THIS IS THE VIDEO I HAVE BEEN WAITING FOR EVERYONE ALWAYS MAKES THESE INSTILLATION LOOK HARD ASF, you explained exactly where the individual pets are suppose to be at the end of instillation

Thanks bro this was really helpful I had ordered two sets of hids and was tripin out my relay harness should come in tomorrow hopefully it works

Thank you I'm glad I found your video I have installed hids on all my cars for years and just got a 2013 kia optima used and the only video showing HID install has a relay harness and I've been trying to figure out why you have to have that and I'm glad you explained it I did not know that I've always done Hids the regular way I also just got a 2014 Kia Forte and I took my HIds out of my 05 Malibu because it was the same bulb size and they have worked fine without a relay harness

Simple yet, thorough explanation. Thank you.

man your video helped me alot. I have been looking for this type of video for the longest. Thanks again for video

Bro your video is still super helpful even today thank you 💯

Thanks for the Video, this is just what I needed. I wish I would have found this the other day when the car was all apart- cant understand why DSPECK sent me the light housing without any instructions

hey man i have that issue with my car bt i want to knw after installing the relay will the auto switch for the headlights inside the car work?

Hi bro great video I want too know ware did u get Decoder Resistance Load Resistor Canbus yellow one

Can you connect the black wire straight to the negative part of battery?

The cable that was going into the ballast where does that go

Hi sir i intalled hids in my foglamp but my fuse blown. Any idea what to do?

Bro I had the same thing all I did was cut a hole in the middle and run my wires through the middle of that rubber cover so the cover still cover the hole in the wires ran through the middle of that rubber cover

I would like to know if you are happy with the kenzan hid and did it ever cause you any kind of problems with dizziness or dizziness when out of the Bells will now I just want to know everybody's advice if you like him you know from 1 to 10 how would you rate them I would like to know also I bought the kensun hid still it's the 6000k 11s for my 2011 Ford Fusion with the projectors that have them already built in Factory and I would just want to know if everybody's happy with it if it's a life span or more you know someone to know.

Thanks man.

Drill a hole in the middle of the dust cover the size of the grommet

mine came without resistor and says on balast starts without relay?

this shit confusing as fuck thanks for no help now I can't straight pipe my V19 Civic

Thank you.

🤣🤣🤣🤣🤣🤣"I just keep it like this" I'm surprised you didn't screw ballast to expansion tank xD

I watched your video because the black box making clicking sound sound and my light is not working. So you explained all stuff resistor,ballast, wires and when you come to black box you just skipped it so I guess you have no clue what it does and what’s the name for it. So you didn’t explained that good guess you know same as me.

but my relay socket dos not match my car socket :(

Omg cut the dust cover in the middle

What a birdsnest! LEDs are much easier.

loved your first vid

Not good to leave your rear cap off your lights

I bought a used Mustang and the headlights sucked. I had to tear a bunch of this garbage out. rewire my plugs and put stock lights back in.

Wait... So the load resistors are just chilling, not mounted to anything? And one of em is inside the 'cold air' intake? So, you installed an intake air heater element! Kinda like BMW does... The dust cover is there to prevent your headlights for getting all dusty and shit. It's gonna suck balls when you try and detail your car, and keep washing the headlight lense but it just won't get clean. Cause it will get dirty AF on the inside. Duct tape would be totally fine, barring the car is what you might consider a 'beater' But I think your car is nice and deserves better. Cut a hole, stick the harness through the hole, use a number of glues and tapes any of which would work. (use liquid electric tape) and secure the load resistors to something, just not the body or anything plastic.

I appreciate the effort to upload, but you talk too much and your camera shakes like crazy. Honestly I stopped your video at minute 5:00. You are showing exactly the opposite of how it should be done. 1. HID bulbs go into projector not reflector housing, you will glare at other drivers. 2.Those ballasts could have been installed in better positions and hidden below all those plastic stuff. 3. The wiring grommet has to be attached to the rubber cap doing a circular cut and passing the bulb and connectors through, that way it keeps out moisture and dust. 4. Tidy up your installation by using zip ties to order all that messy wiring. You don't want cables hanging there it is dangerous and look awful. The only thing done right is the use of relay harness, that way you'll preserve your car's lighting wire as the power go directly from battery and ground to the ballast. For anyone watching this video: don't install HID kits on reflector housings. Don't do what this guy is doing. Be clever.

what a horrible installation. 👎👎👎