Having just rebuilt my 1981 CBX carbs and reinstalled them, I found your video very valuable. Thanks! Of particular note is the attachment of the choke cable which is incorrectly shown (reversed end-for-end) in the 4th edition "how to" guide of a famous CBX specialist. If installed like he shows it WILL bind up. Yours is correct. Also, when installing the clamps on the intake tubes (rubber donuts) I find it best to place them on the tubes before installing the carbs. All of them can be accessed for tightening from the upper side of the donuts except for the #3 and #4 clamps on the head side which must be accessed from the lower side because of the engine mounting bosses in the head. Thanks again, great videos!

Nice work guy 👍🏼

I always get excited when you give another piece of this wonder puzzle!! Thank you and great work!

Amazing video. Wish I’d watched this before I restored mine. The pre install throttle cables and the wood trick would of saved me two days lol. I eventually figured it out just like you did. Except I used wood and a little screw jack lol. I couldn’t believe how tight those suckers fit.

This video very very helpful thanks

That was awesome! Thanks Pete, keep them coming

Thank you, I got a 79 that has been sitting for a few year that I been scared to play with, your video's gives me hope.

Been waiting for this and it’s been well worth it, looking forward to the next instalment, thanks 👍👍👍👍

Amazing! Great job 👍

happy to see your incredible job again after months waiting for!!,congrats for so marvelous work!! hope you dont forget us!

Super video! It helped me a lot. Many thanks!

For everybody asking the hp numbers- this bike put down 197 hp at 17 psi. Forged pistons rods head work etc.

Nice video, wish it had been available when I did my carbs many years ago. A couple of things to note: I would do the accelerator pump while you're in there as they get a little stiff over time. Also would agree that you don't want to go cheap on the rebuild kit - the one I bought had some pretty sketchy plating and the profiles on the needles were horribly off. Since there should be no wear on the needles, I just re-used the originals. Great video and thanks!

Great Video! Keep the cool content coming.

I did my carbs years ago. They are a bit complex as a unit and a slight pain but so unique as is the whole engine...nothing else like it.

Nice video, the whole series is excellent, I was waiting for the "put together the carb” part, looks like was removed… very illustrative… Thanks, I used to rebuild my carbs 1982 cbx

great video . wondering do you check the float levels with a caliper ?

That many carbs takes so much time, and would not be for the faint of heart, when it comes to Patience !

Do the rebuild kits also come with the o rings that go on the tubes that feed the carbs fuel?

Like your videos very informative could you do one on balancing the carbys with the vacuum gauge s thanks

23:30: I'm also using a hairdryer to heat up the rubber intakes, it makes them easier to cooperate with 🙂. Im struggling a bit with the choke, since it does not rotate that smoothly. Looks like my choke axles on the carbs have a bit of a slack there, can these be tightened up?

Great work and I like the video. Do you plate or polish the carb tops?

The Honda manual suggests not re-using the choke valves, shaft and screws on the carburettors. How do you get round this as they are not available for replacement?

Hi I have two sets of carbys both have a 13 mm Long hose connecting carbys 1&2,5&6 is the hose only supposed to be on those two or all the carbys re peter hope you can help me thanks for your videos

Nice job sir, i need help I have a 1982 cbx and i find under the carburator a spring, 2 washers and a plastic buching and the parts from the aceleration pump linkage arm, do you can tell me the instalation order and i need get a small cut pin. Thank you Wagner Damotta

Hi found what I was looking for joint set fuel re peter

Damn they have filters in the carbs too? Wow. But I can see that causing a problem

What about checking float heights

where can i find part 2 where you assemble the carburetors

is there a part 2? I'm having a hard time assembling the butterfly choke flaps back on. the spring and flaps I just can't get to work together.

Hi - let me know when the CBX 1000 will be for sale ;)

Hi Michael. Great video. So much effort to be clear. I can’t seem to find Pt2 of the carby rebuild on your KZfaq channel. Have you completed it yet? If so what is the title of it so I can search it? Cheers

At 15:45, it appears that the "O" Ring was left out of the 3rd Carburetor Bowl. I caught the error during assembly and the O Ring was installed before the carbs were installed.

Where do you purchase your carb kits? Happy Friday!

Not that helpful missed out a lot of the parts that need new o rings & removing