Honda Civic Si action clutch stage 2 Install 9th gen 2012-2015

Рет қаралды 8,821

9 ай бұрын

Tools used
Jack stands
Hydraulic floor Jack
Bottle jack
Ratchet straps
Pilot bushing puller
Rubber mallet
Prybars
3/8 1/2/ ratchets
Torque wrench
Assortment of pliers and chisel
Hammer
Sockets sizes 12,14,17,19 In shallow 3/8
Sockets sizes 10,12,14,17,19,21 in deep 3/8
36mm axle nut socket
10 and 17mm 12 point socket
Assortment of extension
Combination wrenches sizes 12,14,17
5mm Allen socket 3/8
Drain pan
Funnels
Towels
Brake clean
Blue locktight
Honda Manuel transmission fluid
Clutch kit www.kseriesparts.com/ACR-0666...
Flywheel www.kseriesparts.com/ACR-AC10...

Пікірлер: 39

@adyo92 5 ай бұрын

That’s a badass mullet homie!!

@pablosgarage707 5 ай бұрын

Thank you appreciate it!

@mjyu6510 5 күн бұрын

Thanks for the helpful video with tons of useful info! 😁

@pablosgarage707 5 күн бұрын

Glad it was helpful! I’ll have More DIY videos for the civic as time goes on and I do more part replacements. Eventually, when I move out of California, I’d like to do a supercharger that way I don’t have to deal with smog regulations etc… thank you for watching appreciate the support!

@Fb6.Nan0 7 ай бұрын

this is an awesome video bro!!!

@pablosgarage707 7 ай бұрын

Thank you appreciate it! More 9th gen videos to come as I work/ modify it! Thanks for watching!

@connorcornejo1002 29 күн бұрын

Watched this video about 4 times now LOL doing the clutch tonight appreciate the detail

@pablosgarage707 29 күн бұрын

Awesome let me know if you need any help! My Instagram Instagram is tagged on my KZfaq channel. Feel free to send me a direct message. I try to be as detailed as possible, but when I got the wrong flywheel, and my daily was down filming, unfortunately became the second priority 😭

@connorcornejo1002 29 күн бұрын

@pablosgarage707 completely understandable haha. If I have any questions I'll reach out. Gonna follow this fir visuals and the honda manual for anything else haha

@hellaslowcivic 7 ай бұрын

The actuator you pointed out is actually a shifter actuator, they have springs on em that could be upgraded for future references, which is sold by hybrid racing.

@pablosgarage707 7 ай бұрын

I see. Awesome. Thank you for the information 👍Have you done the mod? I’m considering doing new cables and springs.

@hellaslowcivic Ай бұрын

I've have the springs needa throw them in I've done the detent springs and the shifts are very noticeable. I'd recommend those as well. I got cables too 😭 I'm just trynna get a short shifter before I throw the cables in

@Deetzat 4 ай бұрын

Hey man not to sure if you still post or do KZfaq anymore. I’m getting the fx350 installed by me and brother. Where are the exact issues you ran into? I skimmed through the video but my brother doesn’t quite have the patience. He thinks it’s an easy job, but he also did his Subaru where he had to pull the whole motor, and his 5.0. He said with all my tiny parts it’ll be a piece of cake. What do you recommend me picking up for extra help, and where will we struggle with the most you think? He’s a mechanic so he has to deal with axels and rack and pinions everyday, by other than that what do you recommend for making this job easier?

@pablosgarage707 4 ай бұрын

This Honda is one of the easiest clutch jobs. If he’s done the clutch in his Subaru, this civic will be no problem. There really was not anything that stood out from being insanely difficult.

@paraxicgaming5743 7 күн бұрын

How much time you think is needed if you have all the tools already? Multi-day job? My 13 is making a rattling noise down there ofc can't hear it too good over the lifter tick i have but i think maybe the fork is loose, my clutch bites practically off half an inch off the floor(not sure if that's how it's adjusted or if the cable is stretched i mean i know it's gonna bite lower than my bros mustang but I'd like the bite to be a little higher than barely off the floor)

@pablosgarage707 3 күн бұрын

It can be done in an entire day. For me I got screwed due to having the wrong flywheel. I ended up ordering the correct one and got it done. That slowed me down drastically.

@danielsantiaguel79 5 ай бұрын

Will it fit for 2013 honda accord engine (k24wz1)Been researching for so long and came up in a website they saying that kseries are interchangeable clutch but i need help guys

@pablosgarage707 5 ай бұрын

It may however I think your accord is a five speed. I would call or email action clutch. I just checked on their website and I don’t see your accord available as an option :(.

@warworm100 4 ай бұрын

Is draining the fluid absolutely necessary? This is the only vid I’ve seen that’s mentioned that. Ab to do this job today and wanna make sure I’m prepared.

@pablosgarage707 4 ай бұрын

Not necessary. I just did it because it was due to be changed. Also in the past on other vehicles I have left the transmissions full with fluid and when I layed them down they leaked out all over the ground. On the civic when removing the transmission it will most likely leak out of the input for the cv axles. I would drain to avoid making a mess

@Honditosi 5 ай бұрын

Great company got a stage 4 and runs perfectly

@pablosgarage707 5 ай бұрын

Awesome good to hear! I love my new clutch

@aochio9735 4 ай бұрын

do you know whats the part number of the original clutch. is it from excedy or other company>?

@pablosgarage707 3 ай бұрын

It’s from exceedy throtl.com/products/exedy-oe-12-15-honda-civic-si-l4-clutch-kit-hck1015

@zzwk24 Ай бұрын

So the trans should come out that smoothly? Sheesh, mine needs to be pried

@pablosgarage707 Ай бұрын

lol. I’ve been there before with some cars. Are you In a salt area ?

@zzwk24 Ай бұрын

@@pablosgarage707 not really, but I did end up getting it out, it wasn't stuck actually. I didn't want to remove the intermediate shaft, so I did a gently back and forth pry and used the jack to move up and down to slowly separate the transmission from the shaft and then it came right out. 🤷‍♂️🤦‍♂️🤣

@Mansimran24 7 ай бұрын

So basically you need a k24z7 clutch kit with a k20 flywheel? Also was the k20 flywheel oem weight? Did you had to tune the ECU ?

@pablosgarage707 7 ай бұрын

I accidentally ordered that one. It was listed as oe hd however it was incorrect. I used this flywheel. www.kseriesparts.com/ACR-AC102-FFW.html identical to the Factory flywheel. No need to reflash weight is identical to stock.

@Mansimran24 7 ай бұрын

@@pablosgarage707 can you provide a link to the clutch kit as well? Thank you. Also, how does the car feel with the new clutch?

@ikzuq 7 ай бұрын

@@Mansimran24the only tune u need for a new clutch to get rid of is the knock sensor or one of the sensors

@ikzuq 7 ай бұрын

@@Mansimran24its a stage 2 action clutch they have a site, i just got me a stage 1 with a 10lbs flywheel, finna give it a go rn

@ikzuq 2 ай бұрын

You can actually do the whole job without dropping the subframe all the way, just drop it on the driver side and move the suspension as much as u can to the side and adjust as needed, ofc have support on the bottom of the tranny just in case but u should be able to rotate the transmission in the bay just fine

@pablosgarage707 2 ай бұрын

Agreed. For me I find it easier to just drop it and have all the room available to work with.

@ikzuq 23 күн бұрын

@@pablosgarage707I had to do it again cuz I got smacked by a drunk driver and my clutch went out, I dropped the subframe this time cuz it’s abt the same time, ima finish it off today hopefully 😂🙏