Hinges part 1: How to solder successfully

Рет қаралды 27,023

6 жыл бұрын

How to solder on hinges: used 2.5mm OD heavy walled tubing. Make sure your edges are FLAT. UPDATE: One thing that was brought to my attention that should be changed: make your center hinge longer and the outer top and bottom hinges about 1/4-1/5 the size of the middle one. The center hinge needs to support most of the weight and it is more prone to twisting on you! (Courtesy Brad Smith!)

Пікірлер: 33

@robertapihl76 6 жыл бұрын

Brad Smith has mentioned one thing I really should have done: make your center hinge longer and the outer ones about 1/4-1/5 the size of it. He said the center hinge takes nose of the weight and twisting and needs to be stronger!

@sandrafelisamunozbravo2921 10 ай бұрын

Good Reacher. Congratulations

@cuptonmillerlpnful 5 жыл бұрын

Thanks Roberta for the demo. Your method makes perfect sense. Ive never done hinges, but hope to try this method out soon.

@jimbettridge3123 6 жыл бұрын

Well done Roberta, never did hinges but would do this method for sure!

@annh3599 6 жыл бұрын

Thanks Berta! Very informative video! I like & understand your common sense methods! The end result of this piece is gorgeous by the way!💕

@shelleythompson8816 Жыл бұрын

Thank you for this set of videos, I've been wanting to learn this for forever!!!

@kizzywitch 4 жыл бұрын

Brilliant explanation....was alway put off doing hinges, thank you for this demo x

@CocomelloArt 3 жыл бұрын

Thank you! This was a very informative video, I can't wait to try out new techniques!!

@katiejo1095 7 ай бұрын

Great technique.

@klondyguerra 2 жыл бұрын

Thank you so much for sharing your experience and knowledge, it really helps :) and your work is lovely,

@bradsmith7147 6 жыл бұрын

Nice technique and demo. Thanks

@robertapihl76 6 жыл бұрын

Brad Smith ah and I appreciated you bringing up that center hinge! I’ll edit the description!

@Nancy4133nope 5 жыл бұрын

Excellent video thank you so much

@TravelingOurBestLife 6 жыл бұрын

Good job!!!

@mikema9311 4 жыл бұрын

Wonderful -thanks

@ruthdederich3622 2 жыл бұрын

Hinges!!! Thanks.

@debevanderheide5953 5 жыл бұрын

Great videos. How did you make the clasp for this one?

@soniaborni7402 2 жыл бұрын

Thanks

@kitschnsink 4 жыл бұрын

Could you please tell me which torch you're referring to when you say "ambient air torch"?

@pippinhillhaviland1147 3 жыл бұрын

What is the reason for the copper under the hinges plackets?

@suzzanarinaldi6207 3 жыл бұрын

what size wire and what size tube that go together?

@flyingcheff 3 жыл бұрын

When you say "hinges" do you mean knuckles? Isn't the hinge the entire thing? Thank you. I like the whole preheat of the flux, cool, it's like pre-glue.

@nandhines209 2 жыл бұрын

canI i know name of the flame gun and buying link

@huskyfluffy 6 жыл бұрын

And you said, after pointing our the tick, something about “one of Jim’s tools”. What tool?

@TLAS 5 жыл бұрын

Probably the bezel tool that you can find here: www.etsy.com/shop/HorseshoeEngraver

@ocmom7831 2 жыл бұрын

Hi Roberta...I have been following LKV and have been contemplating on taking a few of her classes....but can't decide which ones. Do you have any recommendations?

@robertapihl76 2 жыл бұрын

Any one of her classes can be found elsewhere and it’ll save you a lot of money. I’d never send anyone to LKV again lol The lockets can be learned from Alan revere for example, since it’s essentially his original work that has been personalized in her classes along with other tutorials he’s published. Alan has a book called “professional jewelry making,” and he runs a support group on Facebook for people who own the book and need a little help. He also does challenges and awards certificates of completion for people who complete certain sections. Melissa Muir helps run that group and between the two of them they make a FABULOUS pair to learn from! Alan is known among jewelers as “The Master of Masters” and for good reason. Multiple nationally recognized awards, previously ran a school for jewelers, has HIGH standards and is just as exceptionally encouraging as he is skilled. The book is $100 (I’m sure you can find a used one for less) and the support group is free. Beats paying $200 and not be able to keep any of the resources or videos.

@ocmom7831 2 жыл бұрын

@@robertapihl76 Thanks for that! Good stuff!! I have watched Melissa's videos as well on her journey with the Alan Revere projects. Will definitely buy his book! In all candor...I get a lot more from your video's more so than Melissa's. I soooo wish you lived in So Cal to offer classes. Your work is GORGEOUS! Thanks again!

@robertapihl76 2 жыл бұрын

Ah thanks darlin! I feel like Melissa is SO much more talented than I’ll ever be though! She has a beautiful eye for design and she teaches much better than I do I feel! I do worry some of my videos are out of date, and one day I’ll have more time to go in and show some new solutions to projects like these hinges I’ve learned over the last few years since I made this one. Next time I make a hinge project I’ll post an updated video! And that book is WELL worth every cent of it. And if you have any questions the Let’s Make Professional Jewelry FB group is where to go! Also Jinx McGrath has a great book that shows how to solder hinges and it has some great illustrations. There’s more than one way to do everything , and trying it all at least once will help you determine what technique you’re comfortable with using 💕

@huskyfluffy 6 жыл бұрын

Hi, do you not have to flatten the edge of the tube for better contact?

@robertapihl76 6 жыл бұрын

huskyfluffy great question! It does help yes, but I’ve found that it’s a bit of a pain to get the tube orientated properly and between the solder and the 18g sheet I’m using, it’s still going to have good contact ;) if you’re all right with fiddling a bit more I recommend it though ;)

@Frigger20 Жыл бұрын

I think I read in Alan Revere’s book and saw on video On the Bench that one needs to file a groove in the adjoining pieces rather than saw a flat on the tube.