Hope Pro 4 Rear Hub Bearing Replacement Including Freehub

Hope Pro 4 Rear Hub Bearing Replacement Including Freehub - In Depth

Рет қаралды 17,271

Күн бұрын

0:00 What the video is about - This is a LONG video
0:56 Removing end caps
02:20 Removing the freehub from the hub
03:35 1mm spacer
04:20 Removing rubber seal (Disc side)
05:03 Removing the axle from the hub & bearing
07:00 Removing the bearing from the axle
08:45 Removing the remaining bearing
09:40 Quick look at the axle
09:57 How the hub looks without bearings
10:17 Removing labyrinth seal (Green ring)
10:43 Freehub pawl & spring removal
11:40 Freehub tube, need to be able to move it
12:50 Removing bearings from freehub
14:55 Bearing details sizes etc
17:36 Why you should press the freehub bearings in too much
17:55 Installing freehub bearing with cheap tools
24:15 Close up of bearing after install
25:02 Don't forget the tube/spacer
25:45 Important part
26:25 2nd freehub bearing install with a press
29:14 Make sure the tube can move
29:26 Install labyrinth seal (Green ring)
30:00 Clean pawls and springs
30:21 Surface rust
30:51 Installing freehub pawls and springs
32:32 You will need a deeper press tool or long socket
33:40 Installing hub bearing, freehub side
35:51 Close up of the 1st hub bearing after install
36:18 Installing hub bearing, disc side
40:23 Close up of the 2nd hub bearing after install
40:30 Install the rubber seal
41:02 1MM SPACER!!
41:20 Installing your freehub
41:55 Installing labyrinth seal (Green ring)
42:55 All finished
www.hopetech.com/_repository/...

Пікірлер: 20

@austinwilliams7085 9 ай бұрын

Excellent,you have taken all the guess work out.Very thorough 👍

@paulcoateshome Жыл бұрын

Fantastic video tutorial, just what I've been looking for! It's a job I aim to take on myself and have been looking on KZfaq for something like this for a while now.

@Chambers36TheEnter Жыл бұрын

Thanks for the kind comments, glad it is of help. I'd wish you good luck when you do yours but I don't think many people will have too many issues to be fair, it's quite straight forward.

@fuddyduddy306 9 ай бұрын

Thanks for sharing. I found this much more informative and easier to follow than the Hope video. The first time I did this I was unaware of the deep press tool sold by hope. Definitely made the job easier this time! I still struggle getting the green seal back on though. The Hope tool for this isn't even worth buying in my opinion

@Chambers36TheEnter 9 ай бұрын

I'm not a fan of installing the labyrinth seal either, just feels like you're going to break it even with the correct tool.

@neilgoddard9613 11 ай бұрын

Briliant video with lots of detail thanks

@Chambers36TheEnter 11 ай бұрын

Thank you, glad it was of some help!

@adamtaylor7871 11 ай бұрын

Brilliant in depth well explained stuff thabks

@chrisandrews5881 Жыл бұрын

Excellently detailed video, looks like the process for an Nukeproof horizon v2 hub would be very similar? Do u not need to use a freehub oil/grease for the pawls?

@Chambers36TheEnter Жыл бұрын

Thanks, tried to make it as short as possible. I would say a lot of the hubs now have a similar process unless they are shimano which use cup and cone bearings still. I would run some sort of lube where the pawl comes into contact with the freehub body only because it's metal on metal, how long that lube actually stays in the gap I don't know. Else where I don't use grease or oil as it's a bit of a "magnetic" for grit and dirt but if you wanted to you can just don't use a lot of it. Hope stick a few blobs of grease inside the hub where the freehub sits.

@19Nick80webb Жыл бұрын

Awesome video, I have a few hope pro 4 rear hubs that need new hub bearings, I’m wondering where to get all those tools in your video? as I have three rear wheels with grainy bearings after 80,000 miles each …

@rydawgdawg Жыл бұрын

Where did you find the new bearings? I can't seem to find them anywhere

@Chambers36TheEnter Жыл бұрын

I normally go to a company called Wych Bearings. You can enter either the bearing code 6001rs for example or the dimensions 12x28x8 in their search bar and it will bring up different qualities of that size. Simply Bearings is another company that I use. On ebay I use kineticbearings or airevelobearings. Once you know the size you can find who has the best price.

@shadeed68 5 ай бұрын

can you replace a micro-spline body with a HG body on the Hopepro4? (12 speed cassette)

@Chambers36TheEnter 5 ай бұрын

Hi, yes this is possible. They just swap over. Reuse the same green seal.

@stevebarton9469 Жыл бұрын

Does the XD use the 1mm spacer?

@Chambers36TheEnter Жыл бұрын

I would use it. It shows in the parts list on the hope site for the XD dirver. HUB1009-18 www.hopetech.com/_repository/1/documents/Pro-4-Freehub-Assemblies1(1).pdf