@cblack1green Жыл бұрын
Just done my Discovery 4 today, it is a lot better to use than the black spray types I have used In the past, I did mine by using car ramps with the suspension in off road mode to give me as much clearance under there as possible, have to say though I would of loved to have access to a car ramp like you.
@Lanoguard Жыл бұрын
Hi, Great to hear your pleased with your Lanoguard treatment and really appreciate you taking the time to leave a comment. 😊
@paulandrews3785 Жыл бұрын
looks like a great product did my car when new its 27 years ago with gold wax but is in top condition bit wont to youes this product thanks for the video!!!!
@Lanoguard Жыл бұрын
Thank for the comment :-)
@pk-si6hq 2 жыл бұрын
Does this affect belts and brakes I watch a video where the guy covered the brakes and belts in the engine bay really good and informative video 👍👍👍
@shanthans4775 Жыл бұрын
It's a good question but no one responded
@bonesxcviii Жыл бұрын
Don’t spray it on belts, brakes or discs! It will really badly affect your braking
@Silentaudits7 2 жыл бұрын
Whoah ! soon as you said Peacehaven my ears went up ! I have a disco 2 that has surface rust under but nothing too bad. I really want to keep it and am willing to get the chassis TLC'd . I am Hastings area so you are a very possible. I will watch the rest of the vid and look to a phone number. It looks good so how long before re-treating ?... minimal road salt winter suffering. I get that you cannot say a def time but is it a once a year job or does it last ? And I would need a renta-ramp/lift . Any info ?
@Lanoguard 2 жыл бұрын
Hi, sorry for the very delayed reply, we suggest a yearly treatment/top up, but it does depend on what you use your vehicle for, it is worth regularly checking a topping up any area prone to rust or may have been missed during the first treatment. Depending on the vehicle will depend if ramps are needed the product is designed as a DIY home/driveway treatment. Have a look at this video which is done with no ramps under an L200 - kzfaq.info/get/bejne/e5h5gNqLuJ6ppGQ.html hope this helps
@martinsylvester1823 2 жыл бұрын
Great video, just ordered my first batch, am doing a systematic detail and treatment on my old Mercedes with pictures for the official MB club site. Will send them over when it is all done. Just wondered have you ever considered doing a small sticker or similar, one that could have a date written on. Think it would be a good addition to a portfolio especially when the car or whatever it is, is sold. I would happily pay for such a thing.
@andymanandyman3369 2 жыл бұрын
Hi Martin, I’m a member of the MBC too and am picking up a 2003 C180k in two weeks and am planning to use Lanoguard on my car. I’m interested to know how you got on using it for your old Mercedes’ ?. If your happy to then get in touch. Regards Andrew
@khalilrazak6486 Жыл бұрын
That's a very good idea.
@stevepickering5866 2 жыл бұрын
Just ordered my kit Mark for my 20yr old Defender Wolf…hoping it’ll be a bit less messy than Waxoyl !
@Lanoguard 2 жыл бұрын
Hi Steve, how did the application go - hoping you did find easy and there was less mess. Please do share some photos and your experiences on our Facebook User group, here is the link facebook.com/groups/lanoguardusers
@IanSRutter Жыл бұрын
This was fascinating and a great job of showing how to use it. Maybe I missed it, but is the coating safe on the rubber bushes? One can't help but get spray on the rubber bushes. Again, brilliant job, and I'm sure it will add value to the vehicle when selling.
@Lanoguard Жыл бұрын
Hi, thanks for the comment and glad you found it of interest. Lanoguard is safe to use on rubbers, plastics, metals, electrics, and circuit boards without any issue. It is jet-wash resistant up to 3000psi, non-perishing, non-conductive up to 70,000 volts, non-flammable and heat resistant up to 450 degrees. Therefore, you can spray the complete underbody of your vehicle even the exhaust the only areas to avoid are the brake discs and pad and if going in the engine bay the fan belt. These areas do not need to be masked up some people choose to cover them up if the wheels are off. Or use a piece of cardboard to shield the spray areas when spraying near brakes. I hope this answers your question.
@IanSRutter Жыл бұрын
@@Lanoguard Brilliant answer! What service. Cheers.
@markoreilly4433 2 жыл бұрын
Treated my 16 year old Honda CR-V a week or so ago. Jet washed one day and spent the next scraping snd sanding off rust & flaky areas. I covered everywhere and really believe you need to take the wheels off to get a thorough job done - up into the wheel arches and covering the lot ( I did rear off axle stands, then the front) . Injected into sills and box sections . The CR-V is classed as an estate , so it’s a large vehicle. For this initial comprehensive treatment I used a full 4 litres of Lanoguard. I didn’t have much call for the grease or the bottle that came in my kit but the flexible trigger hose is fantastic, as is the injection lance. Do you need to wear a mask with it being none toxic? Thanks!
@departe5672 Жыл бұрын
Hi there!I will do my CR-V too this weekend,can you please tell me if you have sprayed the engine area too ,the exhaust system and behind the disk brakes?Have you taken the rust out and treated it or just sprayed on top of it?How is it now after all that time ?Is still ok?And did you really used 4 lifters???
@herobo123456 2 жыл бұрын
ACF50 does the same thing
@conradtaggart9959 2 жыл бұрын
What about vermin? The soya/ organic oil VW use now on their electrical cable coverings is enough to attract them and cause them to eat through the cables. Looks like this could represent and even easier bigger feast for mice, rats etc. ...
@bertiebasset1752 Жыл бұрын
I'm looking to spray the underneath and inner wheel arches of my GR Yaris, just wondering if any sensors or brake discs need covering to prevent the Lanoguard getting on them or doesn't it matter? Cheers.
@Lanoguard Жыл бұрын
Hi, Lanoguard is safe to apply to your vehicles whole underbody, but do avoid the brake discs and pads and if going in the engine bay the fan belt. Some people choose to cover them up if the wheels are off. Or use a piece of cardboard to shield the spray areas when spraying near brakes. Hope that helps.
@khalilrazak6486 Жыл бұрын
Do you need to take the skid plates off or is that not a good idea also can I respray the exhaust with very high temperature silver paint?
@Lanoguard Жыл бұрын
Hi Lanoguard works well on hot surfaces because it doesn't evaporate. Works well on stainless steel exhausts too. It will burn off on areas that reach over 450 degrees. Lanoguard can be applied on top of painted surfaces, as it hermetically seals to the surface it is applied to. Ensure the paint is cured/dried to its final state before applying Lanoguard. In regards to the skid plates it is personal preference and removing them can allow better access to areas of the chassis. Hope this answers your questions
@barryholbrook9390 Жыл бұрын
Is lanoguard just a protector or a rust converter? I wanted to paint and protect my car which has surface rust.
@Lanoguard Жыл бұрын
Hi Barry Lanoguard protects and prevents. Lanoguard won’t convert existing rust per se, it will completely stop its further development. It will creep and bind underneath surface rust and create a barrier by hermetically sealing to the metal underneath stopping oxygen and water getting in. A side benefit of the natural chemical process that occurs when it hermetically seals to the metal, is that it does over time push any existing oxidation off. Making your surface look better over time, not completely rust free looking, but a little less rusty and the surface colour overall darkened down in colour. Hope this helps answer your question.
@Oli-zb6jb 2 жыл бұрын
Might sound silly but don't have time to do my own ford ranger. Do you offer a service to do it?
@Lanoguard 2 жыл бұрын
Hi Oliver, we ourselves do not offer a service, but we have many trade partners who will apply it for you. Please have a look at this link to find an application centre near you - www.lanoguard.co.uk/pages/application-centres
@Nick-bp7jf Жыл бұрын
Hi. So as long as the brakes are masked off prior to application, the lanoguard can be applied to things like springs, shocks, rubber bushes, bellows and electrical wiring without issue? Thank you.
@Lanoguard Жыл бұрын
Hi, Thanks for the question. Lanoguard is safe to use on rubbers, plastics, metals, electrics, and circuit boards without any issue. It is jet-wash resistant up to 3000psi, non-perishing, non-conductive up to 70,000volts, non-flammable and heat resistant up to 450 degrees. Therefore you can spray the complete underbody of your vehicle even the exhaust the only areas to avoid are the brake discs and pad and if going in the engine bay the fan belt. They do not need to be masked up some people choose to cover them up if the wheels are off. Or use a piece of cardboard to shield the spray areas when spraying near brakes. I hope this answers your question.
@Nick-bp7jf Жыл бұрын
@@Lanoguard Hi. Thank you for the speedy response. Sounds a great product. I did some small areas under the bonnet with waxoyl clear. Was not impressed. One youtuber who used it likened it to lard, i have to agree. He spoke very highly of the Lanoguard. He sprayed his very nice Jeep with it. Am i better off waiting for the spring before i apply your product?
@Lanoguard Жыл бұрын
Hi, Lanoguard can be applied in cold conditions and indeed in winter. It is ideally applied to a fully dry and preferably warm surface. That said, it is quite happy to be applied in the cold. Additionally, it is ok to apply Lanoguard spray to a slightly damp surface too and will disperse the damp as it cures. Warming the product in a bucket of warm water helps with application especially in cold weather. See here our blog all about winter Lanoguard application - www.lanoguard.co.uk/blogs/news/apply-lanoguard-in-winter-it-s-totally-okay-to-do-so I hope this helps and please do let us know if you would like any more information or have any other questions. If you do go ahead and purchase Lanoguard please do let us know how you get on. Thanks, Jen
@Nick-bp7jf Жыл бұрын
@@Lanoguard Thank you for the link, some great information. I will keep you posted.
@donnysweekendvanlifetravel7854 2 жыл бұрын
How much would I need for a l322 rangerover hat do you get with the kit regards donny
@Lanoguard 2 жыл бұрын
Hi, sorry for the very delayed response - here is a link to our Ultimate Land Rover Underbody Care Kit which will give you plenty to protected your vehicle and probably leave you with some left over for future top ups - www.lanoguard.co.uk/collections/all-our-great-value-kits-in-one-place/products/ultimate-land-rover-underbody-care-kit
@othmane7413 Жыл бұрын
I have a Mercedes vito Any garage in London do that because it’s need to lift the car to do a proper work
@Lanoguard Жыл бұрын
@@othmane7413 Hi, here is a link to our application centres map, www.lanoguard.co.uk/pages/application-centres if you cannot find any in your area we have had customers purchase our product and asked their local garage to apply it for them. Hope this helps
@KennieFabled 2 жыл бұрын
Can you paint over this?
@Lanoguard 2 жыл бұрын
Hi, Lanoguard should be the last product to be applied. If you paint the underbody of your vehicle make sure that the paint is fully cured/dried to its finally state before applying Lanoguard. Lanoguard when fully cured (take 7-10days) it dries clear and will still be as effective if applied over paint. Please let us know if you would like more information or have any more question.
@sandeeppatel2627 Жыл бұрын
How long does this stuff last on the car? Is it an annual process?
@Lanoguard Жыл бұрын
Hi, Lanoguard has been designed as an easy to apply once a year regularly applied coating. And which you can simply apply as part of your regular car care routine. You can apply Lanoguard coat on old coat, which makes it very easy to do a top up and when you apply a coat on a previous coat, that new coat affords more protection than just an initial first coat, so you are building up deeper protection. However, if you do not top up yearly, then the efficacy of Lanoguard is affected. Ultimately, it is ultraviolet and exposure to oxygen that will break the surface of Lanoguard down and weaken Lanoguard ‘s ability to maintain all its technical features and properties, such as self-healing non-cracking, acid and alkaline and petro resistance, waterproof properties and all the other features which makes Lanoguard effective. All this said Lanoguard will go on to protect the vehicle beyond 12 months but for how long and what properties remain intact we could not really quantify or state. Therefore, we suggest topping up yearly. Hope this answers your question.
@jamesmackinlay2500 Жыл бұрын
Just watch your video. Looks great. I normally use waxoil. Can I spray over the top of it . By using your product.??. How do you clean out the sprayer.i will be ordering same very soon. Just need the ok of her in doors.😊😊
@Lanoguard Жыл бұрын
Hi James, thanks for the comment. Yes Lanoguard can be applied over pre-existing under seal. All that is needed prior to applying the Lanoguard is a jet-wash, remove any loose/flaking rust and poorly adhered underbody treatments. Wait for the vehicle to dry and make sure the previous underseal is cured to its final state, then apply the Lanoguard straight over the top of it. Do regularly check any areas where existing under seal products were prior to Lanoguard being applied over top, to ensure any old coating areas haven’t come off which could potentially take Lanoguard with it. The best way to clean the sprayer is either with our Lanoguard Remover and Gun Wash or warm soapy water and then rinse through with warm water. I hope this answers your questions, I hope you get the ok from indoors and please do let us know how you get on.
@nbandpinportugal 2 жыл бұрын
Shouldn't you do inside the box sections first with a 360 degree nozzle ?
@Lanoguard 2 жыл бұрын
Hi Neil, it is personal preference whether you choose to use the 360 injector wand first or spray the Lanoguard, doing either way will not impact the effectiveness of Lanoguard.
@nbandpinportugal 2 жыл бұрын
@@Lanoguard Ah, now I know one is available. Cheers.
@peterhancock8011 Жыл бұрын
@@Lanoguard Do you have a video of how to use the 360 injector wand? Does it work from a trigger spray, or does it need the pressurised pump?
@Lanoguard Жыл бұрын
Hi @@peterhancock8011 yes we do - here is a link to our KZfaq video about it kzfaq.info/get/bejne/fK9naLxnv7ibc58.html we also have a blog our website, which has further information about it - here is the link - www.lanoguard.co.uk/blogs/news/protecting-your-inner-chassis-with-lanoguard-our-360-injector-wands Also yes it works with our Trigger Sprayer and 1L Professional Sprayer. Hope this is helpful
@TheSpragz Жыл бұрын
Don’t you need to mask brake disks?
@Lanoguard Жыл бұрын
Hi, thanks for your question - Lanoguard is a safe product to handle and to use. It is also non-harmful to animals or the environment, jet-wash resistant, non-perishing, non-conductive and non-flammable. It is safe to use on rubbers, plastics, and metals without any issue - so no masking up is needed, but the areas to avoid are the brake discs and pads, so we would suggest covering them while spraying areas near them. I hope this answers you question
@interceptor-ss8kb Жыл бұрын
I owned a Discovery 4 and rust was the least of my problems what piece of sh## it was.
@JohnSmith-ws1dp Жыл бұрын
Doing this without treating the rust first is a waste of money and time. You have to go over the whole underneath of the motor with kurust or equivalent. Let that dry and then give it underseal/weatherproof. Also the inside of the sills chassis rails and wings are a must. Your also better removing the bumpers
@Lanoguard Жыл бұрын
Hi John, Lanoguard is actually great for chassis with surface rust. Lanoguard completely hermetically seals to the surface below rust. It doesn't remove rust per say, but it stops the rust dead. You don't need to remove surface rust prior to Lanoguarding as its creeps below surface rust sealing to the metal below. Lanoguard displace all moisture and oxygen, protecting the surface. Just make sure any flaking or loose bits of rust are removed. Lanoguard over time will push off oxidation too, so it will improve and nourish the surface in the long term. You may find this blog we have written about using Lanoguard on a rusty vehicle of interest - www.lanoguard.co.uk/blogs/news/using-lanoguard-on-very-rusty-vehicles We spent a long time developing a 360 Injector Wand which is designed for box sections, sill and those hard areas to reach - here is a little video with more information and showing how the 360 Injector Wand works - kzfaq.info/get/bejne/fK9naLxnv7ibc58.html. I hope this offers some information about how Lanoguard deals with rust.
@dolebandit9942 Жыл бұрын
I would not go as far as to say it`s a waste of time and money, Obviously it`s better to do this type of thing in the summer, Thus it`s warm enough outside to sand corrosion and apply some paint, But it you give it a really good wash under the vehicle, And apply this product, It should help, I have watched the " Car Focused " White Ford Fiesta ST video using this " Lanoguard " He did not have the advantage of a hydraulic vehicle lift, Just car ramps, But he seemed to manage it, The reason I think it`s not a waste of time and money is it`s not one of those discredited tar paint type underbody products, Those are notorious not just because the just hide and encourage rust by trapping water, They require extensive preparation, This is just some sort of soft wax type product, That is brushed on or lightly sprayed on
@MrJohnnyquark Жыл бұрын
Bilt hamber hydrate 80 is also a good rust converter. I see lanoguard more as a top layer protection, after all the rust has been dealt with
Lanoguard - Underbody Rust Protection
Рет қаралды 17 М.
Lanoguard - Underbody Rust Protection
Рет қаралды 27 М.
Life's Projects
Рет қаралды 26 М.
Дмитрий Иваницкий
Рет қаралды 2 МЛН