Some believe low and mid range power can be enhanced by doing this. I show you how.
Пікірлер: 65
@AllThingsSuperMoto10 жыл бұрын
sounds so sick without baffles
@WolfTheMadMan6 жыл бұрын
I've always loved the mechanical sounds in the exhaust of nighthawks.
@blytheluv13 жыл бұрын
It's just slightly louder with a little crisper sound. It has definitely improved power and responsiveness. I am happy with the change. I don't think it's legal to leave off the end pieces, but I am not sure. Somewhere I think I have a clip of the exhaust sound before the modification..If I find it I'll post.
@Hendrix.9 жыл бұрын
Did you do a before & after gas mileage results?I'd be interested to find out if drilling those holes increased or decreased it.It did sound better.
@hockeynate90812 жыл бұрын
it does sound better without the end pieces. i have a 91 nighthawk 750 and i am going to try this but try a couple different things with the baffle and see whats good or bad. ill put a video up of the different sounds.
@toomuchbeer076 жыл бұрын
Sounded better when you took the inner pipes out and ran it open.
@sweetpotato39507 жыл бұрын
modifying exhausts without increasing jet size causes a lean fuel-air mixture that could lead to burnt valves and piston faces
@ugirl211 жыл бұрын
my stock exhaust was custom cut shorties with baffles cut, my vid shows them it sounds pretty wicked just got a used vance and hines for real cheap so im selling them.
@blytheluv13 жыл бұрын
@lynzack No carb work needed with four 3/8's holes on each funnel.
@carrysmith200812 жыл бұрын
ill belive all those exhaust modifications n after marker pipes give u more power,when i see a before n after dyno performence sheet.
@jamesbregel36928 жыл бұрын
My baffles will not come out even with hammering the pilers as I pull. Nor did pb blaster help, I doubt you will respond but I hope you do.
@papatorr36693 жыл бұрын
Well done
@ricardoaurelius9 жыл бұрын
Great Video.. Thanks..
@blytheluv11 жыл бұрын
I need to try that carb modification.
@weedy3975 жыл бұрын
I have drag pipes that sound like yours. Without the backing added back.
@blytheluv13 жыл бұрын
I drilled four 3/8" holes of each side. It has been working great.
@CraigBMM4 жыл бұрын
make a video !! lets hear it ! :)
@richiesympson72482 жыл бұрын
Did you have to do any re jetting
@jgr14412 жыл бұрын
i have an 84 CB700s it basically has the same exhaust. i removed the baffles but i cannot remove the mufflers buried inside the pipe is there anyway i can do this without cutting them open
@PrinceKlutz9 жыл бұрын
I'd like to hear it accelerate thru the gears, approaching thru first and second, and going away third-fifth. That would be a test of sound. Revving it without a load is not a true test. JMO
@dfw_motorrad13298 жыл бұрын
+Nomad Ryder The exact thing I think on every exhaust video.
@CraigBMM4 жыл бұрын
yes .. i'd like to hear it on the road .. going through gears
@gusgarcia89688 жыл бұрын
beauty beast sound
@HB-yq8gy6 жыл бұрын
I did this after watching video, no differences sounds the same.
@blytheluv5 жыл бұрын
but it's possible your engine might perform better?
@InfernusEternum12 жыл бұрын
I just hacked off the tube with a cutting wheel, same effect, less labor.
@smokeymcbongwater35615 жыл бұрын
Whut u dont do to your factory pipe
@362877810 жыл бұрын
thanx
@tonyrichengod92803 жыл бұрын
Hello all. I'm wondering if anyone knows this : Does the 4-1 exhaust system of a CB400 Super Four fit on a 4-2 CB750 Nighthawk? I'm trying to swap the system on my 750 for a 4-1 to reduce weight and noise. Would it work? Or are there better options for this? Thank you.
@Long-nd8bq Жыл бұрын
Delkevic makes a CB750 4-1 exhaust that will fit. It's for the early 80's bikes but it does fit. You just have to shorten the muffler pipe a little to get the mount to line up.
@chrisbrowne4064 Жыл бұрын
Sounds like shit should left the baffles out.
@OkJustAMinute3 жыл бұрын
What is the name of the inner piece? I just bought a nighthawk and the previous, previous owner removed the inner part, for me it's too noisy and I'd like to see if I can find just those parts so I can reinsert them.
@Long-nd8bq Жыл бұрын
baffle
@juntjoonunya92166 жыл бұрын
would have been useful if you had the before sound
@conraderb5 жыл бұрын
Louder is not the same as more low and mid-range power. Back pressure is important, too.
@youridv5 жыл бұрын
no they don't kzfaq.info/get/bejne/oNCAmLOQs9SWcmg.html here's a very detailed 9 minute video by an engineer explaining why "needing backpressure" is a myth
@bricklayerlzdp98254 жыл бұрын
Run it without baffles and retune. Sounds way better
@shawnwhite08sw11 жыл бұрын
I have a 650. it's not quite the same design exhaust, but is it the same concept to doing so?
@blytheluv5 жыл бұрын
probably
@cosmoswanderer59369 жыл бұрын
can i take my those out completely on my 250cc 2005 ? i need it to be louder i was almost hit by a car the other day.
@noahbillingsley83479 жыл бұрын
If you want to burn the exhaust valve out and have to get the engine rebuilt then go right ahead. You can't take those out you lose back pressure
@noahbillingsley83479 жыл бұрын
If you want it louder just buy custom pipes and get the bike jetted that's the proper way to do it
@AlightBULLDOG9 жыл бұрын
Noah Billingsley actually all you have to do is possibly the jet the carb. You burn valves by running lean and engines lean out because of enhancements but usually take more than straight pipe exhaust to do that. If you deleted the stock air box and put shorty pipes on it then yah probably. But all you have to do again is re-jet.
@brianmurphy23826 жыл бұрын
loud pipes don't save lives,smarter riding does
@JesusGarcia-fg6xy4 жыл бұрын
Ll
@Boards0nfire12 жыл бұрын
I have a 450 nighthawk, how did it run without the baffles? I want to take mine out completely, think it'll run good?
@blytheluv5 жыл бұрын
i think so, but some people say you may need to modify the carburation
@JesusGarcia-fg6xy4 жыл бұрын
1
@lynzack13 жыл бұрын
did any carb work need too be done? ie jetting changes
@blytheluv5 жыл бұрын
i added the small washers to needle jets
@blytheluv5 жыл бұрын
you can probably search on that (adding small washers to increase fuel flow)
@elijahjohnston3172 Жыл бұрын
@@blytheluv how many did you add one or two? Im planning on removing the baffles entirely ive read online people having great success with removing the baffles and shimming the needle jets
@drewboyles67196 жыл бұрын
Sounds like someone lit a duck on fire
@carrysmith20089 жыл бұрын
after your done messing with your factory exhaust system,put ur bike on a dyno machine and ur gonna see,you didnt improve in anything it just got louder,ive had 2 buddies put there bikes on a dyno machine after removing the pipe baffles and both bikes,lost between 1/2 to 3HP on top end and the bikes fuel economy dropped from 45MPG to 38 MPG..
@blytheluv9 жыл бұрын
I didn't/don't recommend totally removing the pipe baffles; the modification I did involves drilling a series of holes into the baffles and re-installing them. I wanted to refer you to the web page that I used as a guide, "Tim Hodge Exhaust Mod" on www.nighthawk750.com, but it appears that web page is not working at the moment... But I was able to see a cached version of the page: webcache.googleusercontent.com/search?q=cache:RtmlTDGTpecJ:www.nighthawk750.com/mods/exhaust.html+&cd=1&hl=en&ct=clnk&gl=us&
@bruceclark56278 жыл бұрын
then you need to tell your friends to tale the time to rejet their carbs because after the same mod and rejeting my 1982 450 night hawk seen on a DYNO at C.W.MOTORSPORTS in effingham ill.a 7 h.p. increase at the WHEEL .that also included opening the air box with a stock replacement air filter.
@bruceclark56278 жыл бұрын
also the baffle wasn't removed it was opened up.next time watch the whole video before getting snarky.nothing worse than being arogant and wrong.
@MrPavePaws5 жыл бұрын
4 into 1 replacement. Starts pretty quietly. Up to the power band it sounds like it wants to be seen. At 4500-8000 it has this wheeee that let's ppl know I'm passing them. If I coast in a more relaxed gear (30mph in 3rd not second) it sounds like a classic 50s muscle car BLUB BLUB BLUB.
@elijahjohnston3172 Жыл бұрын
Remove the baffles entirely and shim the needles in thr carbs with 1 or 2 #4sae washers. Will run like a bat out of hell. Thank me later
@timkis64 Жыл бұрын
you got to be careful with honda's.they use backpressure combined with lean carb. jetting to get by the EPA.they are very lean to begin with.when you reduce backpressure it leans them out farther.thats why many honda's run worse than stock when you reduce stock backpressure WITHOUT increasing pilot & main jet sizes.why in the hell would anyone want a louder but slower bike without upping carb jets to compensate.its like only wiping half of your ass.
@ulisesmenmer83602 жыл бұрын
So sad
@d3tach3d5 жыл бұрын
Sounds like shit man. just run it without the baffles.