They seal so make a good storage place for oil cans ect

Great tips thanks, btw i live in tropical country

Kindly tell me does this work well and is durable enough to last at least 3 years with out coil of compressor spoling

@@kirabirarobert1920 It depends on the condition of what you start with, what you use it for, how long it is running per day.

Fan not required. 🙂

Thanks bro for this great comment

👍😉

Hi you say this tank he's using was designed for much higher pressures do you know how much? And do you know how heavy it is? And when full of gas how heavy then?

@Dragomir Ronilac somebody has to be the first to try things to embark on newer knowledge. I'm just looking for a work around if I can find one

@ Don Natalie Lucas, I’ve been watching some compressed air videos, there’s a surprising lack of knowledge not only around good practice but more worryingly the devastating effects of compressed air when it goes wrong. From using propane tanks, to tyre inflation one guy is aiming for 300psi. Just hope people who are unsure what they’re doing just buy an off the shelf compressor.

@@hitop2365 I personally witnessed the aftermath of an air tank explosion over 35 years ago. Everyone was fortunate to have not been there when it happened because the amount of devastation would have easily killed us. It was also good that a vehicle wasn't in the shop because the damage would have cost thousands of dollars to repair. A portable air compressor (I think it was a 30 gallon tank) that was rated to operate at 150psi had a sticking shut off switch that wouldn't shut off until around 175psi. It also was an older unit that had been placed under the corner of a farm shop bench made of rough cut 2x8 wood. It had not been pulled to be drained regularly & would only get drained when there was a significant amount of water coming out of the hose. We would unplug it when not in use, so the nobody worried about changing the cut off valve immediately. It was slated to the "next trip to town" status. One night we had forgotten to unplug it after working in the shop. About midnight there was an explosion loud & violent enough to be felt in the house about 100 yards away. When we got t the shop, there was a corner of the concrete block building blown out about from ground level to the 4-5 foot high mark & around 10 feet down the wall. Pieces of the boards from the bench were strewn about as well as parts of the 3 layers of 2" thick wood from the edge of the sliding door. Inside there were parts of the air tank blown into the ceiling, the door, the opposite side wall 30" away, & into the 14ga toolbox in the opposite side corner. Looking at the parts showed that the tank was pitted in the lower 1/4 level. We knew the cut oof device was defective but had not even thought about the safety pop off, which was found & was stuck shut. The motor was located nearly halfway to the house & the compressor unit was obliterated. We learned several valuable lessons that day. The best were that the tank MUST be drained EVERY day, to periodically check the pop off, & replace the cut off device IMMEDIATELY when it is defective.

Фала брат

Thanks !

Hvala Brate 👍😁

Thank you!

Some fridge compressors have oil coolers

those fan expose also not safety at all, should at least make a cover

Nah mate, you're wrong about the cooling part. The air that gets compressed releases a lot of heat into the compressors. The fan is useful for cooling them down. In a fridge there's usually a plastic cover on top of the compressor. That's where the water that condenses in the fridge runs off to. When the water heats up from sitting on top of the hot compressor is evaporates and cools the compressor. So the fan is actually a very good idea.

These compressors are designed so that the stator is cooled by the refrigerant returning from the evaporator. The fan is to cool the exchanger or condenser, helping the thermodynamic cooling cycle. So it doesn't really help much to cool the compressor motor.

👍👍

Thanks my BRO 👍😊

as you said it looks like a professional but it doesn't come close to that, it's very amateurish, let's buy the parkside better than the lidl

👍😁🆗

Thanks

Thanks

Most welcome 😊

Hvala na komentar

Thanks 👍😁

Thanks !

Thanks

Hi, this fan is mounted here because it needs to cool the two small compressors from the fridge...and to extend the life of compressors ..

Thanks. I guess I hadn't thought they hear up as much... and that the other similar project you did with one compressor didn't have a cooling fan. Thanks.

@@MrDKDIY hey man you don`t need the fan if you were paying attention the fan for the condenser to remove the heat from it not for cooling the compressor and yes most definitely need a relief valve and that tank is pitied i would not run the pressure that high good luck

I like it. To protect the tank you could use navel jelly to clean the rust out. And there was a product I used on a motorcycle fuel tank years ago. Have you looked into air water separators. What happened to the coolant?

The fan is to cut your fingernails.

Use copper not ribber hose, jeeze

😜😉

😉👍

The displacement of the cylinders is 8.9cc, the rpm is 2900rpm so the combined (theoretical) output is 51.6LPM (1.82cfm). In practice, i would expect something around 1.6 cfm.

moisture - seen some cheap tire inflator compressors spit out water. lot of water squeezed out of air. they should have dryer/drain or somesuch

Thanks

Thanks BALKAN Mr DK DIY

Sart

👍👍

Hnnvbcnhh

Kkjbfm

Thmnmhbrhbhgv

😁👍

Da i jas mislam takaka hihih tahnsk for Nice commnet !

👍👍👍

👍👍👏😁

Thanks a lot bro 👍👍

😉

Thanks

Thanks 👍😁😉

Wow TnX

Thanks a lot 👍😉

We need review to se if if it will last.

Simple..... you put 10-40 oil in the air intake problem fixed kinda how you put oil in your air tools before you use them

@@sibosifraiscompagny , naaah. It won't. You need to add compressor oil very often. Otherwise you burn the compressor. Your system is open bro!

It’s easy enough to replace the oil with clean mineral oil and that will suffice however the moisture accumulation is still an issue however that can be solved by replacing the oil depending on the frequency of use. If output moisture is a concern regarding your air tools or for painting applications, you’d simply run the output from the compressor into a small radiator fan and then an auto draining moisture trap and lastly plumb it into the tanks. This will result in roughly 85-90% +\-less moisture in output air entering the air tank.

my dad has used a compressor like that for years with no extra lub or filters.

Thanks for the tips!