How to Change the Tire on a John Deere L110 Lawn Tractor
Пікірлер: 76
@robpurchia14642 жыл бұрын
Starter fluid trick was sick! Great straight forward video. Thx bud
@funbro12 жыл бұрын
It is kind of fun, dangerous so be careful if you try it, but fun. Thanks for watching.
@brianbrehmeyer39293 жыл бұрын
Thanks. I was having problems removing the rubber cap and wanted to make sure there wasn't something I was missing....Finished watching to the end. That is a GREAT idea, using the grinder to make the tire removal a lot easier.
@funbro13 жыл бұрын
Glad it helped, Thanks for watching.
@kennedymcgovern5413 Жыл бұрын
Now see, I have watched a few videos on how to do this, and this is the first one that is useful. Thank you. You see, as a teenager I worked in a garage. I KNOW how to change a tire. But what everyone else who made a video on this subject seems to overlook is the fact that i DO NOT HAVE a pneumatic tire press, nor a tire machine in my garage! Big ass C-Clamp and a grinder. Now those I have. Roger that, buddy. This will work. Thanks again!
@funbro1 Жыл бұрын
Glad you found this video.
@nickmikulak90059 ай бұрын
Great video but at almost 65 years old I just have to wonder why do you call a "c" clip an "e" clip but you still call a "c" clamp a "c" clamp... I'm hoping it's just to keep me from living another 24 days so I can say I made it to 65😂
@RojmaEsbog1 Жыл бұрын
Thanks for the video! One of my tires got damaged so I had to take off to go get a new tire. When I went to put back on, i noticed the small metal pin/key and was wondering what it was. The one the axle was turned it was upside down so I didn't see the slot. Your video made me realize what the metal key was for and how to properly put the tire back on.
@funbro1 Жыл бұрын
Glad it was a help to you. Thanks for watching.
@mikemcgown63623 жыл бұрын
Good video! I've seated beads without the fire, just a strap around tread and adjusting tire body while adding air. Most times it works.
@Stratsman233 жыл бұрын
You are a champion! I tried a strap and it worked great. I came here after an hour of mucking about trying to inflate the tyre. My frustrations were solved by your comment. Thanks!
@mikemcgown63623 жыл бұрын
@@Stratsman23 glad I could help. The shop I used to work at had a device that would shoot a sudden burst of air between the rim and the bead to seat it, but that was only for car and light truck tires. Like an air bazooka. It was kinda dangerous to use.
@funbro13 жыл бұрын
That way works but it isn’t as much fun. Lol thanks for watching.
@bonir014 жыл бұрын
Thanks for video, don't have the same rider, but helps understand how to change tire
@funbro14 жыл бұрын
Glad it helped, Thanks for watching.
@JonBecker814 жыл бұрын
So you don’t grind the new tire to make it easier to put on?? 😂
@funbro14 жыл бұрын
Not this time. Thanks for watching.
@metalshopfantasycamp1883 Жыл бұрын
The starter fluid to explode the bead in place is amazing!
@funbro1 Жыл бұрын
Yes, it is amazing however somewhat dangerous. Always be careful. Thanks for watching.
@misterh33 жыл бұрын
helpful, I like the idea of using the c clamp
@funbro13 жыл бұрын
Thanks for watching.
@stevenfry34424 жыл бұрын
Great video, thanks! My tires were severely misshapen due to being packed for shipping. To seat the beads, I had better luck leaving the strap off, then using the starter fluid.
@funbro14 жыл бұрын
Sounds good, for some reason I had to use the strap. Thanks for watching.
@stevenfry34424 жыл бұрын
funbro1 my tires came basically ‘folded’ into a box for shipping, so every time I would tighten the strap, they would collapse back into that weird shape. Couldn’t get the beads near the rim.
@kennedymcgovern5413 Жыл бұрын
Now for everyone: Be careful when you use this beading method. I used a strap to bead up a tire on a dolly recently. It WORKS. But...when you go to let loose that strap...it's going to pop back at you. It caught me in the thump and it was very painful. Just wear some thick gloves when you get to that part.
@funbro1 Жыл бұрын
Oh no, caution must always to be used with tires. Hope you’re OK, thanks for watching.
@williwonti5 жыл бұрын
Sometimes these rubber caps get hardened up a bit and it helps to warm them up before you take them off. A hair dryer or heat gun on low.
@funbro15 жыл бұрын
Good tip, thanks for the view.
@jameschanda87432 жыл бұрын
Yeees it worked boom!! Be safe all . Tie or anchor it to be safe
@funbro12 жыл бұрын
Yes, definitely be safe. Thanks for watching.
@codyjensen17732 жыл бұрын
Thanks, I got a 1970 John deere 110 and I’m restoring it and I got new tires but I’m only 13 so I’m not sure how to get it off thanks so much.
@funbro12 жыл бұрын
Glad I could help, Thanks for watching.
@bnhamilton3 жыл бұрын
Can you tell me exactly what kind of fluid you use? I have tried small engine starter fluid, and charcoal lighter fluid so far with no success. Should they work?
@funbro13 жыл бұрын
In the video it was Carb cleaner but starting fluid can also be used. ALWAYS use caution if you attempt seating a bead this way. Thanks for watching.
@donbailey66006 ай бұрын
I used starter fluid but all it does is set the tire on 🔥
@ToddField-cq3zj Жыл бұрын
How do you put a tire on a lawn mower rim?
@funbro111 ай бұрын
Watch the video?
@lonniecurtis3540 Жыл бұрын
hi bob i have a s130 has 20x10 rear tires,do you know if the rim is for the 20x8 -8,and if that size will fit them,thanks good video
@funbro1 Жыл бұрын
I'm not sure?
@lonniecurtis3540 Жыл бұрын
hi Bob I have some new tires 20x8-8,and jd said rim size is 8 inches width, should those work ,thanks
@kerns05jk5 жыл бұрын
Yea i dont remove the rim i just deflate the tire then drive the tractor to break the beed and the tire comes right off with the correct tire iron and the other one slides right over the rim with dish soap..use the weight of the lawn mower to take tire off rim...easy 5 minutes. Thats to much messing around with the rim. Work smarter not harder.
@funbro15 жыл бұрын
Sounds good, thanks for view.
@apathetic254 жыл бұрын
I drove around my backyard, then to my front, then up and down my driveway, and then back to my backyard, and then in circles. Nothing. I ended up just having my 350lb renter stand on the sides of the tire while it laid flat (after taking it off)
@glenwagaman91032 жыл бұрын
There's always one.
@TheOregonOutlaw4 жыл бұрын
Antifreeze to make rubber slide like fresh ice!
@funbro14 жыл бұрын
Nice, thanks for the tip and thanks for watching.
@bearbearjames Жыл бұрын
What size C-clamp are you using?
@funbro111 ай бұрын
I’d say about a 16 inch? Thanks for watching.
@Reallife3153 жыл бұрын
Stupid question but what does it mean to set the bead and what is the bead
@funbro13 жыл бұрын
The tire bead is considered the edge of the tire that sits on the wheel. to seat the bead means to "seal" or 'Lock" it into its correct position. Hope this helps, Thanks for watching.
@Reallife3153 жыл бұрын
@@funbro1 the correct position just means flush against the rim, all the way around, right? Welcome. And thanks for the info. Both of my tires have those dry cracks all over and are flat. I think I need new ones. They weren’t even that old lol
@funbro13 жыл бұрын
Yes up against the wheel. You should hear a bit of a pop when it seats.
@brianbrehmeyer39293 жыл бұрын
There are no stupid questions. (Not that you'd get that understanding from most KZfaq comments.)
@Reallife3153 жыл бұрын
@@brianbrehmeyer3929 true. I ended up completing this. And damn it was hard to switch those out lol.
@zeroturn70914 жыл бұрын
Are you using JD OEM replacements? I’m looking for a third party new set due to winter rot.
@funbro14 жыл бұрын
This tire was not an OEM. It was purchased online. Thanks for watching.
@TheOregonOutlaw4 жыл бұрын
Just got 2 from Amazon - $60
@poppyshoessp4 жыл бұрын
I was with you until you set it on fire. I'll leave that to the fellas. Thanks!
@funbro14 жыл бұрын
That was just the fun part of the tire change. Thanks for watching.
@michaeldiggs3009 Жыл бұрын
E clip is hard to get back on
@funbro1 Жыл бұрын
It can be difficult at times. Thanks for watching.
@MrKenmai515 жыл бұрын
You shoud use spray more soap lube so tire can go easy
@funbro15 жыл бұрын
As explained in the video, I like to use Windex because it lubricates enough but doesn’t leave a soapy film. Thanks for watching
@mightymightymightyman1993 жыл бұрын
Good video. Please, for the love of Jesus, do an update video where you clean the mower deck. That thing is DIRTY. No way to treat a John Deere...
@funbro13 жыл бұрын
If I do a video “How to clean the deck on a John Deere” would you watch it?
@mightymightymightyman1993 жыл бұрын
@@funbro1 Probably
@brianbrehmeyer39293 жыл бұрын
What's wrong with the mower deck? It looks just like mine. Lol...
@benb77272 жыл бұрын
For $20 more you can buy one already on a rim.
@funbro12 жыл бұрын
I wish. Thanks for watching.
@momoniu26894 жыл бұрын
any way to set the beed without igniting it on fire?
@funbro14 жыл бұрын
Large tire irons or a tire machine would work. Thanks for watching.
@jariousmitchell3 жыл бұрын
Why you aint just grind the old tire off lol
@funbro13 жыл бұрын
No reason. Thanks for watching.
@miguelangelvalderrama18084 жыл бұрын
Noooooooooooo😱😱😱😱man, how are you going to cut the old tire?????? That old tire should work as a spare, or for a go kart.
@funbro14 жыл бұрын
I am going to cut the tire as it had non repairable damage to it. Better to get a new one for the kart anyway. Thanks for watching.