How to carb a keg quickly.

Рет қаралды 26,044

Brew Simple

2 жыл бұрын

Step by step video on how for force carbonate a corny keg of beer in under 5 minutes!

Пікірлер: 25

@hatherlow 2 жыл бұрын

I do the same, important to note I have a non return valve between the regulator and the gas out so that can't get any beer back through the regulator

@robertmcinnes5447 2 жыл бұрын

I wish I had that knowledge months ago!. Keep up the great work Mr J

@erniq3 2 жыл бұрын

Great job mate, very helpful

@danssv8 2 ай бұрын

Great video mate

@1kreature 9 ай бұрын

Put a towel on the table so you can hear what you are doing inside the keg.

@ExpiredFreedom 2 жыл бұрын

we do a similar method at school but we usually let it sit for a few hours after not even because of the foam but I heard the aromas are somewhat diminished following the carb and settle back out after a while

@dudemanphat 2 жыл бұрын

Is this a technique to use only if you are pressure fermenting and the beer is already partially carbonated? I usually use higher pressure and have foamy pours for days before it settles. WIll try this way next. Another great video.

@ChadandTiffC 8 күн бұрын

What if you can’t pressure transfer?

@Soupy_loopy 2 жыл бұрын

This is a really great way to wear out your coffee table!

@chililovers4332 2 ай бұрын

Is it too over if the liquid going inside gas line?

@javierdelpino5436 2 жыл бұрын

Hi, thanks for your good video. I´ve question, did you put the CO2 in the in of gas or in the in of liquid?

@brewsimple2555 Жыл бұрын

On the gas mate

@dripkratomkavavapor8782 8 ай бұрын

The video was great...thank you! How do I flavor the force carbonated keg? I've tried Torani & Monin syrups...but it just doesn't taste right. Is there a "special carbonation flavoring"?? Thanks in advance!

@Progfan2010 Жыл бұрын

What if the keg is a 2.6 gallon keg? Would you shake it for 2 minutes?

@alfonso45901 8 ай бұрын

It will just take less time for the hissing to stop but i would think it’s half the time of 5 gallons

@marcoafzelius9541 3 ай бұрын

Hi, I’m trying to carbonate home made sangria. It’s essentially 60% wine/ 25% triple sec / 15% whiskey. I have zero idea what im doing. But i have the 10L korni keg and the c02 on hand. Can I use the same method shown here? How much pressure should i set the gauges to?

@Chrishopter 2 ай бұрын

You can carbonate anything you want. Yes this method works fine for what you’re asking. Average line pressure is around 1.5

@allenlinderman191 3 ай бұрын

Stupid question, but...do you attach the CO2 to the IN or OUT ?

@LorenzzoMuzicOfficial 2 ай бұрын

@deemlor 2 жыл бұрын

Does this work at room temp?

@SteveBenson 2 жыл бұрын

No.

@karlbratcher6482 2 жыл бұрын

Yes. Calculate what your CO2 pressure needs to be based on keg temperature and desired CO2 volumes, e.g., 2.5 volumes at 70’F. At 70’F and 2.5 vol CO2 set your regulator at ~28 psig (from calculator). Roll the keg for 5-10 min or until bubbling clearly has ended. Put keg in refrigerator and chill completely. If you don’t chill the beer you run the risk of back flowing beer into your CO2 regulator. Hook up keg to CO2 line set at your desired serving pressure. For a refrigerator at 36’F and 2.5 CO2 volumes the regulator pressure set point is 10 psig. Serving line sizing should also be considered to control foaming. www.brewersfriend.com/keg-carbonation-calculator/

@AronOtterbo 2 жыл бұрын

@@SteveBenson So the beer is pre-chilled to serving temperature before doing this? Not coming from a previous video I dunno if that was clear coming from the previous video.