Starter fluid trick was sick! Great straight forward video. Thx bud

Thanks. I was having problems removing the rubber cap and wanted to make sure there wasn't something I was missing....Finished watching to the end. That is a GREAT idea, using the grinder to make the tire removal a lot easier.

Now see, I have watched a few videos on how to do this, and this is the first one that is useful. Thank you. You see, as a teenager I worked in a garage. I KNOW how to change a tire. But what everyone else who made a video on this subject seems to overlook is the fact that i DO NOT HAVE a pneumatic tire press, nor a tire machine in my garage! Big ass C-Clamp and a grinder. Now those I have. Roger that, buddy. This will work. Thanks again!

Thanks for the video! One of my tires got damaged so I had to take off to go get a new tire. When I went to put back on, i noticed the small metal pin/key and was wondering what it was. The one the axle was turned it was upside down so I didn't see the slot. Your video made me realize what the metal key was for and how to properly put the tire back on.

Good video! I've seated beads without the fire, just a strap around tread and adjusting tire body while adding air. Most times it works.

Thanks for video, don't have the same rider, but helps understand how to change tire

So you don’t grind the new tire to make it easier to put on?? 😂

The starter fluid to explode the bead in place is amazing!

helpful, I like the idea of using the c clamp

Great video, thanks! My tires were severely misshapen due to being packed for shipping. To seat the beads, I had better luck leaving the strap off, then using the starter fluid.

Now for everyone: Be careful when you use this beading method. I used a strap to bead up a tire on a dolly recently. It WORKS. But...when you go to let loose that strap...it's going to pop back at you. It caught me in the thump and it was very painful. Just wear some thick gloves when you get to that part.

Sometimes these rubber caps get hardened up a bit and it helps to warm them up before you take them off. A hair dryer or heat gun on low.

Yeees it worked boom!! Be safe all . Tie or anchor it to be safe

Thanks, I got a 1970 John deere 110 and I’m restoring it and I got new tires but I’m only 13 so I’m not sure how to get it off thanks so much.

Can you tell me exactly what kind of fluid you use? I have tried small engine starter fluid, and charcoal lighter fluid so far with no success. Should they work?

How do you put a tire on a lawn mower rim?

hi bob i have a s130 has 20x10 rear tires,do you know if the rim is for the 20x8 -8,and if that size will fit them,thanks good video

Yea i dont remove the rim i just deflate the tire then drive the tractor to break the beed and the tire comes right off with the correct tire iron and the other one slides right over the rim with dish soap..use the weight of the lawn mower to take tire off rim...easy 5 minutes. Thats to much messing around with the rim. Work smarter not harder.

Antifreeze to make rubber slide like fresh ice!

What size C-clamp are you using?

Stupid question but what does it mean to set the bead and what is the bead

Are you using JD OEM replacements? I’m looking for a third party new set due to winter rot.

I was with you until you set it on fire. I'll leave that to the fellas. Thanks!

E clip is hard to get back on

You shoud use spray more soap lube so tire can go easy

Good video. Please, for the love of Jesus, do an update video where you clean the mower deck. That thing is DIRTY. No way to treat a John Deere...

For $20 more you can buy one already on a rim.

any way to set the beed without igniting it on fire?

Why you aint just grind the old tire off lol

Noooooooooooo😱😱😱😱man, how are you going to cut the old tire?????? That old tire should work as a spare, or for a go kart.