Great video, I removed the lashers on my 2008 Charger SXT, It was a pain getting them off, I had to perform an special surgery: Make the top hole bigger (Used a drill bit then a carbide with my Dremel), You have to be careful with the debris, the arms are aluminum, through that hole used an old valve upsidedown as a punch (what a power punch!!!), Even though I had a hard time, they came off. I had to perform some machining in the holes for the new lashers because it was to tight to fit them in, specially the lock, but after 2 days straight working on that lasher replacement, worth the effort! This job is not for everybody, as an engineer I had to perform the drilling carefully like neurosurgery, especially for the aluminum debris not getting in the holes, I had to perform a special debris cleaning procedure
@lwjw31842 жыл бұрын
I need to know how you get them out of a 2004 dodge neon 2.0 rocker arm. There is no hole in the top only on the side for oiling.
@jessemiller59113 жыл бұрын
This is an excellent video. I’m going to make one tomorrow.
@billypat93702 жыл бұрын
Great video it’s on time for me thanks 🙏 I’m doin a valve job and the engine was tapping up top
@butters77814 жыл бұрын
How did you get the lash adjusters back in after removing?
@williamarchibald9826 Жыл бұрын
great video
@elifire41473 жыл бұрын
Mine is about 4x as yellow as that, where do I get a quality replacement assembly?
@juliantranquilino2769 Жыл бұрын
Good tutorial
@xushenxin Жыл бұрын
how to install one? hammer it in?
@Beemanshooter5 жыл бұрын
if you can get the old ones out. Didnt work for me ended up buying the complete assemblies
@jeromebowens68155 жыл бұрын
Where did you get the complete assembly
@Beemanshooter5 жыл бұрын
@@jeromebowens6815 At a Chrysler dealer, just Google it there's a lot out there.
@adventures895 жыл бұрын
How were you able to tell which lash adjusters were bad?
@demecoj5 жыл бұрын
They all have a spring inside of them. if you press the top of the lash adjuster and it goes down and comes back up its good. if it doesn't then its no good and need to be change. When a lash adjuster is stuck or has collapsed and there is no spring release it makes a tapping noise on the lifter cups.
@phigo4kins4 жыл бұрын
@@demecoj I thought when the Lifter is hard to push down means they're good? And when you're able to compress them means they're No good.. ??
@CheapskateGarage2 жыл бұрын
@@phigo4kins That depends on whether it's already filled with oil. If it's filled with air, it should squish down. Then when you release it, the internal spring should extend it again, drawing oil in through the check valve. Once filled with oil it should be "stiff" for some amount of time before bleeding down again. Even good ones do bleed down over time if there's pressure on them.
@wedgecharger9 ай бұрын
@@CheapskateGarage Bro ....How the H does that unpressurized piece of crap take up the clearance and give the Required valve lash clearence ? It is just a spring in there ?....and there is just a hole for some oil to maybe get in ?
@mariotorres30806 жыл бұрын
Saludos desde mexico
@phigo4kins4 жыл бұрын
Hey just wondering, Do/Did you have side to side play in Your rocker arms as well? 🤔
@Extremeineveryway4 жыл бұрын
Yes they do
@phigo4kins4 жыл бұрын
@@Extremeineveryway Ok, You still had The side to side play after replacing the Lifters and you installed it like that in your engine and it ran without issues/Knocking?
@phigo4kins4 жыл бұрын
@@Extremeineveryway Do you still have the car? How is it Holding up? Any Rocker Arm ticks/knocks? Or If you don't have the car anymore,, how long did your repair serve you? Hope I'm not asking too many questions, I'm only asking because, I'm about to do these lifters, but, I'm worried about the side to side play that it don't end up being another trouble for Me after toiling to replace these dreaded lifters.
@mustangadrian78996 жыл бұрын
Hi quick question I bought some rocker arm assembly when I received it the yellow thing like the orange thing on your video on the lifter is broken but I glued it would it still work ?
@Extremeineveryway6 жыл бұрын
mustang adrian check to see if the button has come off the lifter. If it's cracked so bad that the little tip can come off you're better off not to glue it. Try replacing it with one that's not cracked
@kevinpozos62285 жыл бұрын
Extremeineveryway what is that yellow thing called ? Could I just buy it separate
@demecoj5 жыл бұрын
I recommend that you change it and save your time and money going back inside that engine. installing a damage or broken part can cause damage.
@warwickdean6 жыл бұрын
Hi buddy, do you have a part number for these please?
@leonardanderson74206 жыл бұрын
For anyone who wants to replace the lash adjusters, the best place to look is partsology. They have them for $3 and some change. I got mine there. I rebuilt my rocker arm assembly. I got to do the other side( drivers) and I'm going to record it from beginning to end.
@elifire41473 жыл бұрын
@@leonardanderson7420 That's a non answer.
@sawzalljr3621 Жыл бұрын
The parts number is on partsology.
@warwickdean Жыл бұрын
@@sawzalljr3621 I fallen lucky in the end and managed to pickup a full delivery miles head complete for £350