Your videos have helped me throughout my 5 yrs in the industry! And YES! I completely missed the set screw! Daaaamn it

Thank you bro. You made a stressful situation easy. I followed your instructions and had success the first time. Well done.

Thanks for this tip. Really important

What's good J&N FAM! Excellent vid! I have this project to do tomorrow with replacement pump EZ4040G. The set screw was great info, that would have got me!!!!,Great explanation, way to keep it simple!!!! Much appreciated! stay safe!!

Frickin great video buddy!!!

Just bought my ar. Pump today. Will see how I am going to install. Thank you 🙏

The slot the key goes in is called the keyway FYI bro,good video

8:16 cheeky camera lady!! 😂

Great video man. Got to what to do, how to do it, and no fluff filler in between.

that was a good explanation ,thanks

Thanks man just rebuilt my first pump head👏🏼

Great job to you and your camera person - good video. I take it no set screw on the new pump? thanks for sharing

Well done.

Great video thank you ! ,, no washers on the bolts ?

Awesome - the spacer for the groove in the shaft is very important and your attention to detail solved my problem. Without the spacer there is no pressure. Great job...

You forgot the set screw

Thank you so much for the information

Great video .thanks

Nice video, thanks for sharing how to remove and install the pump.

well done thanks! DId you tighten the set screw after?

Perfect. Exactly what I was looking for thank you

I have the comet 550 being gear driven by a Kohler pro25 I can not find a set screw anywhere on it,do they have one or is it more likely just sized on shaft?

that's one good looking pump

Gracias desde México

Thank you, thank you.......my exact engine and pump. I wanted advice on the pump oil and oil level though. I'll call.

thanks , nice video

Nice work

This is what I was looking for. My pump was pretty tight and I couldn't get the set screw to come out. After much messing with trying to remove it, I tried putting two screwdrivers on either side in the slots, applied a bit of even pressure and voila!!!!! Wasn't I surprised to find the set screw was missing! Either it was never in there, or it loosened and came out while I was using the washer. The old key is corroded in the slot. I used some rust remover and steel wool to clean the shaft. Then applied a nice coating of anti-seize and installed the new pump. I'm all set and ready to start pressure washing again.

nice video, thank you. I have a pressure washer, the motor is great, washer is bad. Am I able to turn it into a water pump at all? if not what else would I be able to use the motor for? Thank you Sir.

Out of curiosity how come you didn't put the thez screw back in underneath the pump?

I just replaced a pump going from a worn out 4k 3.5 to a new commit 4k 4gpm and it seems like the pressure especially when using my service cleaner got worse. Was I suppose to prime the pump some how or something? Or should I turn the unloader all the way?

I bought a huahe petrol jet wash 208cc 5.5hp it's got 180bar what pump could I change it to to increase the bar rating, I bought it from lidl it'd a Parkside but the engine is huahe but the carburettor is Honda the pump is small compared to engine any suggestions on a decent strong pump that will fit, cheers

Quick question Isn’t there a gasket/o ring type piece inside the housing of the pump (near the shaft hole?) I think I might have lost/misplaced mine..

What kind of model pump is that exchange out for 4000 psi 13.5 HP Honda pressure washer ? I would love to upgrade mine to that brand.

Thanks

Good video 👏👏👏Sir I have a Simpson 3100 pressure washer machine is working fine no problems but I need more power what can I change to add more power to it ? Thanks for your time 🙏

Some one replaced mine has a gap between the pump and engine cus they put spacers is that ok

Was there anything wrong with the original pump? Would you recommend one with or without a bypass line?

What anti-seize do you recommend? Specific?

For anyone with corrosion, get a rubber mallet and mallet it to the side, eventually it’ll free up and you can slide it off 🙂

Bro please help me on this. I have this pump and it doesn't come with a quick connect for the chem injector. Instead, it has a proprietary thread for their own factory chem injector. Do you know what size or a part that will fit onto that pump so that I may buy any chem injector I want that has a quick connect? Thanks

Should you use locktite?

Can i remove power wash motor to use for go cart with out having to use water.

Should we put antisieze lube on the mounting bolts too or just the shaft ...I did not see you put any on the mounting bolts.... that's why I ask ...also do you replace the set screw before the mounting bolts ?....

So, I have to assume that the set screw isn't going to be used on this particular pump?

I replaced my pump with a general ez4040g pump on a Honda gx390. Pump seems to run great but now my gx390 is very hard to start? It’s always started very easy. Any advice? Thanks

My pressure washer does not have a key on the shaft. There's a screw that goes into the centre of the shaft - do you have any examples of installing this type?

It is called electrolysis and happens when you have two dissimilar metals together. Grease works fine as that's all anti seize is, just gray grease with graphite, copper or other metals mixed in. (copper mix may be copper colored of course)

Hi my pressure washer wont start(It did before) after replacing my pump. It's the same layout, brand, and looks exactly the same as my old pump except my old pump is 3600 psi and this pump is 3700 psi.... I am not sure if that matters

what pump replaces a Landa pump model# LG3030G.1?

You Forgot the set srew and on the other video you put one of the seals in the wrong ordervdoes that matter or not do they all have to be in the right order or is it ok to mix them up?

You should be using a Torque wrench on that because its an aluminum housing..

HI I HAVE SIMPSON PRESSURE WASHER 4000 PSI 3.5 GPM AND HOND ENGINE GX270 WHAT WATER PUMP IS THE BEST FOR THE MACHINE I HOPE YOU CAN HELP ME THANKS.

what if the set screw isn't in there and it still won't come off ? because we took out the main 4 bolts and there wasn't a set screw but it still won't come off

If you don’t mind me asking…what made you swap to a Cat pump…besides just demonstrating how to swap pumps? Why would someone want to swap a General for CAT

What do I do if the bolt inside of it came off like broke? I really need to know this as soon as possible

Nice Video, Thanks, I take it the New Cat Pump doesn't have a set screw?

quick question do you remove the red top on the water pump and replace it with the yellow top when ready to use

In this video I only have the question of the screw that I remove when I remove the pump? I didn't see that it will install it.

hi, if i change my 2,5gpm pump to 4gpm pump it will be ok?

So, say you have an axial cam pump, can you upgrade from one of those to a cat pump as well?

JN equipment. So how do you put that screw back in. After you slid pump on that shaft can you then turn it upside down again and pulll rope slowly to show "set screw" hole to put back in ? Or will that mess up the key placement inside? Any insight will be greatly appreciated. Im starting to see leaks of oil around the pump I use it seven days a week 3 hours a day fpr the past 3 years . and sometimes it seems to starve for pressure. I think its easier to just replace the pump then mess with the internals. thank you

now then can you help me iv going to make my own power washer with 15 hp lifan whot is the best pump to put on it for power hi mine

I don’t have a set screw and my pump is just stuck on. I’ve looked very carefully for about an hour and no screw. What could it be

Can you put a 5.5 GPM pump on a 4gpm 4000 psi machine. What one do you recommend and would the install be the same as this video. Tku

Qual é o modelo da primeira bomba que vc tira?

Hie how can l acess or where can l buy pressure pump plz assist

How can i get a preown pump for my machine

when putting screws back do you recommend loctite

Which pressure washer is this?

I replaced my pump and the key . I bought a new Allen head set screw and tightens it . I fill with non detergent 30 weight oil. Cranked unit, but it builds zero pressure!! What happened?

Set screw reinstall?

I removed the old water pump and installed the new one but the pressure wont como on.. what could it be

What do I do to remove a pump that is stuck on the shaft. Pumps motor and pump are working fine I need to replace the belt on my mi-t-m hot water hsp-3504

I have the same pressure washer. I cannot get this pump off of the shaft! All bolts and set screw removed but this thing will not budge. PB blast soaking and I have only got it to mo e maybe half an inch. Any advice would be helpful.

My pin stuck in the old pump any help plz

Bonjour comment démonter celle d un moteur honda gx340 11

Thanks bunches. The set screw was my issue... I think. Then it will be corrosion, probably.

Adding oil might be a helpful tip. What type? How much?

And you didn't use Locktite on the bolts. Why?

Do you not need a gasket where the pump connects to the motor?

👍

Where can you buy a key? I need one for my unit

You forgot your put the set screw in!!!

UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust kzfaq.infoUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.

where does the oil go into the pump

what about the old locking screw

How much tension should the belt have when you are done

What is the whole purpose of changing the pump? Is a brand new GP pump

What size is the keyway..??

GX parts chaya

You didn't put the set screw back in

You forgot the set screw!

Why would pressure wash cut out and use more fuel

Did you forget to install the "set screw"?

why did you replace the General Pump and replace it with a Cat pump?

You replaced without alankey

Did you forget to put back the set screw?

That is not an 8mm allen wrench. Looks like it might be a 1/8"

Has any of you ever heard of a Torque wrench? You aren't a mechanic without using one. Uneven Pressure is Baad...