How to Press a Ball Joint

Рет қаралды 4,083,936

10 жыл бұрын

Ball joint press. Learn how to press a lower ball joint by using a ball joint press. I show you in depth how to press out a bad ball joint and press in a new ball joint. I go through what adapters to use, how to use them, how to properly press the ball joint in and out without damaging it, and give you tips and tricks along the way.
Ball Joint Press I used: www.amazon.com/gp/product/B002...
Quality/Inexpensive Ball Joints: amzn.to/1X4yBJh
How to change a ball joint (all of the steps): • How to Replace a Ball ...
Cutaway of a ball joint: • What's Inside a Car Ba...
How to tell if your ball joint is bad: • How to Check if a Ball...
Become a ChrisFix Subscriber→ kzfaq.info_c...
Instagram→ / chrisfixit
Facebook→ / chrisfix8
Website → www.ChrisFixed.com
My Channel Home Page → / chrisfix
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Thursday*
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.

Пікірлер: 1 800

@anitagofradump5195 Жыл бұрын

This walkthrough had no business being as clean and well edited as it is. Especially considering this is nearly 10 years old. Thank you Chris for the amazing video

@loyaldavis 5 жыл бұрын

This is absolutely one of the most clear and concise instruction videos, of any kind, that I have seen. Really great job Chris.

@NathanChase72 Жыл бұрын

Say it again Preacher!👏👏👏

@levicallis459 2 ай бұрын

I second that , very well done

@user-oq8gn4cl6e Ай бұрын

Amen! His videos are fantastic.

@CTBlankenship63 6 жыл бұрын

I'm a computer programmer ... a friend of my son's sold us a 2002 F-150 for $800. I now know why he sold it for $800. The entire front end required replacement (tie rods, upper control arm, Pitman arm, idler arm and lower ball joint). I took this to the local Ford stealership, the amount they quoted was more than the value of the truck itself. So, my sons (both mechanical engineers from UNCC) decided to do the work ourselves. After multiple You-Tube videos it became apparent that the stealership was exactly that. We rented the tool you suggested from Advance Auto (for free) and replaced the ball joint with the valuable instruction you provided here. Way to go Chris ... you ROCK.

@jodrhh 4 жыл бұрын

Chris, you are so freaking detailed oriented. Nobody comes even close to you when it comes to repair videos. My respect!

@dwightpayton3582 9 жыл бұрын

Hands down one of the best walk throughs I have ever watched.

@chrisfix 9 жыл бұрын

Dwight Payton Thank you! Glad you found the video helpful!

@yogishicksville2789 5 жыл бұрын

@@chrisfix Bryce playing very good video you should be on TV on commercials

@hedhigh520 3 жыл бұрын

Seriously!

@raulvega6562 2 жыл бұрын

I agree! Thanks for the walk through Chris.

@kyriejayson2413 2 жыл бұрын

I dont mean to be so offtopic but does someone know of a method to log back into an Instagram account? I stupidly lost the password. I would love any assistance you can give me

@toddeveretts5595 3 жыл бұрын

I've wrenched on cars for 35 years but never had to do a ball joint until this week. This was an outstanding video and well thought out. No needless chatter, every word had a purpose. Outstanding!!!

@willdavis6657 9 ай бұрын

This was a good video , and the chatter was down to a mininum and as needed i wish you woulda seen the video before I seen this one that guy spent like a half our telling us his entire life story I didnt even watch the rest of it I went straight for comments and told him he was fired way too much talking

@milesbizzell8811 9 ай бұрын

Wow as a shade tree mechanic and I have never done a ball joint. This video makes things simple. Appreciate the time he took in preparation of the camera and only saying exactly what needs to be said. Liked and saved

@idahogreen2885 9 ай бұрын

Word🤜🏻🤛🏻

@jonguy4337 2 жыл бұрын

From a Mechanic of over 45 years great video dude

@chrisfix 2 жыл бұрын

Thanks a lot!

@johnscott1872 Жыл бұрын

Thanks Chris, finally someone who actually showed how to use the tool and explained it perfectly. Now you Other utube teachers ...takes notes from Chris. Teaching is explaining in steps and small details. Thanks Chris, you're the man.

@robbert1210 5 жыл бұрын

As a professional (and ever learning) mechanic, your video's have been really useful, and this one came in pretty handy again. Thanks and keep being this awesome man!

@Vekurus 2 жыл бұрын

Honestly, one of the more comprehensive well explained how-to for the press kit. Really appreciated the clear instructions and explanation on all of the tools and why/how they will work.

@JustAnAverageBrad 6 жыл бұрын

glad to see you explained the grease port "this side inboard"...90% of youtube ball joint video makers have no idea how important that part is

@andrewkeough3565 2 жыл бұрын

Literally the only channel that wasn't effected by removing dislikes, BECAUSE CHRIS KNOWS HIS STUFF!

@SeeMooreVids Жыл бұрын

Excellent tutorial. I’ve had it with tool rentals as there always seem to be something missing or doesn’t quite fit. I’m 70 but capable of these jobs. I figure the savings in labor will more than pay for my new press, large spindle socket set and a decent torque wrench. Wish me luck. 👍

@dunebasher1971 5 жыл бұрын

Great video! Just as an additional heads-up, when installing the new joint, you didn't need to flip the press over. You could have left the screw facing upwards. It would obviously have been pressing down on the receiver cup for the top of the ball joint, but that's fine - the joint would still have been forced upwards as you tightened the press. Another handy tip is to put the ball joint in the freezer overnight and only take it out just before you're ready to install it. The metal will contract slightly with the cold, which will make it even easier to get it started in the hole by hand before you use the press. This can be very useful to avoid getting the joint cocked in the bore. The same trick works with bearings.

@seenoevilhearnoevil9067 4 жыл бұрын

Wow, That's a great idea. Didn't know that help me out. I got to do some of that stuff when the weather cools down a bit. Thanks.

@bradt9350 3 жыл бұрын

That might be true... I thought the same thing, but the cups and caps are designed to fit the respective end of the press and threaded bolt. Sometimes you just have to stack them only how they fit together and still house the ball joint inside properly. I've done this more than a few times. Some times you have to use heat or even drop the control arm and use a standing press to get the ball joint out because this kit just isn't enough.. Chris: Always spot on and to the point in all your vids. Good work, always... Brad

@amartinez2071 2 жыл бұрын

Saved this video for my job on the trailblazer this weekend.Awesome camera work and perfect angle.Yes you can keep the bolt at the top.

@WolfSpiritJag 5 жыл бұрын

Chris. I cannot describe my gratitude for your DETAILED SIMPLE CLEAR INSTRUCTIONS WITH GREAT VIDEO SHOWING CLEARLY EVERYTHING YOUR DOING. When i watch yout videos i feel confident and knowledgeable about what im doing with very little to no doubt or concern or feeling lost about half a what im about to do. And you follow safety procedures and show how to do things the RIGHT way. Instead of just here smack it on there itll be alright leave it dirty its okay if its half ass n crooked. Thank you. Again. We KZfaqr's and DIY's are super blessed and lucky to see your videos. You have helped me so much. Thank you.

@scottjames8498 Жыл бұрын

Been watching your channel for years Really like that you work on the driveway and not a 100k shop!

@jb_bmwrepairlyfe4704 4 жыл бұрын

I’m very impressed on how you can get to those camera angles while working on the car! Good job!

@f3rg971 5 жыл бұрын

This is probably the best made auto-related how-to video I've ever seen. Thank you so much!

@chrisfix 5 жыл бұрын

Thanks

@rjjr7064 3 жыл бұрын

So many people waaaay overcomplicate this. They say you need "special tools" and you should only do it if you're experienced. They rush through their tutorials and I learn nothing. ChrisFix you are one in a million! Your tutorials make so much sense a 5 year old could follow them! Thankyou for all you do.

@troys5286 3 жыл бұрын

To be fair you do need special tools.

@stephaniefuentes9881 5 жыл бұрын

I would never be able to make the trickier repairs to my vehicle without your videos! Thank you. Thank you. Thank you.

@colorocko1 5 жыл бұрын

Thank you. I appreciate the detail in your explanation!

@lyleyla9275 4 жыл бұрын

Chris, you do a fantastic job explaining things clearly. I have a 99 Chevy Tahoe that needs all kinds of front end work. For a chick i can do almost any engine work myself (sometimes i may need a lil muscle), but i am completely clueless when it comes to suspension/front end work so i really dig your videos man. Incredibly helpful!

@countrysmurfcomedy3099 Жыл бұрын

💪🏾💪🏾💪🏾💪🏾💪🏾💪🏾🔧💙

@piranhaphish Жыл бұрын

I don't know how many videos I've "liked" on KZfaq, but I'm sure I can count it on one hand. I'm pretty sure I've never commented on a video at all. This video is one of the most deserving because so many other repair KZfaqrs can learn from this. The content, guidance, editing, audio ... all of it ... are direct and useful. When searching for general advice in the future, this channel's name is going to be part of the search terms going forward.

@mannyperez1394 2 жыл бұрын

This man is a natural born educator. Thank you so much

@brandonf.2528 5 жыл бұрын

Damn dude - this is probably one of the best 'how to' auto videos I've seen. Clear and detailed. Very well edited. Great camera angles. This is why I love KZfaq! Awesome work and thank you!

@BigOldCarChannel 9 жыл бұрын

Guy, that's one exceptionally clear and instructive video! Excellent work, you should be proud of yourself for this one. I'd thumbs-up twice if I could.

@chrisfix 9 жыл бұрын

BigOldCarChannel Thanks a lot!

@mayrarodriguez5539 5 жыл бұрын

ChrisFix,I don't know what to say to you.

@ironfistarrival 5 жыл бұрын

@@mayrarodriguez5539 :Blow a Kiss , Blow A Kiss ....

@RudeDog303 5 жыл бұрын

@@chrisfix I agree, great instruction, video, footage, everything!

@funtimeproduction8151 4 жыл бұрын

Here here

@jacktobin8183 3 жыл бұрын

Just replaced , my rotors , calipers, pads , coil springs , Shocks all around , adjusted torsion bars , both stabilizer bar linkages , THANKS CHRIS . You are the man , your videos are big time helpful . Keep up the great work

@russellvandiver1625 5 жыл бұрын

This was by far one of the best videos I have seen explaining how everything works in removal/install of ball joints! Thank you and great job! Russell

@bushmaster2936 8 жыл бұрын

Perfect video quality and instructions : ) Keep up the great work !

@cri8tor 5 жыл бұрын

It's been years since this was posted, but still a great tutorial.

@fireye2012 4 жыл бұрын

Your good Chris. This is one of the best instructive videos I've ever watched. No off topic banter and excellent camera work.....and I love the pace at which you went. Nothing like having to sit and watch someone spend 5 minutes turning a wrench or socket.....I like how you showed us the start of turning the wrench and the finish of turning a wrench and leaving out the middle part of just watching wrench turning....lol.......GOOD JOB!

@Joemama-km9np 3 жыл бұрын

I've been looking at KZfaq how-to videos for years and this is up there in my top 10 for concise and easy to understand, good job my man. Now I wish I had KZfaq when I was rebuilding a 67' Mustang in the early 90's.

@BBB-ly8ro 4 жыл бұрын

The best instructional KZfaq video I’ve ever watched. You made it look like you do it for a living. Im willing to bet Beto o’Rourke can even do it after your tutorial.

@FlyHeadCement 9 жыл бұрын

Dude, one of the best how to vids I've seen. Clear, concise, and excellent camera work. So many shade tree mechanics out there explaining things poorly with crap camera work. Well done Chris and thanks!

@chrisfix 9 жыл бұрын

FlyHeadCement Thanks man! I appreciate it! I am glad the video was helpful!

@Derek-ld4kn 4 жыл бұрын

This is outstanding! As a family, "backyard" mechanic for many years, I commend you Sir!

@stefangoins2164 3 жыл бұрын

thank you chris for this amazing video, even going to college and learning the material doesnt teach you everything im a visual learning so watching your videos keeps my brain sharp and my learning endless.

@aircomp 4 жыл бұрын

You're the man, Chris. Just saved about 750 bucks doing this!

@jasonpiazza4037 8 жыл бұрын

Very intelligent and clear explanation. Well done!

@rasputinsorphan1260 3 жыл бұрын

Thank you for your straight forward, easy to follow tutorial on a ball joint press. This and your other videos are why I still have the vehicle I do. Thank you!

@tonyvienonen6589 4 жыл бұрын

Straight and to the point, the way the walk through video should be. No useless side conversations.

@topgrain 8 жыл бұрын

A lot of times it's hard to see what's happening in the procedure, but your video is great and also excellent work. Thanks.

@IlluminatingNight 6 жыл бұрын

I'm honestly amazed every time I watch one of your videos. I've never seen anybody make something so easy to understand and so clear and concise. You're always a big help.

@chrisfix 6 жыл бұрын

+Brandon s thank you

@martywright1829 Жыл бұрын

@@chrisfix that’s a good kit wish we could rent something like that in Australia

@garymahon1955 Жыл бұрын

Thank you a ton Chris! Very helpful to this 68yo man who cant afford to have shop do it again. They did the other side, but im going to do what you did and rent the tool. You kept it nice and simple. Bravo. Great job !

@jackm7976 4 жыл бұрын

Many said it before me . One of the best videos I've watched, very detailed. Wish all videos were this informative.

@flyboy2610 3 жыл бұрын

Great video, Chris! One thing I would like to add: when using a screw press like this, always grease the screw threads before use. Makes things easier and extends the life of the threads.

@benjaminabel8596 Жыл бұрын

I was wondering that. He did do it in a later video.

@keithheimericks4562 9 жыл бұрын

Outstanding tutorial sir!

@leeshaw5136 5 жыл бұрын

As always, excellent work. Clear, concise, stress revealing, and informative.

@lyndalarvie9926 3 жыл бұрын

Thank you. My Dodge Dakota was getting a maintenance work up with 54,000 miles on it. I shared with my mechanic and took him for a test drive to alert him to the noise in the front end. When I picked up my truck he said my lower ball joints were bad and suggested I get it taken care of. I am a 67 year old woman and wanted to have an idea of what a ball joint was and how to replace them. I Got it! The video was well done. I have an idea of how the mechanics will replace them. Thank you.Lynda

@daddy9minnich777 7 жыл бұрын

Awesome video...you have great articulation and presentation skills, dude...some of the best videography I have seen. God Bless and Thank You!!!

@natgilson 3 жыл бұрын

Dude, thank you so much. That was so perfectly clear.

@cookingwithbuds3963 4 жыл бұрын

Dude I'm a first-time guy that's trying to mess with suspension issues and I looked up this video because I need to replace my ball joint and you give me the confidence I need to be able to do it myself thank you

@ronib2508 5 жыл бұрын

Great job CHRIS. First time watched one of your videos. Great explanation, no rubish talking, no time vasting jockes. Very professional and helpfull explanations and advises. Great camera work. Well done my friend.

@mv3098 10 жыл бұрын

Really great videos Chris. Your running commentary is really good! Thanks for posting.

@chrisfix 10 жыл бұрын

Thanks for the feedback! Remember to "thumbs up" the video (it helps me out, thanks!).

@smb1014 9 жыл бұрын

Excellent job! I learned a lot from this video.

@John.Skelton 2 жыл бұрын

It always looks SO EASY when you do things! I always run into snags or problems! 😅 but you have seriously saved me so much money by your videos and me doing things myself so thank you! 🙏

@franksloane9579 4 жыл бұрын

i'm with the other guys here; I've watched a lot of these videos and this was by far the most precise. great job guy

@latinknight29 9 жыл бұрын

This is the best diy ball joint video i have seen. Great video very detailed and informative.

@chrisfix 9 жыл бұрын

latinknight29 Thanks! I am glad the video was helpful!

@mariarodriguez-ud9hq 5 жыл бұрын

Thank you Chris! You are AWESOME as a Teacher! VERY ARTICULATE AND CLEAR! KEEP IT UP!

@jtdouglas9535 4 жыл бұрын

For anyone giving this a thumbs down, you're just not happy in life. This is an awesome tutorial. NOTE: there is no need to flip clamp. It pressures equally on both sides for install and removal.

@chrisfix 4 жыл бұрын

thanks for sharing

@SimpleLife1971 6 жыл бұрын

Chris, Your videos are about the best I've seen so that you very much for taking the time to record, in GREAT detail, all the step by step procedures. The ball joint press will work the way you've shown to press the new joint in but you and also use the press without inverting it with the right adapter configuration, I do it all the time.. With the right tools and a bit of instruction we can do anything! Thanks!!

@4leafmetal 3 жыл бұрын

Thanks Chris! I'm going to attempt to press out and replace the ball joints on my 2008 Chrysler 300 5.7L. Wish me luck brother!

@chrisfix 3 жыл бұрын

Awesome! Let me know how it goes!

@CarsonRH 3 жыл бұрын

@@chrisfix the ball joints got him he’s never coming back

@fredgervinm.p.3315 3 жыл бұрын

@@CarsonRH I lost a friend like that...

@roccomauro6165 4 жыл бұрын

Not even my vehicle but you explained it perfectly great job once again

@dougmccoll6126 4 жыл бұрын

Not sure what is wrong with all the thumbs-downers, because this was one of the most concise, visually simple and clear, accurate descriptive, and good sounding, KZfaq instructions I've seen.

@michaeldman9068 3 жыл бұрын

Wow, the best how to video I've ever seen, You really did a fantastic job clearly showing the proceeder, and exsplaning the correct way to use the press, Most excellent.

@skippy594 5 жыл бұрын

Hey Chris, Just as with just about all the other comments Ive seen.... Dude, super informative and helpful video. Thanks for that. Thumbs up and subscribed, sir. 🙂

@hunterknappre1271 2 жыл бұрын

logottaI o ol we uiuii think o g a hasonna good night I hope youdarling well ’re the u

@cnguyen616 8 жыл бұрын

Excellent presentation. Thank you brother.

@chrisfix 8 жыл бұрын

cnguyen616 Thanks a lot! Glad the video was helpful!

@THOMMGB 2 жыл бұрын

Hi Chris, This is an older video but the information is timeless and perfect for what I need to do.

@mmedrek 4 жыл бұрын

Excellent! Thank you for pointing-out the little details like which direction to have the grease nipple pointed, and why.

@WTFarmGirl 4 жыл бұрын

Ok, why all the thumbs down? It seemed a very straight forward video. KZfaq sent me here and I had forgotten I needed to know this for doing wheel bearings and the ball joint. So glad I watched this video, seems a very straightforward process. I'm assuming you have a video on replacing bearings too, so I'll go take a look!

@collinmullins1183 4 жыл бұрын

@The Profit no it's because they don't rent a free ball joint press anywhere

@georgeowen2083 4 жыл бұрын

Some people just need to be pricks.

@lovinlife6850 5 жыл бұрын

Awesome! Thank you Sir!!

@FullMe7alJacke7 3 жыл бұрын

Exactly what I was looking for, straight to the point with in depth explanations. Good video!

@SuperMetalFiend 6 жыл бұрын

I have an 08 Nissan Titan. I have nearly zero clearance above the upper ball joint. I was just about to remove the control arm to press the new ball joint in, when I found a way to press it in with the screw facing the other direction. There is SO many ways to use the accessories that comes with the kit, to accomplish the job. Love your videos, Chris!

@pusherpilot 8 жыл бұрын

Thanks Chris. Subscribed. I am rebuilding a 91 YJ jeep. Needed your help with the balljoints. Very concise and to the point with no BS. I appreciate you.

@chrisfix 8 жыл бұрын

Paul Roberts Awesome! I am glad you subbed and the video was helpful! I love Jeep YJs!

@dougchandler-christsbrothe5994 5 жыл бұрын

Very clear and concise! If I was interested in becoming a professional mechanic, I would choose your videos over a college class, any day! Thank you for being such a great educator!!! (-:

@agosto1685 Жыл бұрын

Very clear, correctly paced and good use of close-ups. Nice editing. Well done.

@claylindquist7503 4 жыл бұрын

You do a fantastic time with your tutorials. One of the best I’ve ever seen.

@didar389 8 жыл бұрын

Another great video thanks Chris

@chrisfix 8 жыл бұрын

danny love Thanks man!

@shadow6996 4 жыл бұрын

Don't understand why so many thumbs down, Awesome step by step instruction video.

@Echo024 3 жыл бұрын

Thumbs down are from people who overpaid a shop to do it and then realized they could have easily done it at home for a fraction of the cost.

@Sirgoofyboots 4 жыл бұрын

That’s a really great, well presented video. Tackling this one an 07 Sierra tomorrow and that was the only part I was iffy on. After watching this I’m super confident about tackling it now. Thanks man!!

@justgentile 5 жыл бұрын

This is fantastic. Perfectly well done. You articulated exactly what to do, which just made my life 100 times easier. And saved me $$

@memphisbankhead 4 жыл бұрын

Great video ... I bought this kit and was scratching my head like wtf is all these pieces .. I see now .. Thanks!!!

@idrissadamiba1364 4 жыл бұрын

OK. Would you mind helping me toi get it? I'm Burkina. Thanks.

@alexanderstephenson7039 9 жыл бұрын

Excellent video presentation.

@brianday6433 3 жыл бұрын

Very precise video. Well thought out with no wasted time. I do most of my own car repair work, but never attempted ball joints before. I may give it a try now.

@o.h.w.6638 4 жыл бұрын

You've helped me with my car so many times, now you're helping with my sailboat! My keel bolts refuse to come out so I'll use this technique to squeeze 'em. Awesome!

@BigSarnt 9 жыл бұрын

Oh and one more thing Chris, bought that jack on sale as well lol Good ol Harbor Freight

@chrisfix 9 жыл бұрын

***** The nut and cotter pin should be above the control arm as you explained. It is really tight in there (probably why the tech rounded the nut) but that is the correct orientation. Glad you are doing the job this time so you know it is getting done properly! Let me know how it goes!

@jeffstone2601 9 жыл бұрын

chris la calidad de la marca powerbuilt de 1 a 5 cuanto le pones? Quality PowerBuilt of 1-5 put much did you put ? what is your rate of 1-5 gracias thank you excusa la escritura use traductor

@chrisfix 9 жыл бұрын

paddy perez Busque en la descripción para el enlace a la powerbuilt usé . Es una gran calidad.

@jeffstone2601 9 жыл бұрын

ChrisFix gracias chrisF

@josuer.2723 8 жыл бұрын

+ChrisFix bilingual 👍🏻

@MarkXVance 6 жыл бұрын

Dodge knuckle joint removal

@tomlarocque4720 3 жыл бұрын

Chris fix has saved me thousands of $$ over the years. Me and my 2009 FJ cruiser are indebted to you ;)

@sammoreno8405 4 жыл бұрын

dude thanks so much for just having legit walkthroughs on these kinds of tools.... i was so confused when i opened the box

@chrisfix 4 жыл бұрын

I'm glad you found the video helpful!

@chrisfix 10 жыл бұрын

***** The split-ring flew to my right... Right after I said these things tend to fling haha.

@joshslowmez6065 9 жыл бұрын

YEAH I LIKE HOW IT DIDNT EVEN PHASE YOU COOL HEAD!!!

@charlesbalogh9286 8 жыл бұрын

+ChrisFix that's why they're called "Jesus" clips...as in JESUS where did that go ????

@rosierodriguez1390 7 жыл бұрын

+Josh Slowmez I am...

@earlmatheny4611 6 жыл бұрын

ChrisFix need traosson

@chibanenasro4383 6 жыл бұрын

Metrixe

@9014jayvictor 5 жыл бұрын

doing this tommorow have kit will travel

@9014jayvictor 5 жыл бұрын

I have been using this kit for weeks now and it works very well .. Nice video !

@frankmaceri5705 5 жыл бұрын

Thank you, I am about to change both upper control arms and my passenger lower ball joint. Your videos give me more confidence.

@mikelarochelle9890 5 жыл бұрын

Good job bud.... watched alot of videos before yours and it's the best..... I've changed alot of ball joints over the years but never had a kit.... was almost more confused when I opened it up but you made it very clear 👌

@davidsantoro9489 9 жыл бұрын

great video you should be a teacher great job thanks

@chrisfix 9 жыл бұрын

David Santoro Thanks a lot David!

@peted2331 5 жыл бұрын

Jesus... Could you be any more clear and detailed.. Awesome.

@ericmagallan 3 жыл бұрын

This is by far one of the best how to videos I've seen on any how-to's. Great work! I learned more than I needed to today about this process. :D

@muzzaball 4 жыл бұрын

Really good video Chris, as usual. Clear, easy to follow steps with excellent info on why we are doing it, thank you.

@KlrWolf 4 жыл бұрын

Just use a BFH and beat out the old joint faster

@tomasgarcia8159 5 жыл бұрын

You don't have to turn the C clamp up side down

@BPoweredLove 4 жыл бұрын

True. You can squeeze from either orientation of the clamp. But in a way, for those that were struggling with understanding how all the physics works, it helps to think of the driving direction correctly by flipping the clamp the opposite way when installing the replacement joint.

@jtdouglas9535 4 жыл бұрын

Was just going to say. Awesome video but clamp pressure comes from both sides equally. That's physics :) great video though