How to do a Whirlpool Washer Recalibration and More - Whirlpool Washer Troubleshooting Tutorial

Рет қаралды 226,327

4 жыл бұрын

If you replaced a part on your Whirlpool, Maytag or Amana Washer, you need to run a calibration cycle on the unit. But while you're in the "Secret" diagnostics mode, there are a lot of extra, hidden features you may not know about. You can test components as well to see if a part is going bad. But to do that, you need to bypass the lid lock to see inside! This video will show you how to do all of this. Timestamps for each thing are included in the video.
In this video, you should learn how to:
- Enter diagnostics to do a lot of important features
- Check Whirlpool Washer Error Codes
- Do a Whirlpool Washer Re-Calibration
- Test Each Part and Cycle in the Whirlpool Washer Troubleshooting mode(s)
- Bypass the Lid Lock (kind-of) to watch the drum move and operate to verify it works
P.S. These commands generally work on any Whirlpool-made device including Whirlpool, Kenmore, Amana, Roper, Admiral, Maytag and probably a few others (but not GE or Hotpoint!)
Parts Links for Major Failure Points:
Shift Actuator (F7E1, F7E5): bens-appliances.com/collectio...
Washplate Hub: bens-appliances.com/collectio...
Lid Lock (Maroon-Colored): bens-appliances.com/collectio...
Other Less Common Parts: bens-appliances.com/collectio...
DISCLOSURE: This post may contain affiliate links, meaning when you click the links and make a purchase, we receive a commission.
Affiliate Link & Earnings Disclosure: bit.ly/3oXeu3B
If you need to buy an appliance part to fix your washer, make sure to use Appliance Part Pro's model lookup system to get the EXACT part you need, to ensure it works - plus, you can return it if it doesn't fix your issue: bit.ly/3pVxWyX
Tools I use in all videos can be found at my Amazon Idea Page: www.amazon.com/shop/bensappli...
Did this video help you out? Send me a tip, and help me make more Appliance Repair videos for people to watch for free!
PayPal: paypal.me/BensappliancesYT?lo...
CashApp: $BenjaminSchlichter

Пікірлер: 132

@justhepainter 2 жыл бұрын

I had listened to several KZfaq sites explaining how to do a diagnostic/calibration procedure. Your's was Superior ! Thank you very much!!! You don't appreciate a washer 'til it stops working. Keep up the good work! Rob :-)

@mwcleaning 2 жыл бұрын

I caught it like another viewer. When going to calibration mode, set the light to rinse, not spin. Thanks for the video!

@Kelliena 2 жыл бұрын

This is amazing! Thank-you! Our washer locked but we reset it like you said and it unlocked!! fixed!

@markb1784 Ай бұрын

My problem: The tub would fill up, then sometimes the wash cycle would start. It never would enter rinse & spin . Then It would drain and the “wash” led would remain lit till I unplugged the machine. Your troubleshooting and recalibration video was easy to follow. It helped me understand the system and figure out that I needed a water inlet valve and an actuator. My machine also had a technicians guide in a plastic bag stuck to the inside front panel. With your video and the guide everything fell into place Thanks

@bensappliancesandjunk Ай бұрын

Nice! I'm glad this 4 year old video still has some relevance, hehe

@brucet12 2 жыл бұрын

Well put...your steps for diagnostic is great thanks

@leonardsolis9876 9 ай бұрын

The washing machine had the sensor stuck and didn't let me do anything . Thanks to you now I know why. Thank you!!

@mathewhunt81 Жыл бұрын

best video i have seen on this subject. great information and easy to understand. thank you for creating this resource

@MattFerguson26 Жыл бұрын

5:18 is exactly what I needed to know. My heavy agitate seemed so weak and could not find anything explaining this, my capacitor was bad. Replaced the cap, and like new again!

@homeguestunton Жыл бұрын

0:08 The washer in this video got bad bearings it seems like.

@HazyShayd 2 жыл бұрын

Immensely helpful in testing my drain motor after cleaning out sand. To others with this model: My unit will only run a normal cycle with 1 Rinse selected; I tried everything except replace the board - so that's either a workaround that might be helpful to you (just stink to 1 Rinse), or a cry for help (Anyone know why?) depending on where you stand.

@homeguestunton Жыл бұрын

Also those bearings are definitely bad. I heard them in the sensing cycle. I mean this is a 2013 back when Whirlpool was known for this.

@keaaul808 2 жыл бұрын

Very helpful, thanks! In cal mode, you mentioned spin, but instead positioned the knob in rinse.

@joeskodny6205 2 жыл бұрын

Yes I caught that too. So do we put it in 'rinse' or 'spin' mode?

@kellyfrost7258 Жыл бұрын

It's RINSE. I have the service manual and have seen other videos say rinse.

@dxnxix579 3 жыл бұрын

Thank you this was super helpful 🙏🏼

@bensappliancesandjunk 3 жыл бұрын

Glad it was helpful!

@LuckyDogDog 3 жыл бұрын

Hello and thank you for making this video my question is why will my machine not fill up all the way with water when it's on deep water wash

@davidveneruso2860 11 ай бұрын

Thanks, you are very helpful

@kandychic1 Жыл бұрын

@Bens Appliances and Junk Hi my whirlpool washer fills, washes then drain. After that it's stuck on the rinse light without spinning after draining from the wash cycle. What do you suggest might be the problem and how can I fix it?

@anibal2476 2 жыл бұрын

After doing the Auto test, the Cold inlet would not open. I'll take the assembly out for inspection shortly. Hopefully this is the only issue, since I don't have a multimeter to check for opens. I wish wringer washers would come back (manual, mechanical control for me to monitor).

@resurgensix 3 жыл бұрын

Great vid! Thanks!

@bensappliancesandjunk 3 жыл бұрын

Glad you liked it!

@lucasgregory152 5 ай бұрын

Hey! Not sure if this will be seen but worth a shot. I have the exact same model as this, and just did the test and the agitation isnt happening at that step, its making the regular noise but not moving. Sooo..yoi mention either the motor or capacitor is bad, so the million follar question is how can i determine which os at fault? Thanks so much, great video

@laurenclark8615 3 жыл бұрын

how do i change the lid lock thing? mine is sensing, filling up with water & then just stopping.

@dionstephen88 2 жыл бұрын

my crosley does not agitate, agitates one time slowly counter clockwise and then pauses then one time counterclockwise as you suggested should i change capacitor first.

@christopherwatson283 2 жыл бұрын

Did You check for Money under the Agitator? I'm not seeing the Tub Rods wearing out. Maybe the Springs. Cool Vid. Mines a 588-20 which is Newer. I have had some leakage I think is related to getting out of balance. I couldn't find anything wrong except the Money(Dimes) under the Agitator. God Bless, C.

@troymorris3841 4 жыл бұрын

Anytime am using my whirlpool washing machine it is letting out the water an it is not washing,Why is that happening?

@jessicadlicea 3 жыл бұрын

Thank you for making this video. On the calibration you say turn to fourth light spin but in the video you stop at rinse, which is correct?

@jaemielee_mc1053 4 ай бұрын

Rinse is recalibration mode..3yrs an no answer..u must have thrown out ur washer by now or someone else's video helped u out

@zyd7047 2 жыл бұрын

Thaks sir

@IgorMopoz Жыл бұрын

Hi; My machine won't start, and when I do test, the "done" indicator is not illuminated at all but others are; what would be wrong? Thx.

@Newberntrains 4 жыл бұрын

I own a 2019 maytag (ui looks identically) and was wondering the calibration what does it do for the washer and how would i know if its needs it

@bensappliancesandjunk 4 жыл бұрын

Generally, calibration is only needed if you had to replace a component on the washer such as a mode shifter, suspension rods (for re-balancing), motor, or other major components. Some newer washers already re-calibrate if a new component is installed, but I am unsure if a 2019 Maytag would need it.

@kalehallman Жыл бұрын

Great videos, I refer to your channel quite often. I have a couple of questions: When running diagnostics, do both hoses need to be connected to the washer? If so, does one HAVE to be hot or can they both be cold? When checking codes, why do I sometimes get the same code twice in a row with the only difference being that I get the “done” light at the end of the E code on the second code?

@bensappliancesandjunk Жыл бұрын

Depends on diagnostics. As long as you aren't doing auto-test, you don't need hoses at all. We often run them without hoses just to test the essentials like lid lock / spin. You can run cold/cold on a Y-split without issues just fine. On the codes, its probably adding a +1 on it as a variant. Like on a lid lock error, it could be a fail state for both on and off, or a shift actuator + motor code.

@kalehallman Жыл бұрын

@@bensappliancesandjunk ok. I wasn’t sure if part of the diagnostics was to test the thermistor. If it isn’t obvious, the machine I am working on is my first machine (other than my own machines). I never knew there was a diagnostics and error code function until recently. Thanks for your help.

@tomk4092 9 ай бұрын

Tried this- the washer just about got airlift while in spinning part of calibration. What would that point drop? Original problem is that it doesn’t drain on spin mode completely. Not a draining issue.

@ohthatsdiana 2 жыл бұрын

Can I get a link to buy this washer ?

@gregzucconi2005 8 күн бұрын

My whirpool goes from sensing and when it switches to wash it just stops. Cant seem to figure out the issue

@zacharycrawford6519 8 ай бұрын

Diagnostic doesn’t work.

@corneliusramela4585 11 ай бұрын

I have a digital whirlpool washer, how can I reset the machine? Thanking you in advance, regards Cornelius

@lecovio 3 жыл бұрын

I am working on a washer that after spin mode instead of doing to done, it starts a new cycle by itself all over again

@bensappliancesandjunk 3 жыл бұрын

Extra Rinse selector on?

@johncosta787 3 жыл бұрын

After replacing the shift actuator Is it necessary to re-calibrate the machine or can I just replace the part and plug and play

@bensappliancesandjunk 3 жыл бұрын

I'd suggest recalibration just to stay safe

@juanitakise9173 4 жыл бұрын

i have had a Amana washer similar to this, i've got the code to start the machine but after i get it to start washer, when do i put the desired style? I mean "med, heavy, delicate etc..I don't know why they started making all wshers like this? we ought to have choices as a digital one or a regular one we use to have

@bensappliancesandjunk 4 жыл бұрын

if the machine is unplugged, once its plugged in, give it about 15 seconds to boot up. From there, you can rotate the knob to select whatever clothing mode you want to use. Once that's done, press start and it should run the mode you selected.

@prestonbertrand2636 10 күн бұрын

My kenmore 500 series won't calibrate in rinse.

@troymorris3841 4 жыл бұрын

So after doing all of that anytime you are going to use it do you of to go through that process?

@bensappliancesandjunk 4 жыл бұрын

No. Just do it once when you replace a part to calibrate the machine.

@lvl88661 2 жыл бұрын

yes this new models are a "piece or crap , but its is what it is man , good video 👍

@nicolerichey8513 3 жыл бұрын

Any suggestions my washer leaves my clothes sopping wet at the end of the cycle and when it spins it makes loud noises . I tried to run the calibration mode and had to unplug it because when it got to the spinning part it started getting so loud and moving all over the place kinda made me nervous . Also when I hand push the drum is makes a squeaking noise when I movie it horizontally thanks greatly appreciate some advice

@bensappliancesandjunk 3 жыл бұрын

Likely suspension rods are going bad making unit bounce around. Most newer washers will detect the washer banging around and error out of higher spin speeds. If its a whirlpool, I do have a video on changing the rods out.

@pamelawest2316 Жыл бұрын

I have a Kenmore 600s he, had banging and walking on spin and error Ofb…suspension springs didn’t help, replaced drive assembly didn’t help…what else can I replace my unit is only 4 years old…going to try the test for faults…would appreciate your input, Thank You

@lilreb720666 4 жыл бұрын

Do you have a video for UI test mode?? It seems my dial doesn't quite line up with what I'm trying to do

@bensappliancesandjunk 4 жыл бұрын

Argh, I dont think I do yet. What are you trying to do?

@lilreb720666 4 жыл бұрын

I have been having issues with repeating cycles and there are times I try to set on drain and spin or rinse and spin

@dominailtion 3 жыл бұрын

Did you replace the rear suspension rods or are they still broken

@bensappliancesandjunk 3 жыл бұрын

Oh, we replaced them a long time ago.

@stevenandrade973 3 жыл бұрын

I have a whirpool similar to this and the lid got opened during spin. Now the llid lock just clicks and the machine won't do anything. How do I know if its the lid lock or the latch itself

@bensappliancesandjunk 3 жыл бұрын

I imagine its the lid lock, but put it into diagnostic mode and see if you can test the lid lock / see if any related codes to the lid lock pop up.

@dianareyes8774 9 ай бұрын

If that’s not the problem for an unbalanced washer, what can it be?

@matasiward3305 Ай бұрын

whirlpool washer going from sensing to done what does that mean

@EnvyTheRealest 2 жыл бұрын

I can't the washer after the all this instructions is completed. I'm ready to wash some cloths and it does not start

@littleburnrrrgaming Ай бұрын

I put that for service mode

@unclefester9113 Жыл бұрын

And ... silly me thought the only trouble I had was broken leveler legs. I'm going to bet that I have at least one broken leveler PLUS... the suspension problem shown. Now the question is - do I just spend $$$ 500 plus for another machine .... or spend a hundred bucks for parts and take a chance?

@kalagill6071 3 жыл бұрын

After cycle is done on my washer is will start over and I dont catch it in time and lid locks. I tried recalibrate it but I didnt help. Please help.

@bensappliancesandjunk 3 жыл бұрын

Do you have it set to extra wash or extra rinse?

@JSmith-Not-Smythe-Dear Жыл бұрын

The model number for this Whirlpool washing machine is WTW4900XW0.

@putheflamesoutyahoo1503 6 ай бұрын

rinse cycle test ok....but wont rinse when washing

@davidlingenfelter2916 3 жыл бұрын

AT 7:25 in the video you say to "select the fourth mode labeled spin", but you select rinse. Just a slip of the tongue?

@bensappliancesandjunk 3 жыл бұрын

yep

@derekhughes5220 3 жыл бұрын

Is there a trick to get it to go into calibration mode. I try to spin the dial but the lights will not light up.

@bensappliancesandjunk 3 жыл бұрын

Try it slower on turning the dials. Usually I try it "Fast" once, then "Slow" and usually one of the two cadences work

@edgardosabinay1138 2 жыл бұрын

I own kenmore 500 series and replace lid lock,I did calibration but my washer still stuck on rinse and flashing...do you think I need a new control board for my kenmore?

@bensappliancesandjunk 2 жыл бұрын

What other error codes came up?

@edgardosabinay1138 2 жыл бұрын

Since I replace my lid lock,I don't have codes at all,I did disconnect, reconnect all plugs but still stucks at rinse and flashing!!

@bensappliancesandjunk 2 жыл бұрын

@@edgardosabinay1138 make sure to recalibrate the washer, that will reset such a situation possibly.

@edgardosabinay1138 2 жыл бұрын

Yess I will,thank you much!

@corneliusramela4585 11 ай бұрын

My washer starts automatically when I plug it in ?? How can I reset it?

@ginabee 3 жыл бұрын

I’ve had my strike plate off since day 1, but I’d like to be able to close the lid flat while it’s running. Is there any solution that leaves access to opening during the wash cycle without the door locking? I hate this thing! X)

@bensappliancesandjunk 3 жыл бұрын

No. The lid switch is a pulsed-cycle on/off. The computer needs to know it can lock/unlock as needed, so there's no basic bypass

@ginabee 3 жыл бұрын

@@bensappliancesandjunk Thanks for the reply. I’ll stop searching for a workaround and try to get used to it locking up my clothes. :). I like having control :). I can’t get used to not being able to soak things overnight either. Damn, I’m sounding like an old woman lol 😝

@bensappliancesandjunk 3 жыл бұрын

@@ginabee interestingly enough, people hate the "feature" so much they've changed the newest washers to let it unlock during wash and only lock in spin mode.

@ginabee 3 жыл бұрын

@@bensappliancesandjunk Ahhh! I just got this one 2 months ago LOL

@bensappliancesandjunk 3 жыл бұрын

@@ginabee odd. All the new ones I thought had the unlocking during wash

@chiyuryuu2687 4 ай бұрын

I’m sure you tried but it needs more clarification and time stamps. I just got a bunch of green lights flash to the left.

@pootsalapp 3 жыл бұрын

Hi Ben. I have a Whirlpool WTW5000DW washer. In initial water fill mode it fills for 10 seconds, then agitates(full clothes load) then stops and fills for 10 seconds. This continues on and on. Checked and cleaned inlet filters. Water pressure is great and hoses are clear. Any help is appreciated.

@bensappliancesandjunk 3 жыл бұрын

Did you find any error codes?

@pootsalapp 3 жыл бұрын

@@bensappliancesandjunk Yes, F9 E1. At that point it was stuck in spin cycle. Now it’s not filling. Seems to be issues all over. I’ve checked discharge hose and height, no issue there. It’s my sons machine, so I have not rechecked.

@bensappliancesandjunk 3 жыл бұрын

@@pootsalapp that's a drain pump code. Check and replace drain pump.

@pootsalapp 3 жыл бұрын

Thank you for your help. Ran load through, completed spin cycle but there was a humming noise, maybe the pump, after spin. It ran for about 15 minutes before I canceled and took the load out. I had previously checked pump and hoses. The impeller didn’t spin freely, more like a half spin then some tension, then spin and tension. Think it’s the pump?

@bensappliancesandjunk 3 жыл бұрын

@@pootsalapp f9e1 is for a pump or drain related issue. If it drains fine, then I'd recalibrate and run a load thru it.

@sirmi9868 2 жыл бұрын

It just turn off when i try to calibrate it

@DavidSmith-le4qe 9 ай бұрын

Washer enters calibrate mode does a couple things for a few seconds and then just stops. No corrections made.

@aliciageorge3740 3 жыл бұрын

I attempted to put my whirlpool washer into calibration mode, did the same left turn, 3 right turn, left , then right. All lights blinked then i clicked to rinse n pressed start. However its been hours literally like overnight, woke up n the lights still blinking around. Sighzzz HELP please.

@bensappliancesandjunk 3 жыл бұрын

Press and hold cancel for 3 seconds to reset it

@lithiumlounge Жыл бұрын

Diagnosed mode will not work for me

@coolrobuxgaming 11 ай бұрын

That bearing is definitely bad. Also the suspension looks bad too.

@johnniemccracken231 Жыл бұрын

My whirlpool washer still drips cold water after finishing. What can I do?

@scottfrbbdjr 2 ай бұрын

Most likely your water inlet valve for your washer is shot, and will need to be replaced

@bahamas242able 3 жыл бұрын

I did all of that and still having the same issue

@bensappliancesandjunk 3 жыл бұрын

What's the issue?

@bahamas242able 3 жыл бұрын

@@bensappliancesandjunk when I start the washer the sensing like would turn on, the lock light would turn on, then unlock, then lock, water comes out then nothing happens

@joshuaworden5571 2 жыл бұрын

Whats the model number of this washer?

@spasticbrit Жыл бұрын

WTW4900BWO

@joshuaworden5571 Жыл бұрын

@@spasticbrit thank you!

@littleburnrrrgaming Ай бұрын

2:45

@hanks-dances-stuff 2 жыл бұрын

1:30

@troymorris3841 4 жыл бұрын

I just watch this video so now am going to try an wash some clothes now....

@homeguestunton Жыл бұрын

It seems like the bearings are going bad on it too.

@homeguestunton Жыл бұрын

It definitely needs new suspension and bearings. Those are shot.

@gerryomo9515 2 жыл бұрын

None of these tips are working. As soon as I turn on the machine it goes into draining mode even I’m trying to add water.

@christinebundy495 10 ай бұрын

My water stops before the machine is filled

@SteveXNYC 2 жыл бұрын

The machine took 3 hours to wash a load of clothes that takes 30 minutes by hand wash. WHIRLPOOL da SH*TPOOL

@gregorywells4423 Жыл бұрын

Bought one 1 yr. Ago....NEW...NOT WORKED RIGHT FROM DAY ONE.....JUNK !!!!

@wrbwn 2 жыл бұрын

Thanks for this video. These washers are a piece of junk.

@Iriea09 2 жыл бұрын

Never buy a whirpool washer! It's a peice of junk. I bought a brand new one and the thing just would never finish a cycle. Yes. I check the water valve. Yes. I recalibrate it. This thing is a piece of junk!

@lewisgoodleaf1979 Жыл бұрын

THE BODHI 12345

@mowgli83070 15 күн бұрын

YOU dint test any components the machine did. I'm guessing you don't understand what I'm saying and you don't know gow to actually test individual component

@bensappliancesandjunk 14 күн бұрын

I have dozens of other videos showing that. This video was made over 4 years ago. I realized that more videos were needing to be made with more tests so there are many, many more videos to pick from

@bassman-mv2ry 4 жыл бұрын

great info but you talk way to fast and dont list exactly what is needed we are not all experienced techs and had to watch multiple time to get the info right, ssssssssSLOW DOWN and explain steps BETTER!

@bensappliancesandjunk 4 жыл бұрын

This is an earlier video I did, and I've tried to slow down what I say on future videos. KZfaq doesn't let me edit or alter the videos in any way so I can't go in and re-do sections unfortunately.

@jameswalker590 3 жыл бұрын

It's a free video dude. You take free advice how it's given to you. The fact that you're getting advice from someone who knows what they're doing is a blessing. Pay a repairman if you can't understand or are unwilling to rewatch a few parts.

@nynysworld1429 3 жыл бұрын

Cry baby

@tlroy 2 жыл бұрын

You can adjust the playback speed when watching a KZfaq video. I use the function all of the time.