No video

G Body El Camino Manual Brake Conversion: Success or Failure? 🤔

  Рет қаралды 1,707

Snow Family Racing

Snow Family Racing

Күн бұрын

If you're wondering how well a manual conversion can work on a G body El Camino, I’m finally getting to the bottom of the issues I’ve been having with this one. There’s quite a few things that needed to be addressed and I found an issue that I found extremely surprising as to why this wasn’t working so well with the parts that I had. If you’ve been considering making the swap, here’s some things to know going into it and how to get past them!
I’m making a change from the ⅞” bore master cylinder to a 1” bore master cylinder. I’m using a Wilwood Master cylinder with a 1” bore, here’s a link to it jegs.ork2.net/ZQLkLz. I’ve been working with @BruceCoggins on this project, this master has been used successfully in other manual conversions using very similar parts in a front disc rear drum arrangement. The old master was not really generating the braking force to feel confident in the brakes.
After bleeding the Wilwood master and installing it, I turned my attention to the other ⅞” bore master. I set it up in the vise to see what happens and which brake circuit flows first. I was extremely surprised to see the disc brake port begin to flow fluid only after ⅜” of piston travel. No wonder I was experiencing such a long travel of the pedal before the car really wanted to slow down. By comparison, the Wilwood practically flowed through both ports at the same time. I’m suspecting there may have been an issue with this master and I’m only now catching it.
With the new Wilwood master mounted to the firewall, the brakes were bled using a custom tool I made for this purpose, and the El Camino was ready for its test drive, and it seems like things are moving in the right direction!
#GbodyElCamino #ManualBrakeConversion #snowfamilyracing #Wilwood
Here’s some links to stuff I like to use! These are affiliate links and I may receive a small commission at no additional cost to you.
Greezyz Grip Wipes greezyzgurage....
PWRCORE 12 Brushless 12V Drill Driver & Impact Driver- imp.i284638.ne...
PWRCORE 12 Brushless 12V 3/8'' Impact Wrench Kit - imp.i284638.ne...
PWRCORE 12 12V Mechanical Light Bare Tool - imp.i284638.ne...
Kimo Electric Ratchet - amzn.to/3XQLpYO
Topdon Jump Pack - Use code SNOW10 for 10% off at checkout through my link - topdonusa.com/...
Want to start a KZfaq Channel? Go here! vidiq.com/Eric...
ease check out my partners and affiliates!
These are affiliate links and I may receive a small commission at no additional cost to you.
Racesponsorshipscourse.net- use code ERICSNOW10 for 10% off the Race Sponsorship Bootcamp
WavWatch.com - Use Discount Code ERIC100 for $100 off of Frequency Therapy to better your life!
Sweetbathandbody.com - fine artisan soaps including the amazing Scrubbie Bar for greasy working hands
Topdon Jump Packs - Great easy to use tools to keep you up and running! topdonusa.com/...
Greezyz Gurage - Liquid Pumice soap and skin care products greezyzgurage.... Family Racing
Division 7 Real Estate - www.division7r... - your northern Utah real estate connection
Master Muffler of Clearfield, Utah - m.facebook.com... use code Snow Racing for 10% off your service
ContingencyConnection.com - supporting grassroots motorsports
RMSTATOR.com - ATV, SXS, Motorcycle and Snowmobile Electronics
Velocity Racing Carbs - / velocity-racing-carbs-... amazing Carburetors built for your needs

Пікірлер: 19
@MrZubor
@MrZubor 11 ай бұрын
Great job!
@SnowFamilyRacing
@SnowFamilyRacing 11 ай бұрын
Thanks!
@1Coolbanana
@1Coolbanana 3 ай бұрын
Hey man, great job. Would you still use the 1" master if you had discs all around?
@SnowFamilyRacing
@SnowFamilyRacing 3 ай бұрын
I do not know. Given how quickly I heard back from Wilwood, I'd reach out to them and ask.
@greezyzgurage
@greezyzgurage 11 ай бұрын
I prefer the Wilwoods MC as well!
@patcaro7072
@patcaro7072 25 күн бұрын
Do you have stock or upgraded brakes on the front? And your set up is manual correct? No assist
@SnowFamilyRacing
@SnowFamilyRacing 25 күн бұрын
It's stock parts, stock calipers, stock rotors and a manual set up. I do have braided hoses from the frame to the caliper. The one change I would make is a 15/16" Wilwood Master. I've talked with them after I made the swap and they've suggested the 15/16" master to be the ideal for this set up.
@kevinarce6120
@kevinarce6120 9 ай бұрын
My pedal feel is horrible I have to slam my pedal all the way to stop at how do I fix this
@SnowFamilyRacing
@SnowFamilyRacing 9 ай бұрын
Sounds like the master may be issue like mine was.
@welcome2cali946
@welcome2cali946 3 ай бұрын
Mine starts to jerk when I'm almost to my stop 87 monte Carlo
@SnowFamilyRacing
@SnowFamilyRacing 3 ай бұрын
@welcome2cali946 could be any number of things from warped rotors to sticky calipers or wheel cylinders.
@stroomperformance
@stroomperformance 11 ай бұрын
Good luck next month
@SnowFamilyRacing
@SnowFamilyRacing 11 ай бұрын
Thanks!
@onelowzuki
@onelowzuki 8 ай бұрын
What is your pedal ratio?
@SnowFamilyRacing
@SnowFamilyRacing 8 ай бұрын
The factory manual brake hole puts it at 5.5:1. After this video, I've talked with Wilwood, and they recommended a 15/16 bore master cylinder as being more ideal and offering more clamping pressure than the 1" bore I currently have.
@jimmy_olds
@jimmy_olds 4 ай бұрын
⁠@@SnowFamilyRacingdid you change to the 15/16”?
@SnowFamilyRacing
@SnowFamilyRacing 4 ай бұрын
Not yet, I've still got the 1". I do intend on changing to the 15/16" bore per Wilwood's recommendation.
@jimmy_olds
@jimmy_olds 4 ай бұрын
@@SnowFamilyRacingI have the same 7/8” bore MC like the one you replaced but haven’t plumbed it yet. Now I’m concerned! Lol Did you retain the OE proportioning valve?
@SnowFamilyRacing
@SnowFamilyRacing 4 ай бұрын
Yes, it would have been easier if I hadn't tried to plumb a line lock in. In one of the brake conversion videos, I show how the 7/8" master cylinder flowed. The one I had flowed the rear brakes long before the fronts started to flow. My 7/8" master may have had an issue, I don't know. Keep an eye on how your ports flow when you bench bleed the master. That will tell you what you need to know.
Manual Brakes that Actually Work | Tech Tuesday
37:04
Busted Knuckle Off Road
Рет қаралды 24 М.
The El Camino Needs a Manual Brake Conversion!
18:58
Snow Family Racing
Рет қаралды 1,5 М.
女孩妒忌小丑女? #小丑#shorts
00:34
好人小丑
Рет қаралды 83 МЛН
When you discover a family secret
00:59
im_siowei
Рет қаралды 15 МЛН
白天使选错惹黑天使生气。#天使 #小丑女
00:31
天使夫妇
Рет қаралды 14 МЛН
拉了好大一坨#斗罗大陆#唐三小舞#小丑
00:11
超凡蜘蛛
Рет қаралды 13 МЛН
Project Car El Camino: Ep 7 - Disc Brake Conversion!
20:42
Budget Build Garage
Рет қаралды 34 М.
94-04 S10 / Blazer Manual Master Cylinder Conversion Install
17:02
Motion Raceworks Official
Рет қаралды 45 М.
How a Brake Booster and Master Cylinder Work
7:19
speedkar99
Рет қаралды 1,6 МЛН
Brake Tech 101 - How to: Manual Brakes
16:08
RMJ Motoring
Рет қаралды 5 М.
How to | G-Body Rear Disc Brake Conversion
16:01
Inline Tube
Рет қаралды 102 М.
Motion Raceworks Manual Brake Master Install on 93 S10
19:12
CheapSkate Nation
Рет қаралды 466
Avoid Doing This! Incorrect Brake Master Cylinder Setup Discussed: Tech Tip Tuesday
14:38
Power Brake Conversion on a 4th Gen Nova with 3rd Gen Parts
29:27
Three Rivers Wrench
Рет қаралды 1,7 М.
MANUAL OR POWER BRAKES ??? Whats stopping the Turbo LS Monte Carlo..
40:24
女孩妒忌小丑女? #小丑#shorts
00:34
好人小丑
Рет қаралды 83 МЛН