How To Install a Direct-To-Stud Shower Enclosure

How To Install a Direct-To-Stud Shower Enclosure | The Home Depot with

Рет қаралды 596,558

Күн бұрын

Learn how to install a shower surround directly to wall studs with ‪@thisoldhouse‬. A bathtub and shower combo is a great addition to your bathroom, and installing a direct-to-stud shower surround is a project that you can complete in under one day. Take careful measurements, dry fit your shower surround to ensure the right fit and then install the panels. For more related videos, see our DIY Bathroom Renovation Ideas playlist: thd.co/3xdiukd
Visit our How to Install a Direct-to-Stud Shower Enclosure guide for more details: thd.co/3iQ26kk
Follow the steps below to install a direct-to-stud shower enclosure:
0:00 How to Install a Direct-to-Stud Shower Enclosure
0:24 Prepare the Shower Area
0:50 Pre-Fit the Shower
1:28 Install the Base
3:20 Insert and Attach Back Panel
3:53 Insert and Attached Side Panels
4:07 Install Plumbing Panels
4:37 Install Trim Kit for Shower Valve
Find even more DIY project ideas from The Home Depot: thd.co/DIYGuides
#TheHomeDepot #HomeImprovement #DIY
SUBSCRIBE to The Home Depot: thd.co/2iib0HE
About The Home Depot:
How doers get more done. We’re helping doers in their home improvement projects. Now you can take on more renovation projects with more know-how. Our step-by-step instructional DIY videos and expert advice will give you the confidence for your next project with hands-on learning. It’s a good time to be a doer.
Follow The Home Depot:
WEBSITE: thd.co/TheHomeDepotSite
FACEBOOK: thd.co/TheHomeDepotFacebook
TWITTER: thd.co/TheHomeDepotTwitter
INSTAGRAM: thd.co/TheHomeDepotIG
PINTEREST: thd.co/TheHomeDepotPinterest
How to Install a Direct-to-Stud Shower Enclosure | The Home Depot with ‪@thisoldhouse‬
• How To Install a Direc...

Пікірлер: 74

@ydfah Жыл бұрын

A pretty good demonstrations with a few notable exceptions. Sheetrock screws are not galvanized and rust, so using them in this situation especially up at the shower arm fitting for support is just wrong. Also, when gluing the PVC drain, I didn't see any purple primer being used. When the drain and valve trim plate were being installed there sure was a lot of debris that should've been removed first. Finally, after setting the base into mortar, place about 40 lbs. on center of it and let it sit overnight. The weight will keep the base from lifting or shifting while the mortar sets.

@dillondoty1346 Жыл бұрын

Make a video or shut the fuck up

@glock316 9 ай бұрын

What screws to use instead of drywall screws ?

@ydfah 9 ай бұрын

@@glock316 First I pre-drilled my holes in the shower mounting lip, and then I used #8 x 1-1/4" truss head screws, they were Teks #21512 from Home Depot.

@Auxik 8 ай бұрын

The purple "primer" is just pipe cleaner. It isn't necessarily needed for new PVC. But great point about the galvanized screws.

@stevelabranche6119 7 ай бұрын

Thanks guys. I've learned more in these comments than 3 video's.

@LikeNoOtherPlumber 2 жыл бұрын

Highly recommend to remove cartridge inside valve before soldiering😮

@amosperry5737 2 жыл бұрын

Not bad

@nova31337 Жыл бұрын

This was nice. Love seeing 'ol Tom Silva. Hope he's doing well these days.

@richardferguson8217 Ай бұрын

Good content and good advice. With regard to the single handle shower valve, I suggest removing the cartridge from valve body to prevent heat damage to the cartridge when you solder the connections. When you re-install the cartridge, sparingly apply silicone plumbing lubricant to it to make it easier to insert in the valve body. Keeping the cartridge in a plastic bag will prevent it from being contaminated by construction debris.

@killerbunny3192 Жыл бұрын

great video clean helpful to the point!

@catfish24 4 ай бұрын

It's very important to use pan head screws because any other type of head on the screws will split the fiberglass when tightened down.

@williamrosado5746 2 жыл бұрын

I have the exact same system and shower drain can I use the shower drain with 2" copper drain pipe?

@Video17943 7 ай бұрын

Good information I need to buy the kit

@elmermt 4 ай бұрын

For this model can you install a foldable teak bench or seat. on the wall?

@govercheck 7 ай бұрын

Hi, I know it's 2 years ago but should you screw in the base? My instructions says to screw in the base and supplied the screws for it. I have sand mix all under mine and it's solid. A friend of mine was saying don't put the screws into the base you don't need plus it could add tension and crack. Thanks

@BC-ni3sk Жыл бұрын

Perhaps a critical step, how to remove and then install a new drain in the pan.

@AnonyMous-yb7cp 11 ай бұрын

Thanks for this video

@user-qy2nb4vd2s 4 ай бұрын

If the shower is on an exterior wall, do you need at add wall board behind the enclosure ? Or do you still screw to the stud ? And how thick is that vapor barrier ?

@garyczerkies6924 2 жыл бұрын

I am installing the sterling 4 piece 48" shower, do you need to install a 2x4 support block between studs to support the valve and if so how do you determine the distance so that the bonnet comes thru the panel far enough for the trim. the valve is a delta multi choice with plaster ring

@Parabellum-X 2 жыл бұрын

It is best to use a 2x8", or some 2-by that is wide enough so that you can mount the shower valve body onto it. I attached my 2x8" to the studs first (like a fireblock) with a few screws - making sure to install it at the same the height of your valve body that you desire. Experts say the valve body is supposed to be mounted between 40"-44", but you can install it anywhere you want. Just remember: your chosen location is going to be permanent, so I recommend placing it as close to the center of your shower base as possible. Then I simply used a couple of more screws to mount the valve body onto the block of wood. Your valve body should have come with a square plastic piece (mine was black) that you temporarily attach to the valve body. Attach that onto the face of your valve body in order to see where you're finished wall is going to be located around the valve body itself.

@juliancardoza7052 2 жыл бұрын

Showerhead replacement valve

@MrMel4me Жыл бұрын

You didn't say anything about when to remove the black plastic housing on the new faucet.. does it stay on or do you remove it at some point?

@MoroMoro1 2 ай бұрын

Is it right to install the plastic over the insulation that has the paper backing on it??

@eddyf1269 Жыл бұрын

Where is the link to the item on the video?

@ralphcintron6195 2 жыл бұрын

you dont have to put some type cement board or durrock behind the enclosure for mositure? thanks

@charliejohnston1978 Жыл бұрын

I would do everything possible to ensure a water tight enclosure, including vapor barrier and sheet rock. anything and everything to stop and slow a leak.

@ivettesantana4319 6 ай бұрын

thats what am thinking too. What if the pan cracks. Our shower wall is cracked but it also seems from the 80's@@charliejohnston1978

@lesleygaither1 2 жыл бұрын

Why don’t they make the tub lip slant so it won’t hold water? This is a problem for me. I have to use a paint scraper covered by a rag to clean it out. Pink mold grows there.

@DirtyOne614 9 ай бұрын

Because your shower isn’t level

@hadtocheathimtobeathim6549 6 ай бұрын

Because the walls sit on that ledge

@junky9 2 жыл бұрын

Looks like he's using sheet rock screws.. big no no.. pan head screws are required

@sirvayr Жыл бұрын

I have my doubts with that drain/gasket combo?

@RachelFu-ism 2 жыл бұрын

Where can I buy those clips at 1:57?

@MikeNRoll808 2 жыл бұрын

They usually come with the shower base.

@BrianBerriosOne 2 жыл бұрын

The Home Depot.

@dannyreed447 Жыл бұрын

What kind of screws do I use to install the same shower

@brendsjohnson4589 Жыл бұрын

Galvanised screws and nails are zinc coated nails that have undergone a galvanisation process. This process means the nails have a protective barrier which makes them resistant to rust and corrosion.

@charliejohnston1978 Жыл бұрын

@@brendsjohnson4589 Many zinc coated nails and products are not galvanized, and besides they do rust after several years anyway. Use stainless screws only. QED

@carlthornton3076 2 ай бұрын

Very Good!... #68 {4-26-2024}

@SticksAandstonesBozo 10 ай бұрын

27 years Building and remodeling homes. I’ve never , not once seen or heard of setting a 3 piece pan in mortar. 😂

@stephen9546 Ай бұрын

Do you use hot mop/ asphalt

@Didleeios88 2 жыл бұрын

How do you prevent water from getting into the gaps between the panels? I'm looking to replace a moldy shower and don't want to end up with the exact problem on a new one.

@MikeNRoll808 2 жыл бұрын

I usually caulk the vertical lines with silicone (make sure it's rated for kitchen and bath). The horizontal gaps are usually left uncaulked or caulked as shown in this video.

@USAFTACP 2 жыл бұрын

Most caulkless surrounds guide the water down to the pan allowing it to drain.

@Parabellum-X 2 жыл бұрын

I agree Blitziel, but I would still use a thin bead of silicone anyway, as an extra security measure. I don't even want a single molecule of water slipping through. 😏

@nova31337 Жыл бұрын

@@Parabellum-X The problem is that over time the caulking can break down or a tear or gap develop from use. Now the lip of the pan is most likely sucking up or holding water instead of letting it freely drain and air out.

@jose2226 Ай бұрын

@@nova31337so the question is, to caulk or not to caulk?

@DopamineOverload 2 жыл бұрын

So there is no need at all for backer board or GoBoard? I can't seem to find an easy answer to this.... thank you!

@michaelbluejay 2 жыл бұрын

It depends on the specific model. Some are direct-to-stud, some must be installed over a solid wall.

@DopamineOverload 2 жыл бұрын

@Sam Ram Appreciate it. We put some at the top and then painted over it. Looks good... just to be on the safe side I guess. Thx for your reply!

@ivettesantana4319 6 ай бұрын

thank you for your answer. am here looking because this direct to stud is scary.@@michaelbluejay

@emericanmm 2 жыл бұрын

Why were copper and solder used, here? Isn't it easier and more cost effective for a homeowner to use PEX? Or at the very least use SharkBite fittings?

@jimthompson909 2 жыл бұрын

Agreed!

@heimburgchr22 2 жыл бұрын

It’s my understanding that solder is best (when done right), especially for locations that are difficult to access like tub/shower supply lines.

@JUICE-wk2tz Жыл бұрын

Pex and expansion rings are great and very cost effective, but SharkBite fittings are expensive (about 8x the cost of copper sweat fittings) but imo really shouldn't be installed in areas with no access, the plumbing company I work for in NJ won't allow SharkBite to be used for anything except to cap off stub outs, and never concealed inside of a wall. But that being said, I'm sure when properly installed (prepping the pipe/deburring) and strapping/securing the pipes properly, you'll probably be fine with sharkbite lol but lots of people just cut pipes and slide sharkbites onto them and call it a day lol

@williamlevinson3001 10 ай бұрын

@@heimburgchr22ft.

@williamlevinson3001 10 ай бұрын

@@heimburgchr22SW OCSA asked the

@trendzpainting Жыл бұрын

You didn't acoustic seal the vapor barrier at the bottom???

@sylviamendoza1906 Жыл бұрын

What type of moisture barrier was used in this video? Is there a link of where to purchase some?

@ivettesantana4319 6 ай бұрын

all i see is that plastic film which scares me lol

@catfish24 3 ай бұрын

It looks like just regular plastic sheets that you can get at Lowes, Home Depot.

@charliejohnston1978 Жыл бұрын

Smart people do not use water based paint around water at all, unless they just like to repaint every couple of years.

@catfish24 4 ай бұрын

Oil base paints Attracts mold and mildew . Latex or water base paints do not.

@whyyouasking9744 2 жыл бұрын

Keefui inpekte shawa

@jdsbeau1 2 жыл бұрын

ha - who has all these special tools ?

@danshkorov6700 2 жыл бұрын

Most of the tools are pretty common or cheap to buy. The inside cutter is like 10 bucks. The only thing that's expensive is the copper crimpers but you can just solder instead.

@labelskater613 2 жыл бұрын

A drill bit and a drill. Just use shark bites instead of soldering

@jaywalsh1329 2 жыл бұрын

I happen to have a press tool available to me. Quite awesome, although, I only need to cap off the old tub sprigot, and extend my shower head up higher, so I'll probably just solder. I don't trust shark-bites inside a wall. I used them in my basement though, where I have acess.

@ADappreciation 2 ай бұрын

Good lord could this be more f---ing complicated? Is there really no way to install a shower with 80 moving parts and so many points of failure down the road? It's showers like these that create a market for shower replacement kits

@gunnyrohn882 19 күн бұрын

I didn't see anything complicated.