Here's how the Toyota 3.0L V6 Engine Became a Success

Рет қаралды 125,405

2 жыл бұрын

In this video the 1MZ-FE 3.0L V6 engine is torn down and analyzed. This engine is known for its longevity, reliability and smooth operation, albeit a lack of power according to modern standards.
The 1MZ-FE engine was overbuilt for reliability and the ability to take forced induction from the available TRD Supercharger at the time. The 1MZ-FE was produced from 1994-2006, used in popular applications like the Toyota Avalon, Sienna, Highlander, Solara and Camry, as well as the Lexus ES300 and RX300. The engine in this video is from a 2003.5 Toyota Camry V6 with approximately 170,000km, in its latest revision with variable valve timing and a drive-by-wire throttle body, negating the presence of an EGR system.
In this teardown, we find the engine is comprised of a plastic intake manifold with an acoustic air induction system, metal valve covers, aluminum alloy heads, block and upper oil pan, in addition to the the stamped steel lower oil pan. It has dual overhead camshafts driven by a timing belt and variable valve timing on the intake side. The block has a semi-open deck design and cross-bolted main bearings for the crankshaft with two pairs of thrust bearings to ensure longevity, as well as a uniquely balanced crankshaft for smoothness. Some of the weaker spots on this engine included engine oil gelling due to an under-designed PCV system and long oil change intervals, valve cover leaks, faulty knock sensors and harnesses and a difficult to access power steering pump.
This is the Camera I use:
amzn.to/3oaRcZX (US)
amzn.to/3KWQ2uU (Canada)
Link to Etsy shop where you can purchase speedkar99's brother's socks, t-shirts or hoodies:
www.etsy.com/ca/shop/Speedkar
speedkar9 on Instagram and Tiktok
/ speedkar9
/ speedkar9
speedkar99 on Facebook and Linkedin:
/ speedkar9
/ speedkar99
Subscribe for more videos just like this:
kzfaq.info_...

Пікірлер: 685

@Ciruchan 2 жыл бұрын

Our family car was a 95/96 lexus es300 with this engine. We stopped driving it regularly after the issue with steering made it a road hazard. I pretty much ran this car to the ground when I drove it (I was a bad owner and let it run dry on oil 2 years ago). It still starts and runs today by some miracle. I plan on pulling & rebuilding the engine and transmission, repent for my sins, and see how many more miles I can run the original engine on. This video helped a lot, thank you

@speedkar99 2 жыл бұрын

May your sin be forgiven 😉

@dennisrobinson8008 7 ай бұрын

Suspension and steering rack will be worn out by 200k. Luckily it's pretty cheap to get a new steering rack and tire rod ends, new control arms and ball joints, and new front struts and shocks. It will tighten up your car to a "like new" feeling. I know when it's old and sloppy it can make you hate it, but it's cheap to correct.

@Ciruchan 7 ай бұрын

@@dennisrobinson8008 I just put in new tie rod ends, control arms, and steering rack bushings. I plan on replacing all my wheel bearings, putting in the new struts like you suggested, putting in a new steering rack, and redoing the brake & fuel lines (I live in rust belt).

@dennisrobinson8008 7 ай бұрын

Sounds good. My car was trash until i did it and afterwards it's a competent car. I also took care of paint and clearcoat so it has a good appearance.@@Ciruchan

@Tahara-Aichi 4 ай бұрын

3vze is the engine in the second gen.

@RexenPrime 2 жыл бұрын

It was a shame to see an engine that was so clean and in good condition being taken apart. On the other hand, it was refreshing to see an engine that had been taken care of so well.

@speedkar99 2 жыл бұрын

Yes it was very clean. It'll be rebuilt into a track car, don't worry

@oday3514 Жыл бұрын

I have this engine in my 2001 Avalon. Your video guided me through the timing belt, oil seal, timing belt tensioner and water pump replacement at 82K miles. The belt replacement went well except that I buggered a crankshaft oil seal - twice! Right now, I am at 112K miles, and the engine (and the car) runs perfectly.

@johnp9194 Жыл бұрын

Great review of a great engine. I just might have the highest mileage version of this one still on the road in my 2000 Solara...622,000 miles and still adding more daily. I picked the car up with 113,000 miles from a coworker so I'm the second owner. I checked the compression recently and it ranged between 400 and 415 psi...right where it should be. I checked valve clearance fairly recently and it was also in spec. Still gets 25 mpg and is still running the original transmission. Amazing engine!

@jonny-mj5jl 9 ай бұрын

you ever change the transmission fluid?

@dennisrobinson8008 7 ай бұрын

Crazy that it's on the original transmission.

@cambienvenu 7 ай бұрын

We’ve got a 2001 Rx300 with 230k, the suspension is about to get some TLC but the drivetrain is amazingly strong to this day. Not a single leak and transmission shifts perfectly. We did get lucky that the dealer had maintenance history up to 150k, then through 200k when we bought it, a friends mechanic father had taken good care of her.

@ojofelixnm3608 4 ай бұрын

400 psi compression reading, not in this universe.

@regal953 3 ай бұрын

I'm sure you meant compression is 200 to 215 psi, there's no gasoline that won't detonate under 400+ psi , unless it is a diesel..

@trendmassacre8423 Жыл бұрын

Nothing more satisfying than watching a good old fashion engine teardown while listening to the person doing the disassembling describe parts of said engine.

@gbudning Жыл бұрын

This is a phenomenal teardown video with clear explanations and no fluff. I will be showing it to my grade 8 students as part of our mechanical literacy unit. Thank you for this awesome resource!

@GeneFever 2 жыл бұрын

The 1MZ in my '97 Camry was a great engine. Changed oil myself regularly but had the dealer do the belt, pump and plugs around 150km. Ran it 'till 300km then moved on. I can't remember replacing any of the ancillary bits; alt, starter, rad, ps pump. Crazy good car all around.

@speedkar99 2 жыл бұрын

What happened to the Camry, sold it?

@GeneFever 2 жыл бұрын

@@speedkar99 Yes I sold it, back in 2013.

@Super6-Four 2 жыл бұрын

@@GeneFever Why did you end up selling it ? Just curious

@GeneFever 2 жыл бұрын

@@Super6-Four No reason really due to the car itself. It was my commuter for ten years then I retired and didn't need it anymore. I was ready to move on.

@richcityrepresentative8805 Жыл бұрын

Still have my 00 Solara with the 1MZ of 13 years.. bought it with 80k Miles currently have 223k and going.. I'm ready for an upgrade but I think I'm going to keep this car around as my daily commuter to work super reliable engine

@hayksamvelyan 2 жыл бұрын

Amazing engine, thanks for the tear down! I have an early version from 98 without VVTi, with the waste spark system, and cable operated throttle. It’s currently at 306k miles, with the first 170k being under someone else’s ownership and being very neglected when I got it. I loved seeing you describe all the common issues as it’s so familiar.

@speedkar99 2 жыл бұрын

You are welcome. I remember you from the club Lexus days. I am familiar with these motors from those experiences that's why this was a favorite for me as well.

@xuanzheng1049 2 жыл бұрын

This is the most legendary closed deck v6 engine ever made, and I have owned 2 vehicles with it, 94 and 05 Camry, both ran to 400 k km with 0 issues

@karolprzychodzki2662 2 жыл бұрын

Love my '99 V6 Camry sound. I care as much as I can. Now 380kkm - no leaks, no bunig oil. A/T works great. But it starts to rust :( Thanks for all informative videos.

@speedkar99 2 жыл бұрын

Keep it rustproofed and it'll last a while

@everydaychris5597 2 жыл бұрын

This is great! I literally just finished a lengthy timing belt/water pump/crank, cam seal with new plugs and oem coils on my mom-in-law’s ‘01 Avalon. They really are great engines.

@speedkar99 2 жыл бұрын

Nice!

@TheTomahawkTech Жыл бұрын

I know this video is old, but I see that you made the same mistake that I did, so maybe it will help someone. Before removing the exhaust cams, there is a procedure to install a service bolt in the sub gear, so that you don't lose the pre-loaded tension that is there to help with backlash. When this is not set properly, your engine will run fine, but will have valve train noise. It's actually the slop between cam gears. I just did both head gaskets on mine, and put it back together. It runs great, but is noisy. Now, I have to pull the valve covers and do this procedure to quiet it back down. Hope this helps someone.

@thall6594 2 жыл бұрын

I have a 1mzfe in my 2000 Avalon. It burnt an exhaust valve in cylinder 2 at 189k. I did a top end rebuild and replaced the valve along with a bunch of other parts and seals, and it's running perfectly again now at 217k. Great reliable engine, fairly easy to work on.

@speedkar99 2 жыл бұрын

Good for saving that motor. Cylinder 2 was the easier to access front bank right?

@naseerahmed6805 2 жыл бұрын

Mine did the same thing. Exact same car and I replaced it myself. Runs like a champ. Only 176k miles can’t wait to push it to 500k +

@aaronlamarr8456 Жыл бұрын

Have a 96 Avalon cylinder 2 blown spark plug heavy smoke out tailpipe what could be the problem?

@sjddjs 5 ай бұрын

That's my engine! 03 v6 Solara. Runs like a dream.

@speedkar99 5 ай бұрын

I miss my Solara.

@LamNguyen-hs2wo 2 ай бұрын

i have 2006 Solara 3.3l, about 207.000 miles. still running strong, always synthetic oil and toyota filter every 3,000 or 3,500 miles oil change. tuned up myself. reliable vehicle 👍

@groundzero_-lm4md 2 жыл бұрын

One thing all these engine teardowns have told me is that changing your oil regularly is very important.

@speedkar99 2 жыл бұрын

Agreed!

@joshuarivera428 Жыл бұрын

When I bought my 2000 avalon with the 1mzfe, it had no sludge. 3 years later it STILL has ZERO sludge. It's because I use full synthetic with MMO and factory toyota filters. Mostly the yzzd1 filter but when it's available I use the yzzd3 Oem filter. I change it every 5k miles and anytime something is wrong I fix it myself and always do the maintenance on time. I just did my valve cover gaskets, spark plugs, and tube seals. Did much more but don't want this comment to be too long lol. Put over 200k miles on the car with no issues. I'm almost at 300k miles.

@nigratruo 10 ай бұрын

BUT, what I learned: if you have a good engine, you can stretch the intervals and it won't be a problem. While if you have a garbage engine, you could change the oil every day and it will still break. There are tons of owners of cars made by GM that can attest to that. If oil was that important, pretty much any engine would last forever, as many people change the oil very frequently in fear of the car breaking (and everybody trying to make extra money off that FUD of "not changing your oil frequently enough" (like claiming that the new interval is now only 1000 miles ;-) Toyota builds these engines extremely sturdy, they use super tough alloys, I have so far owned 5 Toyotas and not one had considerable wear in the engine and I'm talking about a minimum of 300k km (150k miles).

@manxman8008 5 ай бұрын

and Filter ;)

@RickTroutner 2 жыл бұрын

I have an MZ in my 99' ES300. Since learning about its robustness I've put in the time to take care of it. I just did a timing belt/water pump job on it also replacing the cam and crank seals, I replaced the leaking power steering pump and pressure line which has pretty much stopped all of the leaks. I dealt with a burst coolant bypass hose last year where I replaced the knock sensors, fuel injector seals and the gaskets. Radiator hoses, Thermostat, radiator all replaced. Just finished putting some new spark plugs in it and I love how smooth it drives. A big shout-out to you and your channel which has given me the knowledge and confidence to even attempt alot of these repairs. The car has around 180k miles now I want to see how far I can take it. One of next repairs will be to attempt your AUX hack to connect my phone to the stereo which is the only feature I'd like to make it a modern car.

@speedkar99 2 жыл бұрын

Nice work! Keep it well maintained and it'll last. All the best on the aux hack, it's been a while since I've done that.

@nicks1169 2 жыл бұрын

Nice man. I have a 93 es300 with 193k right now. Just did spark plug wires and cap/rotor to clear up a misfire. Old fashion tune up and she runs amazing still

@thomasrush4550 Ай бұрын

Just use an FM radio transmitter that plugs into the cigarette lighter! Easy solve.

@Nathandm78 2 жыл бұрын

2003 RX300 Here! Thanks for the complete teardown! Love this engine!

@speedkar99 2 жыл бұрын

Awesome!! You are welcome

@barryf5479 2 жыл бұрын

I have a 2001 Toyota Solara V6 and it's a great engine. On mine, the oil filter is in the front which makes it a lot easier. I'm about to turn 280,000 miles on it. So far, all I do is oil changes every 3 to 5,000 miles on it (if I'm mostly freeway miles, it's 5,000 miles) and change the spark plugs, timing belt and water pump every 100,000 miles. My only other items replaced were brake pads and one time, the O2 sensor and the rear valve cover gasket was barely leaking but I could smell it on the exhaust manifold so it was replaced. The car doesn't burn or leak any oil other than the one time with the valve cover gasket. The transmission has been holding up fine. This car may outlast me and I have no reason to replace it as it continues to be as reliable as it was when it was new.

@speedkar99 2 жыл бұрын

I miss my 99 Solara. All MZ engines had the oil filter in the same spot under the exhaust manifold.

@TangoMike88 2 жыл бұрын

So happy to see this video! Just in the last month I bought a 230k mile 1996 Camry with this motor in it. I've been reading about it and preparing to do quite a bit of touching up to counter some of the neglect, but what amazing timing! So far it's an amazing car, even with it's issues. I can see myself having it for quite a while. Makes me proud to have it with that title!

@jonathanhamilton6554 Жыл бұрын

Great engine have 422k miles on my 02i and aside from the catalytic converters I just recently popped a code for a knock sensor that keeps it from going into overdrive. This motor is the best part of the entire car.

@daneish96 2 жыл бұрын

Been happy with my 98 Camry for the past 10 years. I’ve replaced my valve cover gaskets once, I can also attest to power steering pump being a pain to access haha. Around 230,000 miles and never had any real issues, overall great motor👍

@jcl197 Жыл бұрын

Just one comment that might help some people out, you don't need to remove the intake manifold to change the rear spark plugs, they can be changed with the manifold in place. I have been doing it that way on my 1mz-fe for years.

@richcityrepresentative8805 Жыл бұрын

I do as well.. 2 from the passenger side and one from the driver's side

@DevJB Жыл бұрын

One of my estimator tools says 600 to 750 for spark plugs, I can do them on this engine in about 20 minutes.

@johnkaranja2897 2 жыл бұрын

I have same engine in a 2000 Avalon, 294,000 miles. Drives like a dream. I change oil at 3000 miles or 5 months, whichever comes first. I wish I was as good as you are. I would take it all apart, clean, and rebuild. Good video.

@speedkar99 2 жыл бұрын

Beautiful, almost 300K

@Laphoot 2 жыл бұрын

my 22 yr old Lexus ES has it, with 195k on the clock. Still running strong. It's more reliable than most of the modern cars nowadays.

@speedkar99 2 жыл бұрын

Loved the 3rd gen ES!

@mscir 2 жыл бұрын

The knock sensor rap was interesting, and the cutoff beep was still funny. This looks like a really well designed engine.

@speedkar99 2 жыл бұрын

Yeah it was just my brother blabbering on about the electronics behind knock sensors. Had to edit it down quite a bit

@mbox314 2 жыл бұрын

The explanation on how the knock sensor works is great! Thanks for including that.

@speedkar99 2 жыл бұрын

Glad my brothers explaination helped

@davidbragg30 2 жыл бұрын

I’ve had mine for 12 years. Never had any engine issues just keeping up with the maintenance. So reliable..

@speedkar99 2 жыл бұрын

Awesome! What car is it in?

@davidbragg30 2 жыл бұрын

@@speedkar99 2005 Avalon. 3.0 V6 in Australia.

@LOLZZ184 2 жыл бұрын

I'm a Toyota apprentice :) and recently got me a Toyota Highlander with this engine! learnt a lot of theory, now it is time to put it into action! Going to replace valve cover gaskets, timing belt, water pump, transmission filter, and rear brake caliper. Wish me luck!

@speedkar99 2 жыл бұрын

All the best. I have videos for all of those to help you out

@HyproTube 2 жыл бұрын

Love your videos! I always learn something. Especially enjoyed your brother's cameo explaining how knock sensors work 💯

@speedkar99 2 жыл бұрын

Glad you appreciate it. It was more of a joke between us, he happened to walk up with I unbolted the sensor and started nerd out on me on how it works haha

@qj8933 23 күн бұрын

My 97 Lexus ES 300 with the same engine now has 356,000 miles and going super strong. Ive done all the maintenance myself except for oil changes which I leave to oil lube places every 3k miles. Run conventional 5w-30 oil. So far Ive changed the timing belt, water pump, tensioner, etc about 3 times, replaced the 2 of the transmission solenoids, occasional belts and hoses when needed and run Iridium denso spark plugs. Actually just replaced the rear control arms for the 2nd time on this car yesterday. Only just replaced the entire exhaust system with a Walker one last year ...no CEL, runs and drives fast and smooth. It sounds like a lot of work and money but this car owes me nothing, best engine/car Ive ever had for reliability. Had it since 2012, bought from a car auction when it had 134,000 miles on it. Ive had the valve covers off a few times and no sludge issues. My 99 Lexus ES 300 with 101,000 had the sludge badly when I bought from a private seller who was running oil with no detergent but I cleaned it out, replaced the valve seals and hope to run it just as long as my 97. They dont make them like this anymore, now its all planned obsolescence.

@speedkar99 23 күн бұрын

How's that exhaust holding up? I know someone who has and it's rusting away already

@qj8933 18 күн бұрын

My OEM exhaust lasted up until about 2020 then I had to start cutting out the damaged flex portion in the Y pipe and welding in new flex pipes which doesnt last. I replaced the entire exhaust with a Walker system I think. It was from rockauto and painted black. That was about a year ago and its great so far. No rust, no CEL codes.

@janet53589 2 жыл бұрын

Just completed a round trip Texas to California in a 1995 Camry V6 1MZ. Went sailing past many a Tesla at 30 mph faster than them on i40 and used a range of 420 miles between fuel stops. Had the valve clearances done earlier and also a new timing belt kit. Engine seems as good as new. 207k miles so far. Smooth and powerful, the best engineering. Sets the standard for durability.

@janet53589 2 жыл бұрын

0-60 of around 7.6 seconds, top speed of around 138 mph, power of 189hp, torque 203 lb/ft, the car is not short of power btw.

@02SLERA 21 күн бұрын

Took my 02’ Solara on a round trip from Texas to San Diego to Monterrey, to Las Vegas to Albuquerque then back to Texas a few years ago. I had the car inspected and topped off before the trip and I never had a worry.

@janet53589 20 күн бұрын

@@02SLERA Smart move to get an inspection prior. It can revel many an issue, much easier to fix beforehand than by the roadside! PS. Do keep the gearbox oil changed and fresh.

@02SLERA 20 күн бұрын

@@janet53589 Thanks for the advice, I don’t think I’ve ever had that done!

@janet53589 19 күн бұрын

@@02SLERA I should have mentioned, that Toyota gearboxes can use either combined gearbox and differential oil, or they can be separate. If it is separate, then both the gearbox and also the differential oils should be changed separately. It is easy to overlook this fact, if your car is one of those using the separated arrangement. You can do the job yourself if you want, just use fully synthetic ATF.

@mrsargemeister 2 жыл бұрын

Nice teardown. Brings back memories. My parents had a 96 Avalon with the 3.0 1mzfe. Cable throttle, no vvti, and only 1 set of coil packs on the front bank. This means it was a waste spark design. I guess the advantage is fewer coil packs that could potentially go bad in a very hard to reach spot. Very smooth and refined engine. Exhaust tuned to be whisper quiet. In those days that was what you wanted. It did have valve cover leaks later on. We never addressed that. I believe it was rated somewhere at 195-200 hp which in those days was considered a lot. Even though the avalon was a heavy car it had lots of pep. We never had sludge problems because in those days we always changed the oil every 3k miles. The one thing that always scared me was what it looked like under the oil fill cap. You showed that in your teardown and it wasnt pretty. Little did I know it was probably spotless. I'm amazed at how stout the bottom end is in your teardown. Looks absolutely bulletproof.

@mrsargemeister 2 жыл бұрын

One thing I forgot to mention was that I burned my forearms more then once changing the oil filter. Not a great location as you mentioned.

@speedkar99 2 жыл бұрын

Good story. So what happened to the Avalon??

@mrsargemeister 2 жыл бұрын

@@speedkar99 pretty undramatic ending. They sold it in '09 when I found them a great deal on a used 2006 es350 which they still have. The avalon was good to them. The only major problem it had was a leaking power steering rack that my dad replaced.

@SamslamminCars 2 жыл бұрын

I just did a timing belt and seal overhaul on my moms 03 Avalon with this engine and 280k miles. That vehicle is a true testament to Toyota’s older reliability. What a pain to do over my Accord J30 engine in the bay.

@speedkar99 2 жыл бұрын

280k miles, nice! The accords were good motors too, the only thing I appreciate about them is it's easier to get to the rear spark plugs due to the intake design

@SamslamminCars 2 жыл бұрын

@@speedkar99 I have done at least 30 T-belts for the J-Series and already 2 too many now for the 1MZ-fe. She runs 87 octane in it and supped to be premium but still runs perfectly smooth with no hesitation. I settled on a 06-6-6 sedan. Accessories are not as reliable on a Honda but those engines really are bliss.

@thetechlibrarian 2 жыл бұрын

I miss by accord with the j30 v6

@SamslamminCars 2 жыл бұрын

@@thetechlibrarian my friend is selling one for around 2-3k Virginia.

@nima20031 2 жыл бұрын

My favorite engine. Mine is going strong at 175k miles. I've learned so much about cars by working on it.

@speedkar99 2 жыл бұрын

Awesome

@lilm777 2 жыл бұрын

What a throwback...I subscribed when I had my Solara and found your videos....

@speedkar99 2 жыл бұрын

Awesome!

@michaelrads1365 3 ай бұрын

Thank You. Detail is Meaningless without Context. Your meaning is ULTIMATE. THANK YOU

@speedkar99 3 ай бұрын

Wow, thank you!

@TheGonso35 2 жыл бұрын

I have this same engine since 2002 with 130,000 miles. Very reliable, smooth with ok power and fuel efficiency for today's standards. In the last 20 years I had to replace one knock sensor, 2 oxygen sensors, spark plugs, timing belt and water pump. That is it. I tightened the valve cover bolts to stop oil seepage in the winter months. I know I will never own an engine this well made.

@speedkar99 2 жыл бұрын

Nice! How's the fuel economy on yours? I know it's a V6 but my Lexus GS350's V6 makes more power and has better fuel economy than my Camry's.

@id.747 2 жыл бұрын

Awesome video! Thanks for showing this tear down! I have one of these in my 2000 RX300 with 290,000mi. It runs just as well now as it did when it was bought with 50,000mi! Keep up the great work :)

@speedkar99 2 жыл бұрын

Nice! Keep it maintained and it should last a while

@Coach_cesar 2 жыл бұрын

Currently whip a 95 camry v6, car is running strong! Odometer currently at 276k miles

@speedkar99 2 жыл бұрын

Awesome!!

@nadirkhan7552 Жыл бұрын

Just bought a Toyota Harrier Airs 2003/09 model with 1Mz-FE 3000cc V6. This video helps a lot. Changing timing belt and checking all leaks and new oils 🛢 Thanks for the 📹

@bonjournaste 2 жыл бұрын

Love it! Miss MZ engine in old Sienna vs 2GR-FKS in new one.. Way more power in new one, but old one was so much smoother, and sounded great.

@speedkar99 2 жыл бұрын

Agreed. 2GR has good power, I have the 2GR-FSE version in my GS350 and I enjoy it, however at the expense of Lexus smoothness you'd expect

@NachoChurro 2 жыл бұрын

There was an old video of a 2gr swapped red MR2. I'm not sure who did the swap, but it sounded awesome. Like an older baby ferrari v12. I have yet to find a similar swap with the same intake and exhaust noise, though. Big fan of sleeper builds using the 1mz engine.

@JasonLuther1 2 жыл бұрын

You're the man! great teardown and knowledge packed information

@speedkar99 2 жыл бұрын

Thanks!! Please share with your network

@foreststarr6879 2 жыл бұрын

My 2000 Camry V6 has a well-preserved, 92,000 mile engine. With this video, I have more of an understanding of those late 90's, early 2000's "Golden Age" era engines built with that expected Toyota quality.

@speedkar99 2 жыл бұрын

Nice, only 92K

@foreststarr6879 2 жыл бұрын

@@speedkar99 Would you have an opinion on what is the preferred gasoline for the 3.0L V6 1MZ-FE? My 2000 Camry manufacturer's manual says: "1MZ−FE engine: Unleaded gasoline, Octane Rating 87 (Research Octane Number 91) or higher. For improved vehicle performance, the use of premium unleaded gasoline with an Octane Rating of 91(Research Octane Number 96) or higher is recommended." Is "premium unleaded" preferred? Thanks.

@noble20xx56 2 жыл бұрын

Bro respect for posting this. I got an 01 Lexus ES. Same car pretty much. It's great to see an in depth look at the stuff you own.

@speedkar99 2 жыл бұрын

Yep very similar engine. How's yours running?

@noble20xx56 11 ай бұрын

@@speedkar99 KZfaq sucks lol. Still a smooth chill ride as ever. I don't plan on selling any time soon lol.

@Faitzer 2 жыл бұрын

I learn so much with every video, the way you explain everything makes it really entertaining for me, thank you

@speedkar99 2 жыл бұрын

I'm glad you appreciate my videos

@roltyd22 Жыл бұрын

Ive got a 3.0 in my 03 Avalon XLS..170k miles runs great...great video!!

@Bazzer1955 Жыл бұрын

I am sure we have this engine in our Toyota Alphard 3.0, imported from Japan. So far it has been silky smooth and pulls like a train. It has only 72,000 miles on it, cam belt was changed in March this year, oil was changed 3,000 miles ago and it starts on the button. Great videos not time waster videos, straight and to the point. Subscribed. Well Done Sir

@sharikharib 2 жыл бұрын

My man Nice detailed work as usual Dont forget about trouble shooting and maintenance tips for us Thanks!

@speedkar99 2 жыл бұрын

Good idea. I will be showing how to fix up and sell a car in the next video.

@02SLERA 21 күн бұрын

02’ Solara with 205k and I plan to keep it forever. Not sure how much of this video I will make use of but I love it. Thanks!

@michaelrads1365 3 ай бұрын

Thanks mate. Great DEPTH and ANALYSIS, everything I wanted to learn , I bought a car/vehicle with that engine. I am excessively satisfied and YOU HELPED

@speedkar99 3 ай бұрын

Glad it helped!

@antoniowade3318 2 жыл бұрын

You guys ain't know joke, really spot on. Outstanding video.. Wade Out..

@Shunpall Жыл бұрын

Found this video very informative and engaging.. I still own one of these and do not plan on letting go anytime soon.

@eroticmasterbaker Жыл бұрын

I Have a 99 Sienna with this motor with 182000 miles. I over torqued the water pump bolts too by using ft pounds. Only stripped one bolt though. I replaced the leaking valve cover gasket on front cylinders. It still leaks a little on back. Engine runs great!

@user-ts4ym4mv5l 3 ай бұрын

Excellent Vid. I learned a lot.

@user-kb7zl2ji5c 2 жыл бұрын

Delighted to watch this video. Well done

@speedkar99 2 жыл бұрын

Thanks

@deloreanman14 5 ай бұрын

I just picked up a 1994 Camry with this engine with the cable throttle, metal manifold and no VVT-i and while it's definitely a lazy engine that would prefer to loaf around between idle and 3000 rpm instead of revving out, I have been amazed by its smoothness. The car only has 117,000 miles on it and there's a lot of evidence that it sat for a long time in somebody's garage but that's not to say it's been neglected as the radiator, valve cover gaskets, fuel filter and timing belt are all brand new. I have noticed the coolant overflow tank was nearly dry when I got it and after topping it up (not filling it all the way) a couple times, I think the system is now at level, just above 'low' when cold. This leads me to believe whoever did the radiator didn't fill it all the way. Thanks for this video!

@michaeldunagan8268 4 ай бұрын

That's funny- -the 1mzfe in my 1999 Toyota Solara doesn't start making power until 3,000 RPM. It makes power all the way to the red-line. Something isn't right with your car. Might have a restricted exhaust or something.

@skyscraper37 2 жыл бұрын

I could watch these videos all day long!

@speedkar99 2 жыл бұрын

Thanks! I have many engine teardown

@TylerSchappe 2 жыл бұрын

When my wife and I met, I had a 2000 Camry with a 1MZ and she had a 2004 ES330 with the 3MZ, both inherited from our families. For a couple of years they lived side-by-side in our garage until we needed a bigger car for our first kid and I sold the Camry. We still have the ES with 151k but it needs the cam seals replaced and then I think it’ll go for another 100k miles easy. I actually think the 3MZ feels a little smoother among the two. Great engines and excellent video!

@joeboggan Жыл бұрын

I have that motor in my 95 Camry Wagon, so far so good. I will need to replace some seals soon but no big worry. Thank you for sharing

@livetoinspireall2755 10 ай бұрын

Tightening those valve cover bolts and replacing that water hose and O-rings! THANKS Speedkar99

@hopefultraveller1 Жыл бұрын

Thank you for this excellent video, which explains so much of why this engine is so great. I have a 1999 JDM Toyota Harrier 3.0 Four (4WD) with the excellent 3-litre 1MZ-FE with dual alloy inlet venturi and drive by wire throttle body. It's done 145,000 miles and - with the help of a custom exhaust with equal-length downpipes - makes lots of smooth torque and has an amazing sound! It has great throttle response and really takes off when the VVT-I kicks in. There are a few spec differences to the same engine as used in the Lexus RX300, including shorter intervals for changing the cam belt, and higher power output of 225BHP on 97 octane fuel. Also being pre-OBDII, it has more flexibility on tuning and gearbox integration, such as a manual mode with steering wheel gear change buttons, and the ability for the torque converter lock-up to vary more than OBDII cars. I drove the plastic inlet 3.3-litre version (3MZ-FE) and found it sluggish and unresponsive in comparison. I fall in love with my car every time I drive it, I've upgraded to the 2003-on 18-inch wheels, which work well with the all-independent suspension for a smooth and very composed ride. It's nearly 24 years old but is such a good drive that I can't even contemplate driving anything else. The 1MZ-FE is definitely the strong heart of the car, and - excepting a few design weaknesses like the ABS sensors - everything else compliments it very well. Its only Achilles heel is fuel economy - I can't get more than 19 MPG (UK) from it, but it's totally worth it!

@Animalhouser Жыл бұрын

Thank you for the tear down. I have this engine in my rx300

@speedkar99 Жыл бұрын

Cool!

@twl107 Жыл бұрын

Awesome video!

@thabitpulak 2 жыл бұрын

Such a great video!! No one on the web does these tear downs and explanations better. Next time, can you please make a video on the 3mzfe? And comment on the differences and similarities as compared to the 1mzfe? Lots of these engines still on the road, like the one in my 2nd Gen Solara!

@speedkar99 2 жыл бұрын

You are welcome. I'll do a 3MZ if I ever get one but as you say most are still on the road.

@Adam-kb2mn Жыл бұрын

Good info.Ive watched this video a few times now since I have now got one of these.

@CanielDonrad 2 жыл бұрын

Those xv20 camry were so unbelievably good

@speedkar99 2 жыл бұрын

The xv30's V6 was good too. Not so much the 4 banger

@Dansk55 2 жыл бұрын

Wow good stuff as always. Seems like a knock sensor is a really senstive microphone. This engine's been good in our non-interference rx300. No issues so far at 155k miles except rust lol.

@speedkar99 2 жыл бұрын

Yes the knock sensor is a microphone that's tuned to detect certain frequencies. Gotta keep the rust at bay by frequently Washing off salt and rustproof each year.

@brandonosborne6894 2 жыл бұрын

My family has multiples of these engines from different years. 1 and 3mz. Great engines.

@speedkar99 2 жыл бұрын

Good engines indeed. Keep the oil changed on the older ones to avoid sludge

@jonnyduncan7056 2 жыл бұрын

Very informative as always.

@speedkar99 2 жыл бұрын

Thanks

@drgntmrutugmr5560 Жыл бұрын

Wow nice detail about tear down most reliable 1mzfe engine.

@manxman8008 5 ай бұрын

I just bought a Lexus RX300 2006 with a 3 litre v6, 120,000km. Very smooth and powerful. Took it to 180km, nice. Pulls well uphills. Good transmission. Thanks for showing how well-designed/made it is - especially compared to a complex under-engineered Audi.

@speedkar99 5 ай бұрын

RX330 are good reliable cars, if the rust and AwD powertrain don't catch upto them. I have the 3.3L engine in my Camry and it runs smooth.

@brandondavis9096 11 ай бұрын

I’ve got a 97 Avalon with the 1MZ FE and I love this engine

@tonyaulet7220 2 жыл бұрын

Got one in my 01 es300. 192,000 runs smooth and quiet as the day it was made. Love these motors

@speedkar99 2 жыл бұрын

Beautiful! Just watch out for the transmission in those 99-01 ES300s

@tonyaulet7220 2 жыл бұрын

@@speedkar99 already replaced it. Torque converter went out

@rjcontruction1406 2 жыл бұрын

As always great teardown vid, wish it was always as easy to work on as it was when you have it out of the car.

@speedkar99 2 жыл бұрын

Agreed. It's not easy on any transverse V6

@freedomnetworth5243 Жыл бұрын

Love the 1mz-fe community

@regal953 3 ай бұрын

Thanks for this video, I have just purchased a 2000 Solara SE equipped with this engine and a 5-speed manual transmission with 214.000 miles on it, hoping to make it go to 500k...

@speedkar99 3 ай бұрын

I miss my old Solara

@02SLERA 21 күн бұрын

How’s the Solara doing?

@CHARLYNNE123 Жыл бұрын

Great video

@ksd9756 2 ай бұрын

I had this engine on my Australian built 2006 3.0 V6 Camry and I can honestly say its the most reliable car I've ever driven. I had it for 15 years until last week.

@speedkar99 2 ай бұрын

Nice. I have the 3.3L Camry and it's running strong.

@jackwigley37 7 ай бұрын

Great video, you did a fatastic job of explaining everything and I learnt a lot! These engines are a popular swap into the mk2 mr2 in the UK, instant torque at low RPMs and consistent powerband thourgh all rpms works well on our cars, other Toyota engines like the 3mz, 3vz and notably the 2grfe are popular engine swaps into the mr2 as well. I would like to put in a 1mz at some point in the future, very cost effective and it is pretty simple as far as engine swaps go. This teardown helped me understand what makes this engine so popular!

@2hambonemcgee 4 ай бұрын

Just bought a 2000 es300, runs really good! 104k miles. It's nice and clean inside the motor and I plan to keep it that way! Thanks for the informative video, I subscribed!

@speedkar99 4 ай бұрын

They're great cars. Watch the transmission on the 99-01 ES

@williamkreth Жыл бұрын

Great breakdown video! I have a love hate relationship with the 1MZ. It's very reliable, very powerful, but I lost one due to engine sludge. I bought a used lexus and switched it over to synthetic oil, it loosened up a bunch of sludge which ended up completely blocking the oil pickup tube starving the motor of oil! Idk why the low oil pressure light never came on. just stalled out, and had metal shavings in the oil and rod knock. there was smoke coming out of the oil fill hole when I opened it. I put a used motor into the lexus put full synthetic in it, but going to only drive it 1000 miles then drop the oil pan and check the oil pickup tube. Not losing this motor to that.

@richlikeg3722 2 жыл бұрын

Ah been waiting for this one.

@speedkar99 2 жыл бұрын

Yep it's been winter and finally had a brink of spring to film this

@user-ij1jj2df2b 5 ай бұрын

great video to know about this engine

@speedkar99 5 ай бұрын

Glad you liked it!

@oldergeologist Жыл бұрын

Great commentary.

@mapleshaft 2 жыл бұрын

I love the story about your f'up on overtightening the idler pulley. I was feeling down on myself for a big oops i made and it reminds me that even expert professionals like yourself make mistakes from time to time.

@speedkar99 2 жыл бұрын

Yes. That was 10 years ago when I was just starting to work on (real) cars and not just bicycles and computers

@freezee7547 2 жыл бұрын

Nice practical review ever!

@speedkar99 2 жыл бұрын

Awesome thanks

@freezee7547 2 жыл бұрын

@@speedkar99 Yeah, man. Your the best!

@bujin5455 Жыл бұрын

Looking forward to you doing a 2GR-FE!

@moddie1309 2 жыл бұрын

Excellent video. I have three 1MZ-FE's - in a '98 ES300 (242k mi), another '98 ES300 (210k mi) and '00 Sienna (180k mi). I have learned a lot by watching your videos and think you should also sell your brothers toothbrush in the Etsy store. All run well (even though the body on one of the ES's leaves something to be desired) and I have no plans of selling any of them. Taking the Sienna on a 2k mile road trip next month! Keep up the great work. I do all of the work myself thanks to your videos!

@speedkar99 2 жыл бұрын

Nice! I like my old Toyota Lexus too

@jonathangrubmeyer9104 2 жыл бұрын

Thanks for this video.

@speedkar99 2 жыл бұрын

Welcome

@Timrh23 Жыл бұрын

Still have my 2001 Highlander that I bought new. 270k miles. The valves tap pretty loud but only at idle. Smooth and quiet at acceleration.

@DIYLifeSkills Жыл бұрын

amazing tear down in 20 minutes.

@emangee9268 Жыл бұрын

4:00 "So as you can see there are two lines that go to this throttle body because this throttle body is pretty cool" 👍😎

@dinhscot Жыл бұрын

That Engine is Clean! Amazing how well kept the owner love his Toyota... Sad to see a perfectly good engine go this way

@zseavers1573 Жыл бұрын

I am currently driving a 2003 Avalon with 310,000+. I would like to rebuild the engine one day, thank you for the helpful information!

@marcosguardia2225 2 жыл бұрын

Speed, could you do a video of a 3.0 Duratec V6? Love that engine, also great content as always.

@mr.mg428mm2 2 жыл бұрын

The 3 plugs in the backside of the engine are easy to remove with ratchet extensions and wobble joints, without removing the intake.

@lanbolyra Жыл бұрын

Camry 2005 is my first car in Australia, it has 240000 km now. It’s so quiet and smooth on highway. Such a stressless car.

@speedkar99 Жыл бұрын

4 cylinder or V6?

@lanbolyra Жыл бұрын

@@speedkar99 3.0L V6 4sp Auto. It has the original head unit that can play cassette tapes, feels like a time machine🤣

@tylerwomelduff5335 4 ай бұрын

good to find out some stuff on this video thanks much

@speedkar99 4 ай бұрын

No problem!

@squishy312 Жыл бұрын

I have 2 of these engines. Well 1 now, my daughter has my old one. Mine is a 2000 Lexus RX300, and the other is a 99 Camry. Both have been excellent and amazing engines. The Lexus grenaded it's transmission shortly after purchasing (for a really cheap price). But, thanks to Rona money, I was able to rebuild the transmission and correct the defective first gear planet pins by welding them in. It works great now. The U140 Is a known issue that should have been a recall, but usually happened after warranty time. I just replaced the thermostat, as it was only getting to 165 max. It was an easy fix. Used OEM parts, which are a tad bit more expensive, but worth it, because it lasted this long already.