How to Replace Control Arm Bushings (EASY)

Рет қаралды 8,196,942

9 жыл бұрын

Control Arm Bushing Replacement. This video will show you how to easily replace Upper Control Arm bushings (press the old ones out and press the new ones in with common tools). This job is fast and easy and can be done with basic hand tools and a ball joint or bushing press which you can rent for free at your local parts store.
You can also use this method to replace bushings in your leaf springs and pretty much anything that has pressed in bushings!
Get inexpensive bushings here: www.amazon.com/s/?_encoding=UT...
Here is the press kit I was using (and I like a lot): www.amazon.com/gp/product/B002...
How to Press a Ball Joint: • How to Press a Ball Joint
How to Replace a Chevy Upper Control Arm: • How to Replace Control...
How to Replace a Ford Upper Control Arm: • How to Replace a Contr...
How to Replace a Lower Control Arm: • Replacing Lower Contro...
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Thursday*
-Website: www.ChrisFixed.com
-Facebook: / chrisfix8
-Twitter: / chrisfixed
-Instagram: / chrisfixit
-Subscribe Here: kzfaq.info_c...
-KZfaq Channel: / chrisfix
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.

Пікірлер: 1 800

@ericshaw7859 3 жыл бұрын

Tip: If you throw the bushing, ball joint or bearing in a freezer, it slides in even easier due to temperature contraction.

@chrisfix 3 жыл бұрын

Thanks for the tip!

@klausvonschmit4722 2 жыл бұрын

Great tip! Even now with having owned a hydraulic press for several years now to this day I still freeze everything prior to marrying whatever it is even though I have the capability pressing the square peg into the round hole due to my press is really overkill for someone who likes to tinker on things and to build loud obnoxious things with the sole purpose to drive them like an idiot..

@jeffgood6441 2 жыл бұрын

Pro tip you do that and you take a torch to the arm where it goes you should be able to tap it in with a hammer and right sized socket gota work quick or it will bind up part way

@williamdon3442 2 жыл бұрын

I do that to put a magnum.

@wmkess 2 жыл бұрын

I installed an upper main bearing on a 2 stroke outboard without a press by putting the crankshaft in the freezer and the bearing in the oven. Pretty cool although not sure it’s the best route for right tolerance cases like that lol. Seemed to work fine though.

@restfulplace3273 29 күн бұрын

9 years old video. Feels retro compared to the more recent ones. Thx for sticking with it all these years

@videodistro Жыл бұрын

It's a HUGE help to lubricate the threads on the screw. It's the friction of the threads that cause most of the resistance, not the metal on metal of the bushing. It also helps make your threads last longer from unnecessary wear.

@omartlili5849 9 ай бұрын

is it better using grease or something more oily?

@jimbeanmcqueen64 9 ай бұрын

@@omartlili5849 Oil. Grease is great at providing some longevity to what you’re lubricating. So unless you remove bushings on a regular basis then using grease would be unnecessary when you can just use to oil.

@TheCatOfAges 4 ай бұрын

@@omartlili5849 neversieze

@hextremelydesirable1648 2 ай бұрын

@@omartlili5849 thats what she said PULSECHAIN $0.00014

@SiboBushings 4 ай бұрын

Clear and complete explanation, one of the best videos on this topic on the internet.

@BigShmaxx 3 жыл бұрын

I’ve watched almost all of your videos, and honestly man I got respect for you. You never cut corners on explanations or safety . You do all your repairs with regular tools no matter the job and if it weren’t for you I probably would of gave up on a few things. Sometimes I wish I could just bring my dam car to you man you make it look so easy !

@mike8549 Жыл бұрын

I had to go to 4 different shops and spend thousands of dollars just to fail inspection and be told another 3k but i found all the bushings and itll cost 145 bucks, they said they cant replace bushings need the whole control arms and knuckles because thats what ford has written in their service manuals!! So looks like im doing it myself!!! Thanks chris! Once again saving the day!!

@Lstevens128 8 жыл бұрын

Chris, appreciate your videos - the BEST I've EVER seen. Crystal clear and to the point explanation leaving no room for error - very professional. Just can't locate a BJ/CTA Bushing tool kit as complete as the one you're using. All those extra pieces included in your kit has everything needed for any removal/installation. Keep up the good work!

@chrisfix 8 жыл бұрын

+Steven Leong Thanks a lot! I link all the tools and products I use in each video in the description so it is easy for you to find!

@MrCraiglicious 5 ай бұрын

Yes,excellent video and teaching skills. Strait to the point and no fluffing about. Best video I have ever seen to!🏅

@kr1886 6 жыл бұрын

Having watched several of your videos I'd just like to say they inspire confidence from being so well thought out and clearly presented. Great work!

@sethfoulk6990 Жыл бұрын

You should try being a teacher!

@logicalcontroversy672 7 жыл бұрын

"This would be a really good time to have a workbench. I'm gonna use the floor." haha classic.

@shermanbird3891 4 жыл бұрын

"Don't try this at home!"

@tjmarx 2 жыл бұрын

I really don't get why millennials don't understand the difference between a floor and the ground.

@riancallahan9685 2 жыл бұрын

Gitter done.

@timmickers 2 жыл бұрын

That was a legit shade tree mechanic move....we all do it😂

@superb63amg94 5 ай бұрын

Chris Fix is a national treasure!

@depth_and_breadth5255 Жыл бұрын

You're an excellent teacher and communicator. I'm always delighted when I see a video from you on some topic I search for, because I know you will address the important points, and will address any common difficulties. You've helped me save a lot of $$$ fixing things myself. Thank you! I'm about to replace the bushings on my lower control arm. The arms are in great shape, but the bushings have visible splitting all around. I live in the desert, so metal doesn't rust much, but the climate and the intense UV light makes rubber break down fast. This is, as always, a very clear video! You've removed any fear I had of doing this myself.

@paulroberts6163 5 жыл бұрын

These videos are great. Never tried to do suspension/ steering components. Chris makes it easy so it is almost like I want to. The video focus on the item rather then the person doing the work is brilliant.

@AustinCarter26 9 жыл бұрын

As a newbie to pretty much all car mechanics, your videos have been really helpful and clear. I'd love a really quick explanation on what the parts do or how the function in the vehicle itself. Thanks so much

@chrisfix 9 жыл бұрын

Austin Carter No problem Austin! I try to make all of my videos simple and easy to follow!

@deedgrabber Жыл бұрын

I've been watching repair videos on many different topics and yours are - hands down - the best. You have a definite talent for this.

@davidelias13 7 жыл бұрын

This is an excellent video. Your explanation is complete and your choice of words is spot on. Moreover, you go above and beyond to explain AND show with your camera exactly what is going on. Very few people take the time to put together such an excellent explanation, thank you.

@user-oc8dn3bc1p 4 ай бұрын

Very informative

@AlwaysOn702 8 жыл бұрын

I've watched a bunch of how-to videos and I like your explanations and visuals the best.

@guyantonelli5411 Жыл бұрын

I have been working on cars and trucks for longer than i want to remember, your video's are thorough enough for a novice to do the job right, very helpful and enjoyable to watch, thank you

@jimhaas3 7 жыл бұрын

Man, that was excellent! IMO your videos are by far the best of all auto DIY series. Keep em coming!

@WoodchuckNorris.8o 5 жыл бұрын

This is the best diy auto repair channel on youtube. It's allowed me to do my own work and save tons of money, and learn this stuff on the fly. I could not afford to have a car if you did not have this channel up. I really appreciate the work that you are doing!

@rickmckinnon5646 7 жыл бұрын

I want to say thanks for the "how to" videos,I've seen several and take pride in the fact I did it and didn't pay anyone for labor. I'm retired and disabled,so your videos do make a difference! Next task is that pesky shift lever indicator. Happy Trails!

@alia176 7 жыл бұрын

Great job Chris, you have the gift of explaining things real well and in a language that anyone can understand. What I really love about your videos is that you sound confident, you're precise in your language and none of those "umm" in your narratives. Keep up the good work man.

@elle26426 4 жыл бұрын

alia176 I agree with you. Chris you do have a natural ability to communicate what you're doing in straightforward language. As a female, I so often feel taken advantage of with car repairs. The suspension arms on my nissan bluebird have been done on separate occasions (different auto repairers) & I'm sure I was ripped off with the first job. If I had viewed your video back then I would have felt far more confident to discuss and query the work that was done. Thanks for sharing your knowledge and expertise (all the way to NZ!).

@zackvessels824 4 жыл бұрын

alia176 truuuuu

@georgecollier6352 5 жыл бұрын

Your videos are an excellent resource for me for my 1973 Challenger restoration project. Very thorough and informative. I appreciate your help!

@chrisfix 5 жыл бұрын

Awesome! I’m glad the videos are helpful!

@hwayneorr7532 2 жыл бұрын

complete and concise with enough explanation for first time users. Great video with excellent camera work.

@roberttretola8263 5 жыл бұрын

This is an amazing video. I love the way that you explain everything in full detail. You go the extra step to explain even the most simple things. Great video, keep up to amazing work. You sound like a prime time host.

@chrisfix 5 жыл бұрын

Thanks!

@rjallenbach1 5 жыл бұрын

I bought some used upper arms for my truck that provided additional suspension travel. Like you suggested I pressed the old bushings, painted the arms the same shade as the original manufacturer, then pressed in my brand new polyurethane bushings. It was easy and very rewarding

@tonyg.559 Жыл бұрын

😊😊😊😊😊

@cmcarlton212 6 жыл бұрын

You are an Amazing Teacher ! Thank you for being so detailed in your videos.

@singhsandhu6365 3 жыл бұрын

Thx to chrisfix today I replaced the bushings on the front control arm of my dad's fiesta although I'm 15 did all the work myself and the best part is the bushing was bad and the mechanics had ripped my dad 2 times saying the sway bar bushings are bad so everything to lower the subframe and make extra money...but this time I changed it and now the car is good

@KingZoneOne 2 жыл бұрын

You make some REALLY GREAT videos! Very professional, straightforward, and right to the point with excellent descriptions and explanations without any extraneous jibber-jabber. Great job , THANKS 👍🏽!

@808chevykev 7 жыл бұрын

Once again you're helping save me a bunch of money and add another notch on my diy wall of fame. You're an excellent teacher,thank you! Overhaulin' a '78 El Camino project and some here n there work on my '81 Camaro!

@chrisfix 7 жыл бұрын

+Mr. Dreadz awesome! I'm glad the videos are helpful!

@fvrrljr 6 жыл бұрын

Nice looking Tool! I used a vice on my '65 Mustang upper and lower control arms. this was back in '83 my hat off to the engineer who thought of this tool. Love your videos.

@ezralord4901 5 жыл бұрын

Chris, you make very good how to videos. Thanks for everything you do and keep 'em coming!

@pinachosaul7737 5 жыл бұрын

good job I have learned a lot from your videos thank you so much you really have the gift of explaining think keep doing a good job amigo

@TheJustina102085 4 жыл бұрын

“Easy” is debatable.. I feel good after doing my own fluid changes and replacing a new battery.. haha thanks for the video, this video was done so well it made me tackle this myself and probably saved some good coin!!

@sam33more94 2 жыл бұрын

Man!... you're the king of all mechanics!! I love to watch all your videos and at the end in every visual is the same good satisfaction that I can do it too! Thanks to you Chris!

@bitchplease1114 8 жыл бұрын

Best auto mechanic channel you can imagine. Chris, thank you, thank you very much.

@RiverWyvrn 9 жыл бұрын

It's so refreshing seeing a DIY channel actually recommending proper grinder safety :P

@chrisfix 9 жыл бұрын

***** Thanks! I try to recommend proper safety techniques whenever possible.

@jeffrichards9329 4 жыл бұрын

This is genius! I used this same setup (balljoint press and various impact sockets) to replace the bushings in my rear upper control arms. Would’ve cost over $300 to replace them! Regular bushing press wouldn’t have worked, because bolts were solidly seized (welded) to the inside bushing sleeves - so couldn’t pass anything through the old bushings. It took two afternoons and ten Sawzall blades to cut the old bolts loose and free the control arms from my car, btw.

@Ranger42 5 жыл бұрын

You are such a good instructor and your videos are so thorough and just plain fantastic

@valiaustin16 8 жыл бұрын

Dude +ChrisFix Your explanations are really clear and helpful, and you get right to the point. Never found mechanics this straightforward. Thanks!

@pops1981 4 жыл бұрын

You really produce great video's Chris. Reminds me of Ed China in the old days. I really like how you explain what you're going to be doing and why....before you do it. I appreciate all the effort you put in to your work, it is much appreciated.

@joeaviles2419 5 жыл бұрын

For everybody doing this, you need to have a spacer for removing the bushings on lower control arms (on older vehicles) and for most modern control arms. The easiest (and cheapest) way is to take exhaust pipe and cut it wide enough to fit in between the metal, but it must be cut in half (making two c shapes) in order to fit around the bushing to keep from bending the metal. Hope this helps somebody before it’s too late.

@paulmc9314 3 жыл бұрын

cutting exhaust pipe. thats a good idea, will remember this one

@jonnyz69 2 жыл бұрын

Now I have to replace my exhaust pipe. Should have thought this through a bit more...

@Sweenis80 Жыл бұрын

Necroing this comment but you can literally see the welds break when he pushes it out

@joeaviles2419 Жыл бұрын

Although this video is helpful, it is very important to not miss this step. Good job brother.

@abcdefghijk35945 7 жыл бұрын

I'm so glad you can rent the kit because on Amazon there like 350$! And the mechanic was charging 300$ for new bushings and and new tie rods to be replaced! Glad I found this guy!!!

@emilaznar526 8 жыл бұрын

Excellent video. You added a lot of extra detail which makes it easy to follow and clears up any misunderstanding.

@tylerfleming8460 7 жыл бұрын

Getting ready to change ball joints on 98 Chevy truck, your video was very informative on how to use press good detail Thank you!

@chrisfix 7 жыл бұрын

+Tyler Fleming glad the videos are helpful

@keithnoneya 8 жыл бұрын

Nice Job Chris. I've watched a few of your videos and I like the way you explain things and have your videos organized with tools and yo0ru tid bit advice like rent the tools from your local auto parts store etc. Only suggestion I have is to list all the tools in the SHOW MORE box. Best Wishes n Blessings Keith

@chrisfix 8 жыл бұрын

+Keith Noneya Thanks man! I link the tools I use in the description

@AdrianGeorge 11 ай бұрын

I'm just commenting to say, I've watched a load of your videos now, and your channel is by far, the best I've subscribed to. Thanks for teaching me a little something, and for all the effort.

@Xyreck 7 жыл бұрын

I love your videos. They are very easy to follow. And you explain things in intricate details.

@michaelovitch 8 жыл бұрын

It's stamped metal,you need to use a spacer between the two layers of the control arm otherwise you deform it or crack it,like here 5:20

@chrisfix 8 жыл бұрын

+michaelovitch Thanks for the tip!

@Mr.Beastforpresident 5 жыл бұрын

How do you know if the bushings are bad to begin with? Also have you ever seen or is it possible for the control arm bolts with Alignment keys to wear on one side of the bolt? In-other-words the shaft of the ( bolt ) that goes into the bushing spacer becomes oval from the bushing spacer constantly rubbing on it? I've seen that done to a bolt before on Dual axle utility trailers where the axles two leaf springs meet in the middle at the pivot mount. The weight of the trailer pushing down on the leaf springs/bushing spacers putting pressure/load on the leaf spring bushing bolt

@theweas4910 5 жыл бұрын

I Know You're Right But in order to know if it’s bad most of the time you will here it. Normally when at a very slow speed or from start to stopping while turning. Just listen for a creaking sound it’s hard to miss. Mine is bad right now and it drives me nuts listening to it.

@raymondchristensen338 5 жыл бұрын

michaelovitch june vippink. Floyd. Og. Div. Rock,. Pop

@raymondchristensen338 5 жыл бұрын

Pink. Floyd. Og. Div. Pop. Rock.

@hahahalolxd20000 7 жыл бұрын

clear and easy to understand, keep it up

@alexneil1967 8 жыл бұрын

your videos are so informative you not only show everything in perfect view but you explain everything. thank you so much for all your videos...

@bradpool127 3 жыл бұрын

I wondered how good those presses were. Thanks for the vid!

@daveihavenolastname8697 9 жыл бұрын

Always a great job Chris.Thanks

@jsmcguireIII 7 жыл бұрын

I'd position a wrench or some other solid object inside the bushing mount so it does not flex in and crack the welds. I also would use an impact gun and do a lot of penetrating oil first. thanks for the video I'm doing this job this weekend.

@shermanbird3891 4 жыл бұрын

My ball joint press specifically states not to use an impact tool on it. I never do.

@murraykriner9425 3 жыл бұрын

Just lost the lower ball joint on the 97' XR-7, and while I'm in the park, suspect that the bushing are gone as well. Great walkthrough in the replacement. Appreciate the help.

@rr3bro463 5 жыл бұрын

Thanks for the info & help. While borrowing the press kit they mentioned putting the new bushings in freezer until your ready. Seemed like it worked good.

@mikemcgloin702 8 жыл бұрын

you're a Godsend, thanks man

@Leoneidas 6 жыл бұрын

For stuff rusted like this, its best to hit it with the penetrating spray, everywhere, starting 24 hours in advance, and several times. Also, once force is applied to the press, rather than applying more and more pressure with a longer breaker bar, you can hit it with a hammer, while its under load, to break the hold. The impact of the hammer strikes will loosen the hold from years of press-fit and corrosion and soon it'll pop right out without having to put extreme force on it. You can always crank up the force if it's still stuck and hit it some more.

@JamesBrown-ux9ds 5 жыл бұрын

Has not change much this type of work since nineteen fifty seven - or since Dean Moriarty - but always a pleasure to see such an update up to date.

@stanshaw8506 6 жыл бұрын

Great job Chris on this video! Very well done, easy to understand! Thank You!

@BraxFilm 7 жыл бұрын

"pushing the bushing." my new favourite phrase :D

@georgemartinez8434 6 жыл бұрын

Great video and instructions, very impressive and very helpful indeed.

@chrisfix 6 жыл бұрын

Thanks! Glad the video was helpful!

@jimsimon738 3 ай бұрын

Your videos explain everything so well and so easy to understand, no one does it better than you. Thank you for sharing.

@diolyk3578 7 жыл бұрын

amazing... literally needed to do this today... this video just made my life a lot easier... thanks!

@redjstc9123 2 жыл бұрын

This guy is the father that we all wish to have in our childhood. U the best Chris

@BPoweredLove 6 жыл бұрын

Not only pro mechanic, but also pro KZfaq video editor which is VERY important. Nothing worse than a video being 3X or 4X as long as it needs to be because of lazy video posters. Thanks, Chris

@chrisfix 6 жыл бұрын

Thanks! I spend 120hrs on each video to make it as concise as possible!

@antonmoric1469 6 жыл бұрын

Well, while I always like to be positive on those kinds of videos, since the person is trying to help and often does have good information to share. But you are right, the diff is pro-level versus not. And this was a perfect video in the sense of great information delivered as concisely as possible, without being hurried or incomplete.

@classicreaction5340 5 жыл бұрын

Pro Tip: Take your control arms with the worn out bushings and place them in a fire pit with cardboard. Set the cardboard on fire until the old rubber bushings catch fire. They will start burning and literally pop out all by themselves. Allow the control arms to cool off naturally by themselves before touching them. You will usually have to remove the round metal casings but they will come out very easily. The old paint and grease will also burn off, making the control arms very easy to wire brush to bare metal.

@TurboRetard 3 жыл бұрын

A true pro tip

@lexuses3942 2 жыл бұрын

Awesome tip but any pro tips on getting them back in (without) a press? Would a c clamp work

@evanmorris1178 9 ай бұрын

Wouldn’t this anneal the steel control arms. Is this steel air hardening, I’m sure it’s got to be some sort of hardened , high strength steel.

@classicreaction5340 9 ай бұрын

@@evanmorris1178 control arms from the 60s 70s and 80s are just regular old stamped steel. The only control arms that I know are different are from the C4 Corvette in 1984, which switched to forged aluminum.

@evanmorris1178 9 ай бұрын

Thanks! Good to know.

@mauricioorantes9809 2 жыл бұрын

Very talented. Everything is logical and methodical.

@oliviabreezelamberttahuri4787 2 жыл бұрын

As a single mother trying to figure out how to afford to fix my car, this is so helpful! I've been trying to find a video I can understand so I can fix my car and get my sons and I back on the road sooner rather than later. Thank you so much.

@burstbomber3DkAcSk 2 жыл бұрын

Where you stay at Gurrrl? I got's you!... that's easy money!....

@MrFSTQ 9 жыл бұрын

Thank you so much, just don't stop doing this videos

@chrisfix 9 жыл бұрын

Atallah abdulaziz Thanks man! I wont! New videos every Thursday and a bonus video every Monday!

@danielsamaseia2128 8 жыл бұрын

ziinnnnggg!! right off.....good vid bro👍

@chrisfix 8 жыл бұрын

+Daniel Samaseia haha, thanks!

@lilbbbbbbb 6 жыл бұрын

Hit it with a couple uggaa duggaas haha

@c.a.g.3130 4 жыл бұрын

Very well explained. Great job, Chris!

@normpeplow3813 2 жыл бұрын

Nice job. Excellent videos, very clear and up close. Excellent explanations. I am too old to do this myself but sure do like to watch a master.

@dre04mach 7 жыл бұрын

Also, place your new bushings in the freezer until you install them... it'll shrink them just a little bit and make life easier :)

@johnsmith-sw7ii 8 жыл бұрын

Also a good idea to put a support piece between the sides of the control arm so it is not crushed or distorted by the press.

@larry2388 8 жыл бұрын

+john smith Absolutely! You almost always have to wedge something into the channel of the A arm to support and keep from crushing and deforming the A arm ends.

@TimHeagarty 8 жыл бұрын

+john smith Yeah, typically a short socket will fit in there and keep the ears from touching.

@mjb12141963 8 жыл бұрын

+Tim Heagarty where were you guys 2 years ago when I had to do this? I sure could have used that knowledge back then. LOL That thought never crossed my mind! I ended up returning the bushing and buying new control arms because I stretched out the openings for the bushings getting the old ones out.

@ernestogarcia162 7 жыл бұрын

remove lower control arm sedona

@larry2388 7 жыл бұрын

Honestly....this is one task that is worth having a shop do. I've done many A arms, and it's just too often a real nightmare doing these bushings.

@starsinmyeyes 4 жыл бұрын

This helped me. I didn't realize you could flip things over and still press out the bushing. Appreciate this video.

@beetle72 7 ай бұрын

Great video nice and clear, another thing to bear in mind is you should be adding some support for between the ears on the end of the control arms otherwise you can crush them together. This will make popping the bushing out harder and especially when pushing the new ones in. I use an old socket or a cut down bolt to wedge between the ears, this stops the two sides crushing inwards.

@chrisfix 7 ай бұрын

Thanks for the tip!

@zappa916 9 жыл бұрын

everytime i hear the fact that you guys can rent tools free from your auto parts store makes me want to migrate

@chrisfix 9 жыл бұрын

AngeV2 Haha, it is a nice perk!

@bradcloud7670 5 жыл бұрын

Where are you at that you cant?

@slickdawg4634 5 жыл бұрын

Who doesn’t do that?

@metalrott324 5 жыл бұрын

You have to leave the cost of the tool as a deposit which they return to you once you bring the tool back. It's free but not really.

@betosgarage 5 жыл бұрын

In Arizona , the cost of the tool is charged on your debit card & id is held until tool returned . So you pretty much buy it . Then return it lol

@BassManBobBassCovers 9 жыл бұрын

Ball joint press is the trick for the circular control arm bushings!!

@tongatours 8 ай бұрын

Very detailed and that's what I need cause I don't know shit bout cars until I started watching your videos. Cheers from the Kingdom of Tonga.

@daveshoe9776 2 жыл бұрын

If anyone has problems doing this job after watching this very complete video, then it's not Chris ' fault. i just priced new control arms for a two wheel drive 1994 Ram 1500 and they were $750.00. The mechanic wanted two thousand for a complete rebuild. This is life changing stuff and the difference between having to sell the truck or keep it on the road!!!

@KingOfPortraits 8 жыл бұрын

I need that camera you use lol

@wichitawwojak3786 9 ай бұрын

Of course, my favorite GT7 song.

@erickmarron2843 5 ай бұрын

Me too XD

@jeffherold8888 5 жыл бұрын

Great video. Good quality and clear instructions. Very helpful!

@gackal1982 5 жыл бұрын

excellent video, great camera work, focus and explanations you make it look so easy i feel motivated to do it now

@Scott_G 3 жыл бұрын

I feel like I'm watching a baby version of the ChrisFix I know now.

@chrisfix 9 жыл бұрын

***** Because I didnt want to use that penetrating fluid while working on my plastic tailgate cover. Might eat right though it! I really need a workbench badly!

@scottydntno 9 жыл бұрын

You should make a video to build one :-)

@chrisfix 9 жыл бұрын

***** I wish I had the room. My garage is tight. I was considering it though.

@scottydntno 9 жыл бұрын

I think you can for one in there. Hell, make one that folds up like one of those wall needs. Lol that would be cool as shit! !!!

@chrisfix 9 жыл бұрын

***** That would be really cool. I will have to start thinking about it!

@scottydntno 9 жыл бұрын

I saw a couple online....think I might have to make one myself. They look rather simple and space saving!!!

@MohammedAli-tb7zc 7 жыл бұрын

You've saved my ass on an engineering assignment i have because across the entire web, i couldn't find anything that would tell me what the bushings were made other than just 'rubber'. thanks for the help m8

@kyleg2029 4 жыл бұрын

Great tutorial, gifted instructor. 1st time watching your video, subscribed!

@muffinscars6187 7 жыл бұрын

BIZZZZZZZING!!!

@moparguy4524 5 жыл бұрын

5:15 zing right off 😂😂

@midnightrunner684 3 жыл бұрын

Yeeeee Haw

@NYCWendy1 2 жыл бұрын

This was awesome to watch. I’m not a mechanic, and I hv no tools. I just wanted to learn about bushings so I don’t get ripped off. Great video. Thank you!

@wdenegri 8 жыл бұрын

great camera work, I wont be doing this job( I lack a lot of tools) but thanks to you now I know what parts I have to buy.

@dunebasher1971 9 жыл бұрын

Nice tutorial, but shouldn't you really use a metal collar to fit between the "ears" of the control arm to ensure that the metal does not get crushed inwards while you're pressing? Control arms are often made of surprisingly thin pressed metal.

@chrisfix 9 жыл бұрын

dunebasher1971 Thanks man. I am unsure what you mean... They way I did it in this video is exactly how you are supposed to do it. You use a cup to press on the outside of the control arm ear and an attachment to press on only the bushing. Your control arm is designed to have bushings pressed in and out this way and will not bend. If I can bend a control arm with hand tools, it is a bad control arm and you need a new one anyhow. I hope that answers your question.

@dunebasher1971 9 жыл бұрын

ChrisFix Quite a few manufacturer's OEM control arms are thin enough to risk crushing them - solid-axle Jeep/Dodge ones for example. That's why the factory special tool for replacing the bushings comes with a metal collar to fit in between the ears to ensure they don't crush when the pressure is applied. Look up Miller tool 7932 for an example, the U-shaped piece is the collar. At 5:22 in your video, you can see one of the ears of the control arm bending inwards. The risk is that it doesn't spring back when the bushing pops free. When you're comparing the control arms at 7:20, you can see that the ears of the arm you've just pressed the bushings out of are noticeably deformed compared to the other arm. If it works for you, great, but it's worth knowing that there's a risk of deforming the ears so much that the new bushing will never seat properly. It wouldn't surprise me if the factory procedure for replacing those bushings specifies a special tool that includes a collar to sit between the ears to prevent them bending.

@chrisfix 9 жыл бұрын

dunebasher1971 Oh, I understand now. In this case, the bushing was bending the ear a little. In this case, it is a good control arm but as you said, some control arms are weak and it could damage the actual control arm. You could put a piece of metal or wood in between the two ears to prevent them from bending (like the collar you are talking about). Thanks for pointing that out man!

@codyapplegarth 4 жыл бұрын

@@dunebasher1971 At that point it also looks like a weld broke- I would consider that a safety risk and throw the items away.

@absurdengineering 4 жыл бұрын

@@codyapplegarth That poor wishbone got wrecked by doing the job improperly. It is definitely a failure waiting to happen. There was some proper crack initiation going on in at least two places. It will fail no problem. This video gets things about halfway right, but the things it gets wrong are cringe-inducing.

@rshelltrack 8 жыл бұрын

Did you damage the control arm at the 5:22 mark? It seemed to look like it pinched a little bit..? But overall very informative and great camera angled vids!

@niku10 8 жыл бұрын

+Rob ST he should have put a nut in between the arm to prevent it

@stradplayer90 8 жыл бұрын

He definetly did.

@michelauspimmelberger 7 жыл бұрын

yes the controlarm is cracked at 2 spots and should have been re-welded.

@NeilVanceNeilVance 7 жыл бұрын

Yes a spacer should be inserted to keep it all in jig before compression.

@antonmoric1469 6 жыл бұрын

Excellent DIY! Very clear and complete, thanks.

@jnrivers 3 жыл бұрын

I love this stuff. I think "hey I can do this!" Thanks ChrisFix.

@heartofdixie67 5 жыл бұрын

Funny thing is that a lot of times, you can actually buy the new complete control arms CHEAPER than buying the bushings separately and installing it yourself ! This was the case with my 98 Lincoln Mark VIII and 93 Town Car 🤣

@chrisfix 5 жыл бұрын

Yea that is totally true. For whatever reason, sometimes it’s cheaper to go that route. I would assume the person looking up the parts would notice that, hopefully.

@blackchip3 3 жыл бұрын

Am I the only one on this whole thread that noticed that when he pressed it out he broke the weld on the control arm lmao.

@Jagogjk1 3 жыл бұрын

Nope i saw that too 😅, and i saw your comment right before i was going to write my own, BTW do you also hear how depressing @chrisfix sounds on these old videos?