HONEYWELL T9 SMART THERMOSTAT INSTALL

Рет қаралды 57,031

4 жыл бұрын

Пікірлер: 29

@billweber6657 2 жыл бұрын

You dont have to use the jumper wire between R and Rc. If you only have one wire and a jumper leave the little slider in the up\1 wire position. Then just insert the red to R. The slider creates the jumper. Great video. Thanks.

@davidturk417 Жыл бұрын

Actually, I may redo mine WITH the jumper as he did in the video! I've been having issues a couple months after installing my T10 (virtually identical to the T9), with it not lighting the ignitor and opening the gas valve. Manually jumping R to W on the IFC board in the furnace cabinet seems to work. Now, I'm suspecting that the built in sliding jumper, which seems a bit loose, may not be making good contact between R and RC on the T10 terminal base.... I may try this trick, and jumper R to RC, and see if that gives a more reliable current.

@briangow6282 2 жыл бұрын

*Works great: **Fastly.Cool** and Warming environment perfectly controlled. I use 3 in different grow tents. It’s nice to see from your phone how your tent temps are. Does High and Low and records data.*

@musicluvr0795 5 ай бұрын

you made this look easy! thank you for the perfect explanation. i’ve been considering installing a smart tstat in my rental townhouse because it is currently located in an uptairs hallway/open stairwell 🤦🏻‍♀️ we spend most of our time downstairs and it is SO hard to temp control. anyways i’ve done some research and this one looks perfect for what i need but i was intimidated by having to install it. you’ve given me the confidence to pull the trigger! thanks again!!!

@jbarry5886 4 жыл бұрын

I found this useful, although I have an old Honeywell I'm considering to replace. Thanks.

@csaiz8847 11 ай бұрын

Thank you poating your video. I am switching to this same thermostat soon.

@josel.dominguez6747 3 жыл бұрын

Thanks for sharing your nice video and regards.

@tinac3105 4 жыл бұрын

Great video but during the video I am looking at the cut on his hand thinking god that had to hurt.

@wickedwood04 3 жыл бұрын

Great Video. Thank you.

@TheVeroneeLife 3 жыл бұрын

Glad you liked it!

@xerinaka Жыл бұрын

Thank you!

@RonnieRukus 2 жыл бұрын

Thanks for the info. We just bought a house that was built in 1920 with 2 additions that has 2 HVAC systems. I want to get two of these with multiple sensors for each system. One of them is in the basement, so when the temp in the basement is perfect, the upstairs is roasting 😂

@emanuelcollado1343 2 жыл бұрын

Great video though I only have a yellow and red wire only 2 wires

@kwrzesien17 10 ай бұрын

You mention having a furnace and then call it a heat pump at one point and I can’t tell from the wires what you might actually have (the W is used on heat pumps for defrost, wires directly from stat to outside unit). Wish there were more good videos on the heat pump connections because they replaced our AC unit with a heatpump but we only want it to run as an AC, already have a 90% eff. gas furnace on that unit. Problem is the T9 can’t be wired for “dual fuel” but maybe the T10 can, will be calling Honeywell today. Depending on the heat pump manufacturer the orange wire either needs to be joined to the Y at the unit (powered on call) or left capped (no power) so the heat pump knows to run in cooling mode only. O (orange) controls the reversing valve, and you don’t want it jumped on all the time or it might burn out. Looks like W (white/defrost mode) can be left disconnected for AC-only use. I jumped Y1 and Y2 on my Lenox 2-stage but might have to redo that or some mode jumper on the board because it never kicks down to the second stage with more cooling.

@kwrzesien17 10 ай бұрын

Found a better description of heat pump wiring (W, O/B) here: kzfaq.info/get/bejne/qsxigtt0qd3Qdo0.htmlsi=CMtVRz2XNGQGlnwP

@PlayshotKalo 5 ай бұрын

Any way to install this with only 2 wires?

@heaventoshop 4 жыл бұрын

Please tell my husband to cut the power off at the breaker!!!!

@555reuben 2 жыл бұрын

Always a good idea. Low voltage like this isn’t dangerous, but if you accidentally short them, you can blow a fuse in the furnace

@tinamr4757 3 жыл бұрын

HI I need your help with wiring . PLease I was trying to install this thermostat Honeywell T9 but I found many wires 1 Yellow, 2 Red, 1 Green, 2 White , 1 Blue . I don't know what to do !!!

@emanuelcollado1343 2 жыл бұрын

Good luck hire an electrician I only have 2 wires red and yellow

@kwrzesien17 10 ай бұрын

You probably have a heat pump

@jeffreywashington5461 2 жыл бұрын

I was hooch that I could install this thermostat minus the c-wire. Is there a way?

@kwrzesien17 10 ай бұрын

Yes the T9 comes with a C-Wire adapter that plugs in at the furnace control board.

@jaywilliams1994 Жыл бұрын

Now, what happens if my blower won’t shut off?

@kwrzesien17 10 ай бұрын

G (Green) drives the blower fan. Make sure the thermostat is set to Auto fan mode and Heating or Cooling mode on, change temp so it doesn’t run. If fan is still going check the green wire is not jumped on either side. G should go to G between stat and control board only (does not go outside). If stat is set to Fan Always On or Circulate mode that will turn it on as well when properly wired.

@jaywilliams1994 10 ай бұрын

@@kwrzesien17 Ahh.. thanks. My apartment already burned down but i’ll remember this when I move into my next spot.

@kwrzesien17 10 ай бұрын

@@jaywilliams1994 Yikes, stay safe!