home decorating - cheap print to expensive masterpiece!

No video

home decorating - cheap print to expensive masterpiece!

Рет қаралды 11,091

Күн бұрын

With the help of www.ArtResin.com, Sarah Walker from @thecuratedhouse used some non yellowing, no VOC epoxy resin to turn a standard stretched print into a shiny, expensive looking focal point for her 2015 one room challenge!

Пікірлер: 20

@DiodePress 8 жыл бұрын

Looks like a very cool product. The low odor is what really interests me! I might have to give it a try on some future projects!

@Artresin 8 жыл бұрын

+Diode Press great :) yes you may have to give it a try! :P black friday sales today!

@AngelasMixedMediaArtist 6 жыл бұрын

Thx love that it doesn’t yellow ❤️👍🏻

@jasonmitchell2012 6 жыл бұрын

Looks like a great product but so much more expensive than other similar products on the market.

@shelleydavid3896 6 жыл бұрын

Thankyou👍🏼

@victorhe7200 7 жыл бұрын

that's so lovely. I can't wait to begin my print. I have a question though, what kind of frame support is that for mounting the print?

@leonarddenning4202 5 жыл бұрын

Was this a wooden canvas or just a regular canvas

@williamsivy 7 жыл бұрын

I added a 2nd layer and had splotchy patches. I want to add a 3rd layer to correct. what do I do?

@aleksandercok8482 7 жыл бұрын

Good job, but how to clean tools after use?

@Artresin 7 жыл бұрын

wipe off with paper towel and let dry on the worktable :)

@TVBASICINFO 7 жыл бұрын

Rebekkas eyes freaked me out,,,, daaaaammnnn..!!

@curbsidenation 6 жыл бұрын

Well aren't you rude! Show a picture of yourself and we'll judge you?

@MiqueProjects 8 жыл бұрын

I need help... please give me a hand. I got as a gift some polyester resin (didn't know about Artresin) and I did some coasters and magnets in moulds, etc... The thing is that after cured they got a lot of fingerprints on them, and even though they go by polishing them, after I finish they get new ones and the circle never ends. Can you help me with a tip to avoid and stop this please? Many thanks

@Artresin 8 жыл бұрын

+Mique Films did it fully cure and dry hard? are they just std fingerprints like on glass? polyester resin is best for thick pours and is also pretty dangerous and stinky! maybe spray a top coat of a glossy varnish - wont look the same but may help stop the from happening. even sand the surface down a bit and apply a varnish...

@MiqueProjects 8 жыл бұрын

+ArtResin Hi again. I just tried art resin for the first time (after the disaster with polyester epoxy) but I had some issues and I wonder if you can give me some advice. First of all, after mixing the resin and hardener, it ended up being very white, full of tiny bubbles that were very difficult to get rid of. I used the resin to dome a little art work sample, and after a few minutes applying fire with a kitchen torch they went away... and even though it looked clear, when cured there still were a few very tiny bubbles in some places. I also used it to make some samples on a mold, but in there it was impossible to get rid of the bubbles... I only managed to clear the surface on risk of burning the mold, but underneath there were still a cluster of bubbles that made the piece look very blurry.... I wonder if you have any tips to avoid that huge amount of bubbles... maybe a specific temperature or something like that. Also, I noticed that the molded samples, and some leftovers from the doming tray, are quite flexible, kind of rubber like more than plastic... is that normal? Many thanks in advance for your time.

@Artresin 8 жыл бұрын

+Mique Films hmm. maybe sand the top a bit and spray on a top coat of a varnish? polyester resin is very dangerous stuff!

@MiqueProjects 8 жыл бұрын

+ArtResin hi. thanks but this was a different question about Art Resin

@Artresin 8 жыл бұрын

+Mique Films they will harden after 3 days! we have a longer full cure time then other material because this means better performance for long term non yellowing. if the resin is cloudy, you room may be too cold. try heating everything up first! bubbles MAY keep coming because it is reacting with something on the mold or something else you put in the resin?