3.04kg Lightweight 6000 series aluminium crash bars for the strength you do need without the weight that you don’t. Find out more and buy here: www.adventure-spec.com/defaul...
Пікірлер: 22
@lewis0588 Жыл бұрын
Incase anyone is installing theses and doesnt want to mess around... 12mm to remove the factory bolts. 1/2" to install the new ones, except the two under headlights are 10mm. Torx T30 allen key.
@michalcudek3 жыл бұрын
Nice music.
@carldanielsson44404 жыл бұрын
What is the purpose of the plastic bar clamps?
@bosley19804 жыл бұрын
yes I am also interested and it looks like it is screwed into plastic part :-(
@flyinbrianbmx4 жыл бұрын
@@bosley1980 It's not screwed into the plastic, it's clamped around the bar. it's sort of like a pad/buffer for when you do drop the bike so the metal of the bars don't bang up your plastics.
@RathinChiku3 жыл бұрын
helps to slide the bike without damaging the crash bars.
@grandefromage46072 жыл бұрын
I just fitted these. In the instructions it stresses to make sure the bolts are installed from the throttle/water pump side, but this shows the opposite? I wouldn't say these are the most sturdy thing ever but will give some protection for less weight than many other variants. Blue colour doesn't quite match 2022 blue, not as shiny, not perfect finish either. But I'll keep them. Look better than black.
@adventurespec2 жыл бұрын
Thanks for the feedback, if you'd like to make some suggestions we have this section on our site which you might find of interest: www.adventurespec.com/product-development
@grandefromage46072 жыл бұрын
@@adventurespec Thanks for the reply, but more helpful would be to say which way round the bolts should be? You Tube way or printed instruction way?
@markbay96683 жыл бұрын
I have heed full bars (bunker ) weight is 10.5 kg which made my bike super top heavy and the handling on dirt curves is not good. Am thinking really of selling mine and get theses ones they are 2.8kg which is amazing.
@Lethalish233 жыл бұрын
The mounting tab design on the bottom left side is terrible. It bent so easy with a 0 mph tip over. Look at the warranty on there website... Designed for cosmetic purposes only. Reached out via email with no response either. The right side is stronger because of the different mounting tab. Wish I had bought heed upper bars. It's not the aluminum strength you have to worry about. It's poor engineering at the mount. I'm happy with AS rear rack and pannier setup. Crash bars are trash
@rogerhetherington19033 жыл бұрын
I dropped my bike yesterday on the right side in deep sand no damage. but then dropped it on the left side ( still deep sand) the bars bent all the way in to touch the plastics and a small bolt came out of the lower cross bar. this was a low speed crash 5-10mph in sand dunes. Going to bend it back for the time being. Then to buy some Heed bars.
@atprodT7004 жыл бұрын
hi it's a joke an aluminum crasch bar if there is one thing that must be steel it is a crasch bar. aluminum does not have the same resistance. on a bike of 200 kg you will not feel 2 kg more at best you can gain 2.5 kg on the pot and 2 kg by installing a lithium battery.
@alrightdave61354 жыл бұрын
I was going to buy these bars. Your comment has stopped me.
@bosley19804 жыл бұрын
Michael B if ALU bars weight is 2kg, in mild steel bars (tube same thickness wall) 7,4kg will be...
@atprodT7004 жыл бұрын
@@bosley1980 Hello, I always lighten a maximum my motorcycles but for bikes dual sport of (200 kg) 440 pounds, having a high fairing. Aluminum is not the right choice, we are far from the resistance of steel. for equal resistance, a huge aluminum tube diameter should be chosen to reach the resistance of the steel. but if you are convinced that it is the right choice, then buy. (I work steel for many years and a little aluminum, copper, brass and other materials) cordially. .
@firstMexican4 жыл бұрын
@@atprodT700 I have been working with dural for 15 years and I don't think it would be a bad choice;)
@hankschwiebert14574 жыл бұрын
Aluminum, while softer, has a higher strength to weight ratio. Meaning that if you had two beams, that both weigh the exact same, with the only difference being that one is made of aluminum and therefore has a bigger cross section, it will take more load before it breaks (generally speaking). This is coming from a mechanical engineer. Personally, I still prefer steel for things like this because it doesn't succumb to fatigue as easily so you can bend it back after falling multiple times. Also, weldability is a huge plus.
@savardr64 жыл бұрын
again great product but annoying music
@ThrillaPark3 жыл бұрын
Watch on mute.
@grahamgillette53934 жыл бұрын
Watched 30 seconds of the video and deleted it,why, the music who in their right mind thought this would compliment their product
@flyinbrianbmx4 жыл бұрын
Deleted what? Hopefully it was the KZfaq app on their phone and we'll never hear back from them.