Volkswagen TDI Cranking But No Start Fault - Found & Fixed

Volkswagen TDI Cranking But No Start Fault - Found & Fixed - How To DIY

Рет қаралды 438,794

3 жыл бұрын

Cranking / turning over but failing to start on a VW 1.9 TDI engine.
In this video I go over the process on how I found and fixed this fault.
Exact vehicle details : VOLKSWAGEN CADDY 2K 1.9L BJB, BLS SOHC 8v Turbo Diesel Inj. 4cyl 77kW 6sp Auto DCT Van FWD [01/06 - 12/10] Diesel
Thanks to everyone who watches my videos, Likes, Shares and or leaves a comment. I appreciate everyone of you.
Tool options that I recommend and use. www.amazon.co.uk/shop/gerardb...
➢ For business inquiries Email : gerardburkebusinessinquiries@gmail.com
Disclaimer:
GerardBurke is a qualified motor technician who has completed modules & courses in manual handling and all aspects of workshop safety. These videos are not intended to be used by anyone who is not trained and or qualified to carry them out.
Due to factors beyond the control of GerardBurke, I cannot guarantee against improper use or unauthorized modifications of this information. GerardBurke assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. GerardBurke recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of GerardBurke, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not GerardBurke.
2005 2006 2007 2008 2009 2010 2011 2012
BJB, BKC, BLS, BSV, BXE
Audi A3 Mk2 BKC: BXE: SEAT Ibiza Mk4 SEAT León SEAT Altea SEAT Toledo Mk3 Škoda Fabia 5J Mk2 Škoda Roomster Škoda Octavia Škoda Superb Volkswagen Golf Mk5 VW Jetta Mk5 (BKC: 05/05-??/09, BLS: 08/05 - 09, BXE: VW Golf Plus BLS: 05/07-12/08, BXE: 05/07-01/09), Volkswagen Touran , VW Passat B6, BXE: Volkswagen Caddy Mk3
#HowToDIY #Diagnose #NoStartFault

Пікірлер: 265

@larryallsop9330 2 жыл бұрын

Thank you, you clever man. Unplugging the camshaft sensor was the clue I needed when I had been looking for a fuel fault. If you were here, I’d buy you a drink.

@evertspies3345 3 ай бұрын

If there is still no start with sensor unplugged do I then follow up fuel problem?

@evertspies3345 2 ай бұрын

Exactly what I did. In my case pointed to no fuel from pump in tank. While following to replace pump came across bad wiring.

@felixkalox7637 2 ай бұрын

Mine is doing the same thing need to do that tomorrow morning I was about to buy fuel pump but let me try this

@alainmiclette7634 Жыл бұрын

a real mechanic, not just a parts changer, getting rare....

@donjulio5045 9 ай бұрын

*Good luck even finding a good parts changer nowadays...I'm lead tech and all we getting applying is lazy lube techs that sit on their phone all day*

@alainmiclette7634 9 ай бұрын

@@donjulio5045 good time to ask for a raise...it's been eons salaries have fallen back on real cost of living...

@leehargitt3539 11 ай бұрын

Thank you so much!!! My 2000 Jetta tdi with 419,000 miles (that I put on it) wouldn’t start today. So while I was in a parking lot I watched your video and it was just what I needed to diagnose the problem. My fuel injection pump pulley had slipped 1/8 of an inch from the last time I did a timing belt change a year ago. So I grabbed a socket set and a couple wrenches and 15 minutes later it fired right up and I was able to drive back home 😀.

@liloskii4810 Жыл бұрын

This is the exact issue my car is having now I finally have some direction and know how to handle this. Thank you so much you have saved me so much money

@dankelly9233 28 күн бұрын

How did you get on? I’m having the same issue

@liam-lh2nm 11 ай бұрын

Brilliant video wish you worked at my work im a young apprentice and need someone like you at my work. Very good explanation and really helpful

@WholesaleTurbos Ай бұрын

wifes old car has been sitting for 6+ months, started maybe 3-4 times and not driven. I started to drive it and noticed hard to start when cold. I popped the bonnet to check the battery charge and there were 2 spanners, thinking I left them in there for 6 months after a service, went and checked them after watching your vid and they are 13/19mm, I must have played with cam timing... without lifting a spanner to it, id say your vid has got me in the right direction

@andrewnewton5893 Жыл бұрын

You legend followed this video checked plug to rule wiring out 5v on all tests so adjusted torsion on cam and wow 1st click fired up

@dx_logan 2 жыл бұрын

Lovely video, it's exactly the problem with my Seat Ibiza 1.9tdi 2008. I just noticed by this video that the sensor might not be the problem but yes the camshaft out of position since a cold start will make a knocking noise from the engine. Will be great after 5 mins but since the sensor is telling me something is wrong it's a lot easier to follow this amazing video before blindly buying a new sensor. A 10000000 thanks to you !!

@stevenhyatt3609 Жыл бұрын

Mine at cold start taps for about 5 seconds then goes away.

@darylmiles5862 3 жыл бұрын

Will give this a try in the morning, hopefully it will get it started 👍

@dadwalker3896 3 жыл бұрын

Just helped me out loads on my golf thank you. More videos

@markwatkins3959 3 жыл бұрын

Thank you very much My caddy has been playing up for a month or so cranking over for 30-40 seconds before starting . Adjusted the timing as it had slipped as in the video now starts 1st time

@selloshaun3675 3 жыл бұрын

I’m in South African u just helped me big time...thanks bro 👍🙏🏾

@GerardBurkeBurkesGarage 3 жыл бұрын

Great stuff 👌👍🙏

@charleshoward1475 Жыл бұрын

You may have just have saved me a small fortune. I was losing hope to an extent. I drove the car parked it up, then it refuses to start that Evening. Servicing has been kept bang up to date. Interestingly its timing belt, and water pump were replaced only several weeks ago. It has been such an easy starter to date, and was seemingly running nicely. It delivered 65.2m.p.g running up to Morecambe and back to Cornwall. I've precious few pennies to replace the car with at this time. If Your advice pays off here Gerard I will really need to send you a decent drink Sir.. Thank You so very much for posting a clear concise video.

@sufyanmohsin4485 4 ай бұрын

any updates ser?

@Mind-your-own-beeswax Жыл бұрын

Nice job man. Shame I don’t have anyone like you near me who could sort out my P0028. Tried 2 different garages and neither of them seemed to have a clue.

@sebastianuchman3145 Жыл бұрын

Thanks for your video; I just got my engine running.

@user-lz5vg5xo2g 7 ай бұрын

Thank you very much i will try this on my BXE with hard starting issues, we changed injectors and fuel pump still same issue.

@mwalsh3037 3 жыл бұрын

Quality work Ger, that was an out of the box diagnostic find, loved it "bualadh bos"

@wochonglee2191 4 ай бұрын

I recently bought a cheap a vw bora 1.9tdi pd100. Took about 4 seconds to start. So I was looking around the engine bay and noticed the cam position sensor was unplugged and taped up 😮. Plugged it in and no start. Decided to check engine timing. The crankshaft pin locked in and cam was about a tooth out. Maybe a touch more. Retimed it all and plugged sensor back in bingo. Runs like a dream now.

@salvagedb2470 3 ай бұрын

Got a Fabby TDI pulling same stunt but its just had its Head gasket done , but will give your Advice a go.

@kennethbeeler1 3 жыл бұрын

What a great video sir, wow!

@ariantaria2065 3 жыл бұрын

Well diagnosed and step by step explained, great video many thanks 👍

@GerardBurkeBurkesGarage 3 жыл бұрын

Thank you Arian

@patkelly7999 3 жыл бұрын

Great job Gerard, fair play, Thankyou :):)

@GerardBurkeBurkesGarage 3 жыл бұрын

Thanks Pat, the VW will live on for another while 😉💪

@mudassarmehboob7237 Жыл бұрын

Hi, I really liked your video. You explained very well. My car has the similar problem. I’m going to sort it out. Thank you!

@deansmith817 4 ай бұрын

Torsion value is written in pen on the cam cover on them all, usually doesn’t last too long. Supposed to be written in the service manual too. Some can be up to 5 degrees either way, 0.0 is usually the best benchmark to adjust from when doing it.

@antof1235 3 жыл бұрын

Once again, thank you very much

@GerardBurkeBurkesGarage 3 жыл бұрын

Thanks Anthony, I appreciate it 🙏

@imwmanish 3 жыл бұрын

Great work nice video sir love from India ❤️👍🙏

@GerardBurkeBurkesGarage 3 жыл бұрын

Thank you

@ericamannea8148 Жыл бұрын

This was the first video I found with substantial information. Thank you.

@sugar-3-Danny Жыл бұрын

I love you man. Solved my problem 🙏🏼💙😂

@peterwhyte1385 Жыл бұрын

Thank you sir you are a flamin legend

@romanosautomotive 3 жыл бұрын

Nice analysis Gerard!

@GerardBurkeBurkesGarage 3 жыл бұрын

Cheers mate 🙏👌

@Dani-Innit Жыл бұрын

My 2013 Passat TDI just started doing this a few days ago. We'll have a go at it and hope it's this simple. 😁 Ty

@stupot2546 Жыл бұрын

Did it work

@AlmostAwesomeMe Жыл бұрын

i am having the same problems. had me change the fuel pump. and the problem still persists. LMK if you got yours to work

@HichamBelachgar-im2le 10 ай бұрын

Please let me know if it works I have same problem with 2013 vw passat

@jrnkennethberg4903 2 жыл бұрын

Mate.... thank you so much!

@forgottenknowledge8917 9 ай бұрын

All VAG owners become a mechanic in no time, hahaha. I've learnt a lot about TDI because I bought a high mileage VW Caddy 1.9 TDI. Part after part after part has been replaced my me. Things keep breaking at 300,000km. My van is practically new now after all the work I've done to it. It's drive another 300,000kms

@modzgaming4293 7 ай бұрын

I know exactly how you feel I have a 1.9 2009 golf

@luismiguelgamboa9240 Жыл бұрын

Good video and very well explained.

@GerardBurkeBurkesGarage Жыл бұрын

Thank you Luis 🙏🙏

@michaelmajchrzak3476 3 жыл бұрын

Thank you. This is awesome 👍👍👍👍

@GerardBurkeBurkesGarage 3 жыл бұрын

Cheers Michael

@d.d4184 3 жыл бұрын

Nice process.

@GerardBurkeBurkesGarage 3 жыл бұрын

Thanks

@michaljacobs9753 2 жыл бұрын

Well explained and easy understandable. Thanks sure did help

@iankelly2110 3 жыл бұрын

Nice Diag Gerard good Bias voltage 5v on the signal wire the torsion values are as close to zero as possible

@GerardBurkeBurkesGarage 3 жыл бұрын

Cheers for that Ian 👌🙏

@Jay-jl7by 3 жыл бұрын

When testing the signal wire. Shouldn't the cam sprocket be in a certain position? Cam sensor is a potentiometer so surely if in wrong location wouldn't the 5v be pulled to ground thus sending a signal of cam position. Edit... scrap that. You run the test with sensor unplugged. Only relevant when backprobing. Good job. I've worked on loads of these and didn't realise the torsion could be so far out as to cause non start.

@careyautorepairs 4 ай бұрын

Good video this brother, going to save it to my playlist now.

@zanprelovsek995 Жыл бұрын

Thankyou maestro 😘😘

@thulanibhekani2106 Жыл бұрын

Nice video lesson

@binagarten4667 2 жыл бұрын

Great video. 0-0.5 is the tosrion value

@jgegere Жыл бұрын

Great video. 0-0.5 is the tosrion value

@patcarmax 3 жыл бұрын

Brilliant video well explained good work 👍

@BasiaWenda-sd1xw 5 ай бұрын

Good job

@jurtobrauer1566 2 жыл бұрын

good video, it helps👍👍👍

@getachewchala2778 3 жыл бұрын

boss am from aferica ethiopia nice video

@caivinaugustineshumba4736 Жыл бұрын

Thank you so much you really help me sir

@volkswagenpassat5955 Жыл бұрын

Thank youu brother I found my clue

@ahmedamzil4170 2 жыл бұрын

Thanks for this vidéo ,what is value torsion?

@leeleelee1129 Жыл бұрын

Good explanation 👏

@GerardBurkeBurkesGarage Жыл бұрын

Thank you

@colin5064 2 жыл бұрын

very useful and informative video. My question to you is how can l determine on a five pin connector vw golf mk6 1.6 tdi. which pins relate to +5v and _5v on the air intake swirl valve motor. Not easy to find access to a wiring diagram for this. As l suspect the swirl motor and wish to see if it functions on the bench 6

@mikeyb1281 3 жыл бұрын

Nice 👌 Top presentation 🍻

@GerardBurkeBurkesGarage 3 жыл бұрын

Cheers Mike 🍻

@melusimpungose6453 3 жыл бұрын

You work nice man,vw power 4rom South Africa

@GerardBurkeBurkesGarage 3 жыл бұрын

Thanks Melusi

@MiracleMAX 3 жыл бұрын

Nice diagnosis mate & good details 😊

@GerardBurkeBurkesGarage 3 жыл бұрын

Thanks mate 🙏

@Wrensspeedshop 2 жыл бұрын

My 06’ starts are idles nicely, it’s only once you press the throttle the RPMs gets up to roughly 2000 and the motor starts jumping like it has a two-step then the tachometer drops to zero and the glow plug light comes on. Anyone else have a similar issue? I just want to make sure I’m swapping out the correct part lol. I’ve checked VCDS and it doesn’t seem to be throwing the code many have mentioned. I appreciate any help and and thank you for the video and the information within.

@mikalji 2 жыл бұрын

Hi Gerard, Thank you so much for sharing such in-depth knowledge, much appreciated. By the way, where are you based in the UK?

@ThePlombyras 9 ай бұрын

nice tip

@Sean-md6dw 2 ай бұрын

I have the same symptoms about the vw tdi engine but without the fault code as well as your ,so I need to check out the fuel pump or injector.

@user-uf8xm6qd1b 9 ай бұрын

Like your videos, very helpful. Question, on your crank sensor VW 1.9 TDI 2001, both outer terminals are negative. What might be the best place for me to start looking I have no positive terminal

@johnburns6422 2 ай бұрын

You are Good could do with you in Letterkenny area of Donegal

@lancecooper4646 3 жыл бұрын

We used to have a dude like you at our work but unfortunately he left & as far as I know, he's out of the trade, it's a shocking waste, he'd make an excellent trade school teacher 👍

@GerardBurkeBurkesGarage 3 жыл бұрын

Thank you Lance, I appreciate the comment. It's such a shame when we lose good techs to other jobs or roles. They are needed badly these days

@stanmanguma9114 2 жыл бұрын

@@GerardBurkeBurkesGarage I have a jetta 6tdi it does not make start. If you put quick start on it it will start bt it does not Rev. No power at all. I tested the injectors they are 100 % correct. Vcds is showing nothing.

@bobirving6052 8 ай бұрын

Must be running to set torsion values.

@bobirving6052 8 ай бұрын

Possible MAF problem or intake air leak.

@bobirving6052 8 ай бұрын

If you have a lift pump, make sure it is providing pressure.

@marystevens6723 2 жыл бұрын

My 03 beetle is doing the no crank thing and I hope this is the answer.. thank you for the video!

@bobirving6052 8 ай бұрын

Probably air leak in fuel line or injection pump.

@philfjfry1 2 жыл бұрын

I have same issue. Its all the way to the left. However there's markings from who has changed it previously and it lines up with them. Should I still move it to the centre?

@aymenmohamed1134 8 ай бұрын

Awesome

@GerardBurkeBurkesGarage 8 ай бұрын

Thanks

@upupandaway5646 2 жыл бұрын

HELLO I changed my clutch soliniod and disconnected battery ..now won't even crank .any Ideas .thank forthe great video

@chrisjohnson460 2 жыл бұрын

So I have a 2013 Passat tdi 6 spd manual. Once in a while after driving my car I go into a store come out and try to start it and it just cranks over. I sometimes have to let the car sit for 20-30 mins before it starts and I can drive. This doesn’t happen all the time only randomly. Also when the car is on a cold start and I start driving it bucks a little like it wants to take off. Do you think it could be the crank sensor failing? Ps no codes! Thanks so much

@cecilshannon2586 3 жыл бұрын

Thank you very much! I have been fighting with my brm for a while now. I just installed a stage 2 cam from kerma TDI and im not getting a torsion value! I am using vcds and I don’t know if I can see camshaft speed on there. I will try out a couple tips you gave in the video!

@eugeneoreilly9356 Жыл бұрын

You don't need to see camshaft speed,what you need to see is the timing limits within specified tolerance.

@cecilshannon2586 Жыл бұрын

@@eugeneoreilly9356 I got it figured out finally haha it ended up that all 3 cam sensors I got were all bad. If anyone gets one I would get it straight from Kerma. I got 2 from autozone and one from rock auto. None worked except the one from Kerma

@eugeneoreilly9356 Жыл бұрын

@@cecilshannon2586 glad you got it running.

@bobirving6052 8 ай бұрын

I bought cam sensor from Rockauto and it works fine.

@LAW-fv6ys 2 жыл бұрын

For 2.0tdi 16v Inlet cam (Torsion should be 0), the exhaust cam should be adjusted so the live data for fuel consumption is flicking between 0.4-0.6 l/hr. For single sprocket 1.9tdi for example torsion is also 0

@neilappeal20 Жыл бұрын

THANKYOU 🍻

@rosssorensen8485 2 ай бұрын

Thanks for informative video. However my issue is engine will crank but not start first thing. Wait 5 minutes and it starts and runs perfectly. I’ve had fuel pump replaced and ecu checked out. What would you suggest next?

@wesv1986 2 жыл бұрын

So if I have the ign on and use the Muti meter the signal wire should be putting our 5v?

@DavidSmith-jb6wg 8 ай бұрын

Great video Ger my car is in a garage at the moment it had a leak in a fuel line its now repaired but wont start ..

@bobirving6052 8 ай бұрын

Bleed pump and injector lines if it is ALH engine.

@DavidSmith-jb6wg 8 ай бұрын

@@bobirving6052 got it sorted after a week..

@longbar2344 2 жыл бұрын

my project bkd engine'd golf had it's turbo let go. found metal everywhere upto the intercooler but nothing after. replaced turbo and tried to flush oil and put fresh in. it cranks fine but won't fire, was gonna try this but my fault code is p2100 (anti shudder valve) it is clean so a bit stuck. trying to order one but would that prevent the engine starting?

@johnleigh349 5 ай бұрын

Very informative vidio I am having a simuler problem with intermittent start up plus oil light sensor showing after new sensor fitted and an oil change help

@johnleigh349 5 ай бұрын

Skoda yeti 4x4 140 bhp

@shakeeloniel8891 2 жыл бұрын

Hi Gerard thank you for sharing this video, Ive got a vw mk5 1.9tdi in the mornings it wont start i have to use starter spray then for rest of the day starting is fine... can you pinpoint me to a rite direction ? Any help would be well appreciated.

@Kinematographer Жыл бұрын

never use starting spray on a diesel, you could bend a con-rod!

@andrewnewton5893 Жыл бұрын

Bonus just got my golf 1.9tdi BLS engine and it starts after a while noticed cam sensor not plugged in properly she just had full cam belt kit I'll test loom and look for signs as befor this she would fire straight up

@abdulwahedy4569 2 жыл бұрын

Do u know where is inertia switch? ( Fule safety button)

@BigRustyJoe 2 жыл бұрын

Hi mate, great video! I unplugged the sensor and it still just turns over BUT sound as if it’s about to start any minute whereas when the sensor is plugged in it has no interest at all. Any ideas? I think best thing is to re-time it from scratch?

@bobirving6052 8 ай бұрын

If you have a lift pump, make sure it is providing pressure.

@stuartwest1236 2 жыл бұрын

Hi am looking for a bit of advice,my wife was driving my 61 plate Octavia vrs TDI when it just turned off,took it to the garage they changed the crankshaft sensor,then said they noticed moisture about the ECU but they thought it was another sensor behind the gearbox, gearbox was removed and sensor was checked and all fine,put new clutch in car while the gearbox out, got car back been starting and stopping and then broken down again,towed to other garage and now saying car has no compression.

@sugar-3-Danny Жыл бұрын

So will it make it out of time if u loosen the bolts

@ajmalbangash8374 Жыл бұрын

Nice systematic diagnosis there. Could it still be a camshaft issue if the fault is intermittent? I've got a 2 litre tai Passat 2011 B7 that does this intermittently.

@c938695 Жыл бұрын

I'm having the same intermitent problem on my 2010 2.0T EOS

@samuesoeilyoriy6581 3 жыл бұрын

nice fix gearld. i done a lot of these non start over the years and the first thing i always ask is did the costumer put in wrong fuel 😆

@GerardBurkeBurkesGarage 3 жыл бұрын

It's the right question to start with 😁

@amarmatloob9624 9 ай бұрын

Hi, I have an Audi A3, cranks and just about starts and then runs rough. On acceleration it only gets going when at 3k RPM, however when it gets hot it seems to get much smoother and accelerates from 2K rpm. Has glow plug control module codes and also all injectors upper control limit reached. What can it be? Thank you

@AA-bw2hy 2 жыл бұрын

My wv touran 2.0 dsg,have problem and,sometimes dont start,and one mechanik get out my radio,think radio lost energy on battery.but again same problem dont start.What doo y think?!

@JohnHarryShaun 6 ай бұрын

I have a 2.0 pd, cut out, won’t run, gravity fed the flow to tandem pump, and vacuum can on the return, I can’t get anything back from the return cranking or not, therefore no flow to the injectors. Do the tandem pumps fail like this???

@vsg4467 5 ай бұрын

Will these steps work on the 2.0? I have a 2011 that intermittently doesn’t start when it happened the p3007 code popped up but went away after it finally started

@gambit_toys6554 Жыл бұрын

I tried unplugging the crank sensor no luck. *correction* I tried again and the engine started without the sensor! Car is running 08 Touran 1.9 tdi 364000kms. Thanks!

@frenchwithmoufdi3776 2 жыл бұрын

U0155 error code for my passat cc 2012. I have changed the battery 🔋 but still same problem in the morning juste??

@home8706 2 жыл бұрын

i have the same engine and i need to ask can it just stop or can the problem get worse over a cple of days? Mine started after i parked it up drove it started making a screeching noise took home parked up was told it was the turbo but no smoke just loss of power then it wouldnt start i have smoke coming from the join to turbo and also down the air intake pipe but now it just doesnt run did show turbo boost preasure sensor fault that was it i need help

@amarmatloob9624 9 ай бұрын

It's a 2L TDI, BMN engine 170bhp, 2006

@romankorol4378 2 жыл бұрын

I got 2006 jetta tdi and similar problems, but mine cranks really hard and doesn't start. I tried to do what you did and not start and no codes. What else could be ?

@turdpolisher8410 5 ай бұрын

whats it mean if you get 12.3v fully battery power with the ignition on to the plug? Pin 1 and 3

@gowenrv3762 2 жыл бұрын

I hope you do more Volkswagen TDI diesel engines. I have one that starts sometimes... sometimes it don't. Come back the next day and it will start. LOL Beats me.... My wife is about to scream. LOL

@gowenrv3762 2 жыл бұрын

@@Lee-eu6wf Thinking I may have the solution... EGR valve LOL

@kyleohara1949 Ай бұрын

just shredded my timing belt a few days ago. Not sure if i did any damamge. Belt is still on but missing a whole section of teeth. ill have to check timing and see. wish me luck

@soundofsuperbad7978 7 күн бұрын

Thanks for this video. Does anyone know the correct torsion value for a BLS engine code 1.9 TDI in a 2008 Audi A3. I have searched but nothing conclusive. Many thanks

@MichaelGriffis Жыл бұрын

I have a 2012 VW Passat TDI SE; I'm trying to locate this camshaft sensor connector as seen in this video at 11:34. I can not find it.

@abdulwahedy4569 2 жыл бұрын

In my fule pump only 0.50v electric going, it should be 12v, where will be the problem?

@mariusrusu7741 4 ай бұрын

Hello and congratulation for this video. I have same problem with my Caddy, year 2010 , 1.9 TDI, 77kw, 2k ACBLSX01 engine. All the symbols appear on the board when I turn on the ignition, in this case I have excluded some releys. Like in this video I disconected the sensor but engine it still won't start. Could you give me another suggestions please? I'm not mechanical but some timebut I like to solve problems myself . Thank you I don't know if it helps but the engine has 108,000 real km on it.

@ricardopinto1765 2 жыл бұрын

I'm having a misfire (esporadic) error code on cilinder number 2 p0302/00770 on my VW Passat b6 1.9 TDI! Do you think this camshaft position can be my problem? Change recently spark plugs and wires Cable! 👍👍👍

@noelmarodza4957 Жыл бұрын

Had the same problem with a jetta 5.it would start nicely idle nicely but when it got to normal operating temp it would start to misfire and splutter sporadically only to find out the crank sensor had a chip on it.change the sensor and booom the problem was solved

@Iosif.dumitru01 Ай бұрын

Hi, I have a 2.0 bkd engine, it starts really slow in the morning. I changed the battery, injector orings and glow plugs, but still starts really slow in the morning, after 2 cranks.

@Gdljal24 Жыл бұрын

Hello there I have Signal on Pin 1 (4v) Pin 2 (3v) Pin 3 Is ground and my Caddy still doesn’t start but it does start with the camshaft sensor disconnected I put a new one in and still doesn’t starts