Thank you for such a in depth video, this is what youtube is about, sharing knowledge and helping others!
@tractorsmarinemechanic Жыл бұрын
Thank you for watching.please help my KZfaq channel by subscribing.ty
@fulken832 жыл бұрын
Im getting my generator running thanks to your video! you are easier to follow than most, without even saying a word. great work!!
@tractorsmarinemechanic2 жыл бұрын
Thank you for watching.please subscribe,share and like.thank you
@tommoody31275 ай бұрын
Excellent video. Thanks for sharing your expertise. You covered all the sniggily details.
@scottstuart91583 жыл бұрын
Thank you for showing this video without it I would not have been able to repair mine. Thank you sir.
@tractorsmarinemechanic3 жыл бұрын
Thanks also for watching.pls subscribe,hits likes and share.
@tractorsmarinemechanic3 жыл бұрын
Thanks also for your watching.ples subscribe, like and share
@chatking6969cody2 жыл бұрын
Thank you for the upload. I had trouble removing the pump because the governor slide pin was stuck I had to use a screwdriver to slide it over. I am sending the pump to a diesel pump rebuild shop.
@tractorsmarinemechanic2 жыл бұрын
Thank you for watching.
@Ironman49693 жыл бұрын
Thanks great detailed video, helped me to reassemble my KIKI nippon injection pump.
@tractorsmarinemechanic3 жыл бұрын
Thanks. you can watch more just cliclk from playlists for some other injection pump.
@WeekendGarageKorea2 жыл бұрын
I can understand pump mechanism with your video. thanks 👍
@nataliusluhat1402 Жыл бұрын
Terimakasih, Berkat video ini, unit saya, bisa saya perbaiki sendiri. Video yg sangat bermanfaat👍👍👍
@tractorsmarinemechanic Жыл бұрын
Thank you for watching
@wfhg942 жыл бұрын
very good your video have video that kubota pump 1J700-51011
@nmdfredesc.99187 ай бұрын
Not your fault, but there is a MAJOR problem with the absence of an explanation about the fuel injection DIRECTION that the PLUNGERS must be aligned with. Hard to understand for many, but the plungers MUST be installed properly. Meaning that the "vertical-helicoidal" groove on them must be aligned to spit the dose of fuel as needed. The square end (rectangular actually) come with two different inscriptions at each end. If you don't know how, your motor will never start. More yet. Tons of videos about these pumps. NO ONE ADRESSESS this fact!
@ahmadasriri7 ай бұрын
فنان ومبدع❤🌹💕
@Epic_Catches Жыл бұрын
I’m working on this same engine, guy ran it out of fuel can’t get and fuel to come out of the injection pump, plenty of fuel going in. Loosen delivery valves and it will let out low fuel pressure
@Slash-lw6ds3 ай бұрын
Is the same as a leopard same 85 exp
@sumanmondalsuman76353 жыл бұрын
Thanks you very much 👍👍👍 ❤️❤️ ❤️ Good working Engine HP___? Engine fitting video fako
@jay-arates39312 жыл бұрын
Klarong klaro sir,,,salamat
@rajanaeem62922 жыл бұрын
nice sir
@tractorsmarinemechanic2 жыл бұрын
Thank you for watching.
@mrglabs4778 Жыл бұрын
Beware when removing this pump the rack needs to be in a forward position else it will get bent. Also, there is a small rack dampener pin at the rear of the pump that can become damaged. It is not available from Kubota alone. Bending it will be very costly. I was able to straighten mine. Hopefully it will work.
@parvellusk6345 Жыл бұрын
any idea where to get internal parts for this pump?
@tractorsmarinemechanic Жыл бұрын
None
@billkrummel859010 ай бұрын
I have a v1702 after cleaning and reassembling the injection pump fuel only comes out of cylinder 2 injection line, and if i loosen the fitting ontop of the pump the others will pump fuel . Any idea what would cause this?
@tractorsmarinemechanic10 ай бұрын
Check your delivery valve
@billkrummel859010 ай бұрын
Ok, at 16:03 you put a washer on. My pump is missing those, is that a normal copper washer? And what size is it? Will the pump function without?
@tractorsmarinemechanic10 ай бұрын
Without washer diesel will be mixed to the oil pan
@mrglabs4778 Жыл бұрын
How does the pump come off the engine? I have all the lines and intake manifold removed. Is the linkage going to prevent it from lifting off? My pump has no fuel out of one valve after I had water in the fuel. Only 218 hours on this engine.
@tractorsmarinemechanic Жыл бұрын
Remove the delivery valve holder and check the delivery valve maybe stuck
@mrglabs4778 Жыл бұрын
The rack was stuck towards the rear. It bent and would not move. I managed to get the pump out and straighten the rack in a press. Now I hope I got the plungers back in the correct way. Slot goes towards the rack side?
@mrglabs4778 Жыл бұрын
The plunger that you install at 17:50. Looks like the slot goes on the rack side. Is this correct? Thanks
@tractorsmarinemechanic Жыл бұрын
👍
@joeabm83072 жыл бұрын
Thks bro...keep my money 🙏👍
@tractorsmarinemechanic2 жыл бұрын
Thank you for watching.pls.subscribe and share...
@codybabb1472 жыл бұрын
I have a question I have a kx71-3 with v1505 motor. Idles fine but smokes black pretty good and soon as you put load on the motor it dies down and smokes like a train. Wondering if you could give me some ideas what to look for or check out. Thanks
@tractorsmarinemechanic2 жыл бұрын
Kindly check the air cleaner
@codybabb1472 жыл бұрын
@@tractorsmarinemechanic runs no different with air cleaner in or not
@tractorsmarinemechanic2 жыл бұрын
Did you overhauled your engine or not?may be your engine slightly blowby or the plunger need to replace
@codybabb1472 жыл бұрын
I replaced the head recently but it doesn't really have any blowby. Or at least excessive blowby. . I was next going to rebuild injectors and ip. But I don't know a way to test them
@codybabb1472 жыл бұрын
@@tractorsmarinemechanic it ended up being I guess compression like you said. The whole rocker assembly came loose and wasn't closing the intake valve the rocker was actually off the push rod completely. Tightened it all up set the lash and it fired right up ran good
@Tejdor01 Жыл бұрын
thanks a lot!
@tractorsmarinemechanic Жыл бұрын
Thank you too for watching.
@Slash-lw6ds3 ай бұрын
Has anyone worked a leopard same 85 exp.need to know how to remove from engine..
@maxpuppy9611 ай бұрын
After seeing one tore apart there is really nothing that can wear out in them.
@dotsie19783 жыл бұрын
What is the solvent you are washing the parts in?
@tractorsmarinemechanic3 жыл бұрын
Its a diesel
@johnvenkat86 Жыл бұрын
Sir, what is the stamping number on elements and DV
@tractorsmarinemechanic Жыл бұрын
stamping number is not available
@adamguitar90 Жыл бұрын
Is if only I could find replacement parts for mine
@tractorsmarinemechanic Жыл бұрын
Thank you for watching
@rachutiyadagiri46033 жыл бұрын
Hyderabad workshop where
@tractorsmarinemechanic3 жыл бұрын
Philippines
@rajudumala20043 жыл бұрын
Where is the location
@tractorsmarinemechanic3 жыл бұрын
Philippines
@tractorsmarinemechanic3 жыл бұрын
Thank you for watching.pls Subscribe
@anasrulirawan32192 жыл бұрын
Mas kode plunger nya berapa
@tractorsmarinemechanic2 жыл бұрын
Code or numbers of plunger is not indicate.
@wfhg942 жыл бұрын
very good your video have video that kubota pump 1J700-51011
@tractorsmarinemechanic2 жыл бұрын
Thank you for watching.please share and subscribe.
@wfhg942 жыл бұрын
friend any email to, to ask a technical question. Thanks a lot