After watching your tutorial I thought I`d give it a try . Contacted Bum and ordered 3 samples . Picked the "Ed Sullivan pearl" and gave them my sizes . Had the wraps in less than a week !! They were cut perfectly for every drum. I wanted a Ringo looking set and they look FAB ! Installation went really well because I followed your instructions to a tee. A huge thanks to you and Bum Wraps (they were great) I finally have a great looking Ringo set without spending a small fortune . Love your videos !

From my experience, the best thing to do when making the holes for the lugs is to drill with a smaller drill bit first from the interior of the shell into a small block of scrap wood on the exterior of the shell to prevent the wrap from lifting, and not applying too much pressure , drilling slowly , going in a little a time, taking your time.. This will give you a nice and even hole with no lift.. This process should be done when the high bond tape has fully cured to the seam, which would be about 24 hrs.. For smaller drums like this 12x8 tom, the best thing would be to poke a whole from inside of the shell with either a thin screw driver, or thick nail to act as a guide, then drill from the outside of the shell into the interior of the shell..Or you can use the same procedure as i stated earlier, but using a small hand drill.. It's a lot faster, safer for the protection of the wrap, and will look factory..

Hey Randy great tutorial and you make it fun to go with you on the journey of rewrapping our drum kits. Also thanks for the information on finding a place to get the wraps and specialized wraps. Thanks again Randy...🥁🤘🥁🤘🥁😎

Followed your techniques and got great results- thanks very much. My vintage Rogers kit looks awesome.

WOW, they look GREAT. You did a really nice job. Good video too. Can you post a few pictures of the other sets you wrapped after these? I'm anxious to try it. A good friend (drummer) and I (not a drummer) just hand-sanded, wet-sanded, power compounded and power polished every single scratch, nick. scuff and buff mark out of a set of five 1976-77 clear Vista-Lites, inside and out, (and polished all the chrome too). Almost anything would be a faster reconditioning job than that. It was messy too. This looks lots faster for his "next project".... and we're all "practiced-up".

You crack me up man! Loved the video. Thx

Diggin' this video. Nicely done.

Looks great!

Drums are fun. I really enjoyed the video. :D

Thanks for posting. Love the detail; and the black hardware. Add black tension rods though! That would drive me nuts, having chrome and black together. But I'm nuts anyway, so... so nuts I refinished all of my hardware using truck bedliner for a cool, durable, and textured matte look.

Things i do before dis-assembling the drum: If it has a mount on the drum mark where the mount was on the inside of the shell with a pencil. Also mark where the badge was on the inside of the shell and make the mark an arrow letting you know if the drum is up-right or upside-down (Most of the time you can tell this by where the air hole is). Clean shell of any tape or glue that might be left from the old wrap using a razor blade just scrapping the shell shaving it. Measure where the badge holes were if your badge uses screws. Use a small bit in an dremel tool for your badge holes once the wrap is on. Wrapping: I trim my wrap 1" longer then required to go around the shell. I do a 1" seam and start my wrap on the back lug holes. Use a straight edge to pencil a line across the shell where you need to start your wrap and an arrow directing you which way to wrap it. I use the white 1" double-sided film tape on the shell first putting that tape where you penciled your straight edge line (This keeps the wrap on the shell for you to get nice and tight instead of using clamps) . Then once the wrap is around the shell nice and tight i use the red 1" heavy-duty double-sided film tape (solvent acrylic adhesive) on the wrap. No need to glue a seam with thin wrap. If you do have much thicker wrap i do all the same process but just not the red 1" heavy-duty double-sided film tape on the wrap seam instead i rough it up a bit with sand paper both parts of the seam and apply 3M 30NF neutral adhesive contact to both parts of the seam let dry and stick it together using a j roller. Prepping for assembly: I use an awl from inside the shell and as you're poking the holes hold a small block of wood on the opposite side of the holes so the awl doesn't just poke all the way through the holes lifting up your wrap. Then use an cordless drill with a step bit going inside the holes from outside of the shell. Perfect holes and if you wanted even cleaner use exacto knife afterwards to clean the holes up but it's not needed since the lugs hides any of that anyways.

My main acoustic kit has wraps from jammin sam from about twelve years ago, no complaints.

what a great finish! brilliant tutorial randy, very informative!!

Looks really good! I want to see how the seam looks like with the hardware on the drum though!

Yeah looks good, I might just have to get some when I have the money. I like the way my set looks now but something more original couldn't hurt.

I like this guy.

How much distance should there be from the edge to the wrap? I've seen other videos where they take the wrap right to the edge.

Very cool, bro! Stumbled across this video and was like, "That looks like Randy!". lol Well, there you go.

Hi. Where I can get the drum wrap, I'm interested. That material is? is something really gross? @Vanz Drumming

I recently got my snaredrum wrapped with a Pokémon finish.. looks pretty neat!

hola como me podrias mandar el papel verde que aparese en el video y cuanto bale seria para toda la vateria saludos desde veracruz mexico

Bum Wrap Rocks!!! I wrapped my TAMA Swingstar in Green abalone from them

This guys a goof. good video

@vanzdrumming Did you use the same two clamps on the bass drum also? It seems like it may not hold the wrap as well.

How do you reinstall the air hole vent chrome back?

What about the hoops on the kick drum? Can they be wrapped to match the drum?

I have been wrapping drums for 25 years. I do not like cheap stickyback wraps. I do it like they did back in the 60's. I use contact cement. It's harder to do but it last for another 50 years. I have never had a drum come back to me.Some drum companies are easier than others to remove the wrap. Vintage Gretsch comes off easy because the shells are maple. Vintage Ludwig and Slingerland are much harder to remove because of the mahogany wood. You have to use a heat gun and be careful the old wrap will catch fire if it gets to hot.

I want to do this.Nervous about doing this.

when the shell was stripped down, is there a difference between the top and botrtom of it? Does is matter what side the batter head and reso head goes on? I think the floor toms will have mounts but what about the smaller toms?

I’m actually drinking a Heineken while watching this video

I couldn't sleep so I decided I would listen to some beats. You know, give me some ideas for jamming tomorrow. Now I'm wrapping drums with Randy, also browsing the Bum Wrap site, cause I have some extra drums that I have added to my kit that don't quite match and like most musicians us drummers especially it is unnoticeable to anyone else, but it erks me to death. So yeah, Thanks for the discount deal... I'm gonna match these babies right or maybe do them all something new...

Did you find any difference in resonance, tone, sustain etc. of the drums after wrapped?

Awesome wrap and wrap job. And that laugh...

Did you ever wrap the snare?

So let me get this right. You send your drum sizes and the digitized cover you want and they send you the correct size wraps. Do they all come with pre-glued seaming?

thank you for this video haha" id like to see this guy's son react to this lmao

Love your humor! You rock! See what I did there?

I’m sold

Haha, you're funny great video. I'm going to do this soon.

I've been watching for an hour and a half... is he almost ready to put this thing on?

At first, I thought that you worked for Gibraltar? You seem like a cool dude that would be fun to hang out with. Best wishes to you and your family and remember...If you're not happy, you're doing it all wrong. Peace.

Soooo what is the average rough cost to have this done to a standard 5 piece kit?

Where can i buy it in germany? or only in US?

Your vent hole unscrews. If you have riveted holes, it's a lot more difficult to work with wraps, precut or not.

where you located?

ordered a set from bum wrap. it was color selected from their very own library of colors. the color i recieved was far from the color depicted, yet when i attempted to contact them to rectify the issue, they ignored me at every chance. although your experience may vary from my own, i would not recomend this company to anyone. i'm out 250$ of my hard earned money and didn't even recieve so much as an apology.

lmao the first few words were hilarious

isnt there a cheaper way? i just bought a floor tom and this co wants about 50.00 for a wrap for it.

From the website it seems like Bum Wrap doesn't sell sparkle wrap? I'm truly bummed. :-(

cool wrap...cool company... loooonng a$$ video for what was done here. Jesus. (tip: videos can be edited prior to uploading).

It's all about bubbles, man

You need to invest in a pencil and an adjustable square… Make marks!!

Ah ! how many Ah in there.

This is the opposite color scheme of what I want lol

Hey you gained some, eerrr good life ? :p

Get a 5% Discount at Bum Wrap Drum Company just for mentioning Vanz Drumming! RVP bumwrapdrumco com

Dude youre not black 😂😂😂😂 JK