Best video I’ve seen yet , couldn’t find anyone with this info before hand so I had to go on alldata to find this info out ! But it’s great to see a excellent video and advice bits thumbs up will be sharing with other VQ friends !

Very nice of you to spend the time and make this video. I imagine your video has helped many people. I truly appreciate your video!! GBYAY!!

This helped me tremendously. I had no clue to put it on ramps or lift the front. My dad was like, since when do you need to lift the front to bleed a car? I said this isn't a car, it's an Infiniti. Haha

Thanks for the advise about the bleeder, I changed out me radiator over the weekend and didn't mess with the bleeder.

theres like ten different ways to bleed the coolant and this is the easiest most clear way to do it thanks

Another good tutorial. I remember when mine went bad when I first got my car. Definitely not a fun experience to drive the car to the shop constantly pulling over to the side to cool down.

Thanks bro. This helped out alot. Was having over heating issues.

Best video I've seen thank you so much is very helpful.

Awesome explanation bro! And I love the coolant paint job 😋 Subscribed. 😃

For anyone having issues I did mine a while ago and I'm gonna have to do it again in like two days haha new Thermo and rad going in lol yay me. But for bleeding I found it really easy to follow the service manual instructions. I didn't completely open the bleeder though just unscrewed enough to where you hear air escaping. Then basically got a rock and pressed the gas pedal to the specified 3000 rpms. Squeezing hoses helps. And then sit back and drink a beer and something and watch the bleeder an temp. Didn't take long when I started doing it like that. But took like 6 normal cycles for me before that. Great video man!

Finally a good video

Man i wish we had friends to do these crazy mechanical stuff and tune up

perfect video ! thank you man

Yo we fb frendz my boy. You helped a brother out today 👌

Thanks, great video.👌🏾

Buen video me gusto como lo manejaste en la nieve 👍🏻👍🏻👍🏻👍🏻👍🏻fast and furios jeje

So I’ve been having a issue with mine I’ve been trying to bleeding it for like a week now and I keep getting air and it dumps into my overflow tank, I replaced my thermostat and hoses also installed the bleeder valve because I got a motor swap and it just had a heater hose connector. Do you believe it’s just air in the system? Because my head gasket is fine and everything else is fine

ive tried 2 new thermostats. bottom hose is cold and hard with pressure but no thermostat opening. i have decent heat and the motor is going 220 idle and higher driving.... air behind the thermostat? how do u get it out?

Why does my radiator hoses have little pressure and not hot? The car doesn't overheat, and no engine light? Is anything wrong?

I have replaced my thermostat and radiator cause the seam was cracked on my radiator. I'm having trouble getting the system bled properly. Is there like some special touch to bleeding this system smh I have an 04 coupe with only 150k miles..

hey what was that part called at the begging that you said to always check?

hey man im a really big fan , and i have a 350z project i just put and brand new swap in it and im having trouble bleeding the system i followed ur procedure and my thermostat isnt opening and car is blowing cold air at idle and at temperature and if i rev it it will start to over heat and the funnel will over flow and spill everywhere, and for some reason only my driver side fan is working the passenger one doesnt work now and i feel like its leaking a lil from the passenger side of the radiator, like when i didn’t replace the thermostat before the car will run fine for a good 1hr30 and then if i take it for a test run and back then it will start to overheat and blow cold air and now that i changed the thermostat its not opening and the car overheats faster now so and when i tryd pouring coolant , no coolant came out of the bleeder screw 😕

Your awesome man!!

Do you recommend opening the bleeder while car is running? And at normal operating temp or just at the beginning? Won’t it squirt out when running? Thanks for this video

I’m about to put my oem thermostat in cause the one Frm AutoZone def don’t open for me

Would I have to bleed the entire system if I'm just replacing one hose? It's the top radiator hose that is next to the overflow tank. Just asking before I do the job. Thanks!

Awesome video 🔥

so if my hose on my thermostat side is cold and I just put a new thermostat. you should suggest my water pump?

how exactly do you know when your done? i might have missed you say it but idk how to tell when i’m done bleeding. also how long should this take

If you don’t have a way to lift both sides of the front up, could you possibly park it on a hill with the front going up the hill and have the same effect?

So I changed my radiator, got a new thermostat, bled the system (there’s no more bubbles coming out of the bleeder screw) there’s still no hot air coming out and it’s overheating. Is it that there is still more air trapped in there or is it something else?

Great video brother, I need one of those funnels tho because, I got the "bubble blues" now !

Do you have to change the thermostat or can I just bleed it to take air out the system?

I am currently bleeding mine right now, I'm on # 5 and i finally have heat but not at idle, wont air be pulled into the system if i open the bleeder with the car running ? And are you opening the bleeder with the car at operating temp or just as its heating up ? Great Video !

Hey man I got a question, I got my engine swapped and the swappers deleted the bleeder valve.. am I SIL or can I still bleed without the screw?

That angle kit tho lol

I was having an over heating problem with my g35 also. I replaced the thermostat but it still kept overheating. The mechanic took off the spring on the thermostat so the water is constantly running through now. The thermostat we got from Autozone was different from the original but it’s supposed to be for a g35..but I see everyone else’s is different as well and seems to work fine. But just not my car. A new radiator was put on and was bleeded as well while installing the new thermostat. What you suggest? Should I find an original thermostat? It’s about to be winter and I can’t just get up and go in my car.

I’m not sure if you’re still answering questions - but I have my AC and heat deleted/not working- can I still bleed properly without the heat on ?

Thank you good sir

Hey at what point will the coolant come out the bleeder. Nothings coming out of mine

Do u have to jack it up

How would I know if the system has bled bro ? And should I turn off the car after it’s done ?

My car is overheating, the temperature goes up only when I park and when driving on freeway 😩

Bro get a z1 aluminum undershroud it is so worth it and Will keep the underside clean and safe

If the heater works, does that indicate that the thermostat is working properly? I have my G35 on ramps, no leaks, but the coolant reservoir was empty which is where i think air entered my system. I have bled the system 5 times now, each time bubbles show up in the reservoir, but i still am overheating. reservoir is now at max and has gone down over the last 5 bleed cycles. Any suggestions?

abour how long did it take

Nice vid.mines ran hot on me today. What brand thermostat ya used?

Hey brother what exhaust set up are you running?

Can you tell mewhat the tork was for the bolts

I didn't drain my radiator is that a problem

Ok so I need some help I filled the radiator up as much fluid as it would let in, I have my over flow tank hanging from the top of my hood with coolant in it, put the cap on the radiator, turned the car on, turned the heat high as it could go and also the fan for the AC everything full blast on 90 degrees circulating in the cabin and I let it run for about 5min total and i got one good air bubble out of the bleeder valve all other times it was just spitting coolant out and no air and that big hose at the bottom is cold and it was blowing out freezing air from the AC no hot air... And idk what the hell to do now so someone plz help me id appreciate it. Everything was working fine before I decided to bleed this coolant no problem with my thermostat or over heating i just wanted to change my coolant due to the summer time approaching.

Can air get into the system from just topping off the reservoir? I put more coolant in my reservior one day and the following day my car started overheating

On a 2004 350z is the bleeder the green nozzle?

Just a quick question why would the thermostat open if the pressure and temperatures were the same on both sides it supposed to regulate when the temperature reaches a certain temperature which also means it's reached a certain pressure to collapse the spring ,it's not electronic it's mechanical if you were able to hold the thermostat ,pour that water in, i still doubt that test would work.. who taught you that ?.. i'm here looking for a solution for overheating in the g35... i wasn't on here to rip on you.. i still appreciate you posting information.. if that really works i'm sorry but i'm really mechanical...

"If not done this way there is 100% going to be air pockets in the system" Even if i use a coolant air-vac?-nmv saw ur other vid!

I replaced the thermostat today, and it's not opening, all the coolant starts to boil and rise overflowing and making a mess . I'll probably put the original back on. Duralast crap

Man I had my heat hot at idle for a couple of minutes thought I was good to go. Well after driving my car for about 20mins it overheated. The bottom radiator hose is not getting hot.. I just replaced my thermostat too. Could this be my water pump?

So would I still be able to do this if my climate control unit doesn’t work? Currently can’t use cabin heater bc I’m ordering a new climate control, but need to drive my car before it comes in mail

Do you know the nissan part number? Thanks

Where is the purge line for the 06 350Z

so i did the process and my car was good for 2 weeks and now theres no heat at idle and the bottom hose that goes to the thermostat is cold at temperature qnd temp line acts up but when i drive the car is fine and starts to blow hot air 😕 its like the thermostat kicks on at like 3-4 rpm but when i let off it starts to get cold agian at idle and line acts up and blowing cold air , new thermostat/overflow tank and hose replaced only and there is no leaks

I.think my thermostat is bad on my 08 m35 or my temperature sensor is bad

I have no fluides coming from the bleeder

Where are you guys located?

Please help me

if i don’t jack the car up can i still bleed the air ?

My overflow keeps overflowing 😂

hey the idiot owner before me stripped the bleeder, I bought a new one but I can't get the old one off (it has stupid screw clamps instead the squeezy kind), what would you recommend me do to bleed it and regain heat? I can provide pics

i bled the air out of mine like 10 times.....still no heat comes from the heater smh

You need a shield under there to deal with that salt bro.

eech...driving your car in the winter huh?

Put a damn year model of the car

I hope you washed this damn thing. lol

front camber is no good