How To Change The Track On Your Snowmobile! Step-by-Step

Рет қаралды 22,676

Күн бұрын

On today's to-do list we have to replace the track on a Polaris XC 700. Almost everything I go over on this video will be the same on other sleds! So don't let the fact that its a Polaris scare you!
Endless Ratchet strap that I used on the skid - amzn.to/3umogSL
Snowmobile Lift - www.extrememax.com/product-p/...
Snowmobile Dolly - amzn.to/3IUHbrN
0:00 Intro.
0:16 Game plan
0:39 Loosen the track
2:07 Compressing the suspension
3:08 Pulling the rear suspension bolts out
4:25 Pulling the rear suspension out of the track
5:35 Game plan for under the hood
6:32 Pulling the chain case apart
7:44 Getting the speedo drive apart
9:17 Getting the drive axle out
10:28 Removing the bearing from the chain case
11:51 Installing the new chain case bearing
13:39 Getting the drive axle ready to reinstall
14:37 Getting the drive axle installed in the sled
16:33 Buttoning everything up under the hood
18:30 How to get the suspension bolted back up in and outro!
Thanks for watching!!
Visit us at www.toyshop9665.com to see what were up to and to check out everything Amsoil has to offer!
Check us out on Patreon! www.patreon.com/Toyshop9665?u...

Пікірлер: 27

@rheidtech 2 жыл бұрын

Had to go thru 10 vids to find one i can use. Thanks for being real world. Great vid. Really.

@ToyShop9665 2 жыл бұрын

That means a lot thank you! I’ve got a lot of time in this so I’m glad it helped!

@markpinther9296 Жыл бұрын

Dude, seriously one of the most useful videos on how to do this that I have ever seen. Really appreciate you taking the time to make this video.

@ToyShop9665 Жыл бұрын

This is why I do it! Glad I could help!! 🤘

@jeffreyhagelin3672 Жыл бұрын

Excellent information, especially using the tie down strap to facilitate reinstallation. I found that if you measure the bolt hole centers from inside the tunnel, you can use that information when adjusting the tie down strap.

@joev467 2 жыл бұрын

Great video!!...Thanks

@Kent15156 6 ай бұрын

Nice video!

@donnieflame Жыл бұрын

Don't even have a snowmobile but now I know how to change the track! 😂 I'm Canadian and never rode one so I'm getting mechanically inclined before I get one

@ToyShop9665 Жыл бұрын

That’s actually a really good idea 😂

@sebrmz450 2 жыл бұрын

Nice video again! I'm new to snowmobile so that helps a lot! I would heat up the chaincase with a heat gun so the aluminum would expand.

@ToyShop9665 2 жыл бұрын

That’s a good thought! Heat up the chain case before putting the bearing in! It would help it slide in easier! Thanks for that!

@bhoss7133 5 ай бұрын

instead of rachet strapping the suspension, could i just remove a bolt from one end of the shock? (to allow the skid to collapse without force from the shock)

@ToyShop9665 5 ай бұрын

I might be nervous that then you’ll fight getting the shock back in inside the skid. Trade one difficult task for another. Try it and let us know!

@dbirdez 2 жыл бұрын

Next time you do a bearing , put the bearing in the freezer for a bit, use a heatgun on the race and it will pop in. Great video !

@ToyShop9665 2 жыл бұрын

Good idea!! And thank you!

@ChickenParm152 Жыл бұрын

ive broke 3 pairs of snap ring pliers trying to remove that snap ring... what tool are you using and what the trick to getting it out?

@ToyShop9665 Жыл бұрын

I pretty sure I had bought that snap ring plied kit off the Mac Tool truck. But it’s just a 90 deg snap ring plier. Nothing particularly special about it. Just make sure you’re using the right size.

@ChickenParm152 Жыл бұрын

@@ToyShop9665 yeah, i bought a good quality 45 degree set of pliers and it came right out. thanks!

@MumPyro 2 жыл бұрын

It's never a good idea to apply force to the inner race of a ball bearing. They are not thrust bearings and you can damage the ball cage inside. Anytime you're applying force to a ball bearing that you don't want to ruin it should be on the surface that is binding. In this case you should have had a socket or something that fit the outside ring of the bearing instead of the inside where its applying all of the force to the balls.

@ToyShop9665 2 жыл бұрын

This ☝️ I 100% agree with you. If this bearing would have required more force than it did to install I would have spent more time to find something to apply the force to the outer race. This was just a little quick thinking and it got the job done for me!

@darrylmarbut47 Жыл бұрын

Old vid I see but I thought same thing,good way to ruin it.