Just in the right time! Im just about to change the seals of my KTM which has WP forks. Thanks so much!

Sweet vid !! Excellent presentation, and VERY clear instructions !! Wonderful to hear from an expert. Thank you !!!

This is the reason always buy my parts from rocky mountain

Dustin - excellent job on this. I just did the forks on my 530EXC and followed you step by step. Thanks much.

Couple of comments. Lower end thread cap screw. It works better if you start the cap off with the forks still assembled. Only a couple threads. If it hangs up later on... put the fork spring in, push down on it so it bottoms in the tube, and the threaded portion will come off. Snap ring holding the fork oil seal in. One end is notched and will come off. Other end isn't notched and won't come off !

Thank you for this!! Just ordered all the parts I need to do it!

Great video thanks. My preload adjusters didn't unwind the cap just came off in one but it hasn't effected anything. I also got away without any special tools (insulation tape to drive the fork seals and protect the seals over the bushing recess and drilled an old spanner with 4mm holes and used the drill bits to unwind the top cap) I used 600ml of oil in each fork leg (2010 ktm exc) and forks feels brilliant now 👌

superb vid rebuilt my forks in half the time it would of taken after watching this.

Great vid! Need to service my forks over the winter and would like to DIY it. This vid explains it perfectly. Links to the tools like the fork driver, bullet etc would be great.

Thanks so much for the vid! Just wondering if it's necessary to remove the reboundand compression assembly or if it's possible to change seals without taking it out. Thanks!

Great job - lots of detail clearly presented and no time wasting! To what you're calling "dampening", I believe the technical term is damping.

Thank you great video helped me out alot

Question please - if just changing seals is it ok to leave damping assembly and compression adjuster in place?

Could you explain to me how to remove the cap from the bottom of the fork and put it back on? I have the fork just like this and I can not remove the bottom cap of vuleltas inside and it does not loosen.

HI! What is mandatory to replace ? only the oil seal and the dust seal?thank you for the vídeo great introctions.

do you have yo remove the fork damping rod to change the seal?

nice tutorials bro!👍

Very precise 👍

do you have to remove the damping rod to replace fork seals?

That’s what comes on n the 2016 350 sxf right cam I take the top cap off and put oil into n top do I have to take fork off and fill in bottom ? Thanks

Great Job...

Brilliant thank you

Hi me from Indonesia I really like your vidio😊

Hi! I own a 990 SM, is that the same kind of forks ?

Thanks 😊

I know this is old, but I have just rebuilt a set of 2004 forks and they have 3 bushings and a large spacer. I have heard to remove stiction, you have to remove a bushing and the spacer. But which bushing ? The middle one ?

Hi, thanks for the video!...which are the benefits of the fork seal grease? does not pollute the internal fork oil?? can we use normal grease or lithium grease?

When cycling my damping rod to remove air...on the right rebound side I get nice full stroke damping, while on left compression fork I only get damping fir the first few inches. I gather from other sites that this is normal...can you comment? 2018 250 EXC-F with no preload adjustment.

Is the process the same on the wp43 omthat came on the 2002 model ktm?

Hey Dustin dude! Whats the cheapest fix for wp aer forks? 22 ktm 350sxf

Do I need the thin 22mm wrench to do this?

Hi, I'm a Portuguese fan of your channel. Lots of practical technical information, and very well explained. I have a KTM exc 450 from 2005, and I did this oil and seal change operation, without disassembling the fork base, just removed the spring, emptied the oil, cleaned it and filled it with new oil and seals. At the end of one of the forks, the clicker always rotates without stopping. I am going to address this problem but in the meantime I would like some opinion of yours about what I have done wrong, and possible damage that I have to pay attention to. BTW, is there any video of changing the glass oil level check thing on these bikes? I have a smal leak there... Thank you in advance, for your attention. Come to Portugal for an adventure ride, i will show you guys the best trails.

The forks on my dirt bike are inverted. Can't I replace the seals with them on the bike?

nice vid

Hi... can you make a rebuild video of WP suspension 4860 ROTA SPLIT with EDS?

Hello I have an '08 sxf 250 European could you please tell me the capacity of the forks on mls (metric)!!!! Thanks

Adventure 1190 electronic fork rebuild would be a nice video :-)

Is it different with the showa forks or is it kinda same?

How much fork oil it takes in ml the fork pls

Why remove the compression fitting on the bottom?

is it safe to rotate the upper tubes on the forks 90 degrees when the forks are installed on the bike, for example to reorientate the facing of the protective stickers?

Anyone know of a video that shows how to disassemble the forks off a 2014 ktm 300xc? Thought this was it but I don’t have an adjustment on the bottom of my forks just a big Allen bolt

How to get the spring out and even more important, get it back in if it is rockhard?

good vid can u do one on how to replace fork seals on a fork similar to a 2008 yz 250f if u haven't already. ps most helpful videos out thanks for the services you provide.

Can you tell me the for seal size

What steps are necessary if I'm only changing the fork oil? Can I just remove the top spanner cap, dump and refill or do I need to back out all adjusters as per video? Thanks

Hello my cartridge is always spinning so i cant use a Torquewrench. With the impact wrench it is possible. Any tips?

Why do you want to coat the inside of dust seal with grease, wouldn't it smear grease over the inner tube and then catch dust afterward, and also please tell specifically which fork greade do you use

Can we use a fork oil level syringe on this style of fork? Would that be more accurate than measuring the oil volume? What would be a recommended oil level?

Question please - when you screw the top cap back on, is it until the first slight resistance or screw it until it stops home? cheers!

Can i buy the as usd

These forks remind me of the old 2004 yz250 forks.

Very nice and helpful video! :-) But I have one question: Do you have to remove the compression dampening fitting and pull the cartridge out, or can you leave it in as well? Does it matter when I am only replacing the fork seals?

Would my 2009 ktm xcw 200 have the same forks? And if so how much oil do I put in them? I can't find this information anywhere and I can't find a shop manuel anywhere that I can buy. Thanks!

Hi guys! What tipe of suspension grease do you use? I canot find anywhere the KTM recomended grease and i am lookibg for a replace. Can you tell me the type that you are using? Or maybe the properties that the grease should have?

I got my bottom bolt off but now putting it back on it just keeps spinning!!! what is supposed to hold it and stop the cartridge tube from spinning?

Hello my Spring Preload is locked what should be done to fix it?

A bicycle repair stand works great instead of a vise. Holds the fork tubes carefully.

Great video. Lots of great info. It’s damping rod. Not dampening rod. Damping means resistance to movement. Increase compression damping and your increasing resistance to compress. To dampen is to make something wet. Just sayin

Is it possible to do a poor man's oil change on these? Open the cap, unscrew and remove the spring, dump the oil, refill the same amount and install the spring back?

Sir can i buy the all tools???

just a heads up for everyone with these specific forks dont use an impact on the bottom compression assembly or atleast be very careful i used just a regular makita battery impact driver to zip mine on and i must have went overboard the first one went on fine, so i thought..... then the second one completely sheared off the aluminum collar on the assembly causing it to push right through into the fork totally ruined have to buy 2 new ones now, the first one didnt shear off but cracked around the entire edge and is barely hanging in there terrible design to make it out of aluminum they are not cheap either so when my new ones come i dont think im going to use an imact at all dont want to risk it

why does the buttom just spin

Air impact on the compression adjuster? Don't do this. If the cartridge is turning put the spring in and cap on temporarily and compress the fork a bit while tightening the adjuster.

This is why don’t have Kym it’s a joke how to do them

1,13 once? Are u sure?