Wow...you just saved from spending $$$ on timing chain. Thank you 👍
@dogman84367 ай бұрын
Notice the design difference in the old and new Honda VVT solenoid. The original with the rubber rings caused cross leaks after a few years in service as the rubber shrunk and got hard. The new design was a big improvement because the larger aluminum valve lands sealed much better for longer. I just fixed one of these Hondas by using the new design. The original symptom was Code P1009 and very rough idle because the intake cam was staying advanced at idle. Also once had P0341 because of the discrepancy between actual and expected camshaft position.
@Direct_Home_Inspections Жыл бұрын
Changed my VTC actuator. The new one failed in 6 months. Wised up and bought a Honda OEM one this time. Car runs like crap. Thought maybe I timed it wrong and removed the timing cover and put everything back together perfectly. Triple checked it. Still runs like crap. Takes forever to start and is down on power. I wonder if it's that sensor. I put a new one in and if I remember right I dropped it at one point. Timing chain and everything else is new. Unless the actuator is bad from the factory the sensor is the only other variable
@abdelabdel96322 жыл бұрын
I am facing the same malfunction with the same code. I changed the erbracam sensor, then changed the chain, then changed the entire erbracam, then changed the erbracam wheel and checked the electricity completely. However, the same problem remained. My brother advised me
@bb3283 Жыл бұрын
Single A (bank 1) closest to the front of the vehicle?
@neondiamondsaquaberry172 жыл бұрын
I am having the same issue with my 08 accord 2.4. I replaced the crankshaft sensor about 3 months ago with no issues until now. I have p0341 bank A, I replaced that, cleared codes and all 3 lights came right back on. Is what you did able to clear the problem? Engine starts, idles and drives perfectly fine even with the lights on. Thanks
@mydiygarage2 жыл бұрын
Unfortunately, it is the timing chain issue. You may have to adjust the timing chain since it jumped. That's what u end up doing.
@hassanelakhras2760 Жыл бұрын
hi Neon, got the same problem, any update?
@bsea8499 Жыл бұрын
Had the same error code. Changed both camshaft sensors and the timing chain. New error code popped up as P0365.
@plexandremdog Жыл бұрын
I changed the bank 1 sensor and I also changed the vvt sensor but the code is still on even after I reset. What could be the problem
@jameshogge4448 Жыл бұрын
possible vvt control solenoid on the back passenger side of the head or could have jumped a tooth, those timing chains are known to stretch
@Apdc5k24 Жыл бұрын
Did this fix the 0341 issue?
@lastof4brothers6 ай бұрын
What you brought out is significantly different from what you put back in, yet you say "everything is the same". Care to explain?
@zeemughal8610 ай бұрын
Does anyone’s cruise control not set when these codes are on?
@encarnacioncamacho720110 ай бұрын
Yah mine stopped working to it’s throwing the vsa light and the same cam shaft code i done replaced both cam sensor and the vtc solinoid so right now I’m at a stand still car running like shit
@nickwickersham879 ай бұрын
@@encarnacioncamacho7201any updates??
@wehaveawoken5975 Жыл бұрын
I have the same problem. Car runs pretty bad, vtec starts 1000rpm later and the fuel consumption has rocketed. Changed timing chain 2021. Changed cam and crankshaft sensors. I have a vvt solenoid here, I hope this will fix it otherwise I'm going nuts.
@glizzyrewind6570 Жыл бұрын
Did it fix your problem Reply please
@charlesferrari9127 Жыл бұрын
@@glizzyrewind6570 I haven't had time to fix it yet. Maybe I'll try it this weekend or I'll wait for mid of may when I will take the car to the mechanic. I'll key you updated.
@nickwickersham879 ай бұрын
@charlesferrari9127 any updates on this?
@frazer95 ай бұрын
You're driving yourself crazy by fixing things on your car that dont need fixing. Use your brain. Diagnose the problem from the start