How to Measure (PoE) Power Over Ethernet

Рет қаралды 24,299

Күн бұрын

Are you looking for easy and inexpensive way to measure Power Over Ethernet? Chad Szekeres of Devine180 demonstrates the Hobbes Inline PoE tester that detects the PoE power from a Luxul PoE Network Switch (PSE) to FLIR and Inaxsys IP video surveillance cameras and other Powered Devices (PD). Learn to overcome the challenge of troubleshooting Power Over Ethernet and how to measure the actual wattage draw of surveillance cameras and other PoE powered network devices and determine the voltage drop that occurs in a network cable run as the cable distances are increased.
Items Shown In Demo:
Luxul - XMS-5248P - www.luxul.com/switches/poe-sw...
P3MPOE1-15 - Preferred Power Products - www.pthree.com/poe-switches/p...
FLIR Systems, Inc - Saro DH-390 Dome - www.flir.com/products/saros-d...
Inaxsys Security Systems Inc. - INSDO8360IRWA - www.inaxsys.com/en/products/c...
Raytec Ltd - VARIO 2 IP - www.rayteccctv.com/products-c...
Hobbes - 256318K - www.amazon.com/Hobbes-256318K...

Пікірлер: 14

@JIMMYPOP7505 2 жыл бұрын

Good video. Finally a pro that explains it. I’m a cctv pro since 1983. I finally get the poe switch operation. I was missing the pd simulator function and why my poe tester wasn’t showing me a voltage current value. Very good video. The boring stuff is the best part to understanding poe. Do not skip it! Many thanks. Jc cctv services. New York City

@ShooterQ Жыл бұрын

Thank you. Very educational.

@dennisblair3624 2 жыл бұрын

This tester is no longer available from Amazon. Anyone have any recommendations for a similar low price tester?

@DanBellJr 2 жыл бұрын

Chad, I think you have your max power delivered watts for PoE+ & PoE++ (type 3) swapped on your Power Sourcing Equipment slide starting at the 2 minute mark. Slide is incorrectly showing Type 2 at 60W and Type 3 at 30W.

@stevek6425 3 ай бұрын

Your Amp readings do not correspond to the display on the unit. you say ONE POINT EIGHT AMPS and the meter shows POINT ONE EIGHT AMPS then you do it again with ONE POINT FIVE AMPS and the meter shows POINT ONE FIVE AMPS. 9:50 time stamp. I don't understand, which is right?

@boedillard8807 3 жыл бұрын

I could be wrong but to test, you would need something that draws the maximum power and tells you what the wattage rating is. Otherwise you may have to measure twice with this thing.

@TheNinjaMarmot Жыл бұрын

2:30 PoE+ 30Watts UPoE 60watts

@fdimichele Жыл бұрын

I would just take a multimeter and try to clip it to an unbraided end of 8p8c connector. I assume you could get a resistance and then use voltage to calculate load...

@BharatPatel-qe8qx 6 ай бұрын

Hi, Testing device is too good, I would like to see the same testing for 60W and 100W. Could you help on the same.

@thomasjefferson3552 Жыл бұрын

If i am going to run poe cameras at my home do i need a poe tester?

@fdimichele Жыл бұрын

No. You can buy one independent POE power supply to test cameras then use POE switches. In addition, I recommend good quality connectors (without corrosion) that fit good quality cable (CAT6) and good software (not the stuff that comes with the cameras). Technically, the connectors should match the cable size. CAT6 wires are slightly larger. Thru-connectors are frowned upon but easier. Blue Iris works well for Windows and probably great ones for Linux too.